JVC HR-J313EU Video Channel Set, Access Video Channel SET Mode, SET RF Output System

Page 44

44EN

SUBSIDIARYSETTINGS(cont.)

Video Channel Set

Video Channel (RF Output Channel) is the channel on which your TV receives picture and sound signals from the video recorder through the RF cable.

IMPORTANT

Perform the following steps only if —

—Video Channel Set has not been done correctly by the Auto Set Up function (☞ pg. 4).

—you set up the recorder's tuner by Preset Download (☞ pg. 6) instead of using the Auto Set Up function.

—interference appears in the TV picture after you have moved to a different area or a new station has started broadcasting in your area.

—you change the connection between your recorder and TV from RF connection to AV connection, or vice versa.

If you have connected the video recorder to your TV via both the RF cable and a 21-pin SCART cable (AV connec- tion), since you do not need the video channel you have to set the video channel to off.

If you have connected the video recorder to your TV via the RF cable only (RF connection), you have to set the correct video channel.

Before performing the following steps, make sure the recorder's power is off and there is no cassette inserted in the recorder.

1

2

3

ACCESS VIDEO CHANNEL SET MODE

Hold down STOP (5/8) on the recorder until the display panel shows the following.

SET RF OUTPUT SYSTEM

The blinking number on the display indicates the RF output system of your country. If you have selected MAGYARORSZAG (36), CESKA REPUBLIKA (42), POLSKA (48) or OTHER EASTERN EUROPE (EE) for the country setting (pg. 4, 8), press %Þ to set to "2". For other countries, set to "1". Then press OK or #.

(1: B/G 2: D/K)

SET VIDEO CHANNEL

With AV Connection

Press TV PROG – until the display panel shows "1OUT– –" (or "2OUT– –").

●Now the video channel is set to off.

With RF Connection

Press TV PROG + or – to set the video recorder to a vacant channel between 22 and 69 which is not occupied by any local station in your area.

(Ex.) If channel 50 is available in your area

Then set your TV to UHF channel 50.

●If the two vertical white bars appear clearly on the screen as shown to the right, go to step 4.

●If the two vertical white bars do not appear clearly, re-set the video recorder to another vacant channel and try again.

NOTES:

●If you set the video recorder to a channel which is occupied by a local station or has neighbouring channels that are occupied by local stations, the picture reception quality will be affected and some interference noise will appear on the TV screen. Be sure to select a vacant channel which has no broadcast on neighbouring channels.

●If you cannot obtain the two vertical white bars clearly with any channel between 22 and 69, consult your JVC dealer.

EXIT VIDEO CHANNEL SET MODE

4 Press OK on the remote control.

With AV Connection:

To view picture signals from the video recorder, set your TV to its AV mode.

With RF Connection:

The channel on which the screen in step 3 appears clearly is your video channel.

To view picture signals from the video recorder, set your TV to the Video Channel.

Page 43 Page 45
Image 44
Page 43 Page 45
Contents HR-J313EU Do not place the recorder Safety PrecautionsFor Italy Check Contents Basic ConnectionsSituate Recorder Connect Recorder to MainsAuto Set Up EN Initial SettingsIf you are referring to the front display panel If you are referring to the on-screen displayLanguage Code Via an RF cable only RF connectionYour TV to the Video Channel. Refer to ThisPreset Download ENUIf both auto channel set and auto clock set have failed Language for the on-screen displayJust Clock Just Clock onLanguage Access Main Menu Screen ENABLE/DISABLE ON-SCREEN DisplayOn-Screen Displays Return to Normal ScreenPower Save Mode TV Auto Power On Link FunctionsLI NK NexTView LinkColour System Set ModeAbout Ntsc Playback Counter and tape remaining time readings will be incorrectBasic Playback Load a CassettePoint Start PlaybackSearch Playback FeaturesPlayback Adjust Tracking Override Automatic TrackingManually Return to AutomaticAccess Mode SET Screen Select Picture Control SET ModeEN Playback Repeat PlaybackBasic Recording Recording Features Reset CounterSelect Channel to Watch Display Remaining TimeEngage ITR Mode Instant Timer Recording ITRSET Recording Duration Press Record on the recorderS.T. Picture System PreparationS.T., then press OK or #to set to on or OFFOr press Record on the recorder RecordingPlayback Timer Programming EN Timer RecordingTimer Warning Satellite Tuner UsersExpress Timer Programming Start TimeEnter Programme Stop TimeSET VPS/PDC Mode If no VPS/PDC signal is detected from the station, VPSVPS/PDC Recording Press TV Prog +Check, Cancel And Replace Programmes Press ä TimerPress Again to check More information. Each Time you press Next programmesAuto Timer Auto TIMER, then pressOK or #to select either On or OFFSelect AV2 Select Mode REC Link indicatorAutomatic Satellite Programme Recording Before performing the following stepsSET Edit Mode Edit From a CamcorderMake Connections SET RECORDER’S InputInput Mode Edit To Or From Another Video RecorderSET Recording DECK’S Start Source PlayerAV2 Select Setting AV2 IN/DECODER connectorRecorder Press %Þ to move the highlight bar pointer to AV2 SelectConnection To Satellite Tuner EN System ConnectionsSatellite Tuner Unit Back of TVDecoder Set AV2 Select to AV2. pgConnecting Using a Decoder Select Input ModeConnect Decoder SET TunerShowview Setup Subsidiary Settings ENNumber Enter Receiving Channel Position NumberAccess Auto CH SET EN SU Bsidiary SettingsTuner Set Auto Channel SetPerform Auto Channel SET View Confirmation ScreenSU Bsidiary Settings Storing Channels ManuallyWhen Receiving a Scrambled Broadcast Delete a ChannelChange Station Channel Position Press %Þ @ #until the item you want to move beginsAccess Manual Channel SET Screen Perform TuningAccess Manual Switch StationsTV Station And ID List SET Date and Time Clock SetTurn the Recorder on Default setting is OFF. Set as desired by pressing Recorder is preset to receive clock settingSET Just Clock Channel position to the number representingAccess Video Channel SET Mode Exit Video Channel SET ModeVideo Channel Set SET RF Output SystemTroubleshooting EN Timer Recording RoubleshootingÄ remain lit on the display panel. Is there Problem? Quest Ions and Answers ENIndex Front ViewRear View EN Index VCR, TV Prog +/-,TV +/-, TV MutingIN/OUT x 1, IN/DECODER x Speci FicationsRotary two-head herical scan Auto Set Up referring to the display panel Ex. Francais is selected for Belgium
Top Page Image Contents