JVC HR-J313EU specifications Basic Playback, Load a Cassette, Point, Start Playback, Stop Playback

Page 13

PLAYBACK

EN13

Basic

Playback

Turn on the TV and select the VIDEO channel (or AV mode).

	PLAY
	EW
	DISPLAY
STANDBY/ON
TIMER
REC LINK	TV PROG

STOP/EJECT

FF

The easiest, most basic operation possible with your video recorder is tape playback. Already-recorded signals on a video tape are read by your video recorder and displayed on your TV just like a TV programme.

		LOAD A CASSETTE
	Make sure the window side is up, the rear label side is
		facing you and the arrow on the front of the cassette is
1 pointed toward the recorder. Don’t apply too much
		pressure when inserting.
		● The recorder power comes on automatically and the
		counter is reset to 0:00:00.
		● If the record safety tab has been removed, playback
		begins automatically.

		FIND PROGRAMME START
2		POINT
	If the tape is advanced past the start point, press REW.
		To go forward, press FF.
		START PLAYBACK
	Press PLAY. “BEST” appears blinking in the recorder's

1 2 3

4 5 6

7 8 9

0

LAY
1	?

REW

3

STOP

2

4

FF

3 display panel during automatic tracking. (☞ pg. 20)

STOP PLAYBACK

Press STOP on the remote or STOP/EJECT on the

recorder’s front panel. Then press STOP/EJECT to

4 remove the cassette.

Usable cassettes

Tape Position Indicator

● Compact VHS camcorder recordings can be played on

this video recorder. Simply place the recorded cassette

into a VHS Cassette Adapter and it can be used just like

any full-sized VHS cassette.

The tape position indicator appears on screen when, from the Stop mode, you press FF, REW or perform an Index Search. The position of “5” in relation to “0”

(beginning) or “+” (end) 0 + shows you where you are

on the tape.

”O.S.D.” (☞ pg. 9) must

be set to “ON”, or the Beginning indicator will not appear.

3

+ +

1:23:45 REMAIN 2:35

End

● This video recorder can record on regular VHS and

Super VHS cassettes. However, it will record and play

back regular VHS signals only. It is not possible to play

back a recorded Super VHS tape.

NOTE:

Depending on the type of tape used, there may be times when the indication is not correct.

Image 13

Contents HR-J313EU For Italy Safety PrecautionsDo not place the recorder Basic Connections Check ContentsSituate Recorder Connect Recorder to MainsEN Initial Settings Auto Set UpIf you are referring to the front display panel If you are referring to the on-screen displayVia an RF cable only RF connection Language CodeYour TV to the Video Channel. Refer to ThisENU Preset DownloadLanguage for the on-screen display If both auto channel set and auto clock set have failedJust Clock Just Clock onLanguage ENABLE/DISABLE ON-SCREEN Display Access Main Menu ScreenOn-Screen Displays Return to Normal ScreenPower Save Mode Link Functions TV Auto Power OnLI NK NexTView LinkMode Colour System SetAbout Ntsc Playback Counter and tape remaining time readings will be incorrectLoad a Cassette Basic PlaybackPoint Start PlaybackPlayback Playback FeaturesSearch Override Automatic Tracking Adjust TrackingManually Return to AutomaticSelect Picture Control SET Mode Access Mode SET ScreenEN Playback Repeat PlaybackBasic Recording Reset Counter Recording FeaturesSelect Channel to Watch Display Remaining TimeInstant Timer Recording ITR Engage ITR ModeSET Recording Duration Press Record on the recorderPreparation S.T. Picture SystemS.T., then press OK or #to set to on or OFFPlayback RecordingOr press Record on the recorder EN Timer Recording Timer ProgrammingSatellite Tuner Users Timer WarningStart Time Express Timer ProgrammingEnter Programme Stop TimeIf no VPS/PDC signal is detected from the station, VPS SET VPS/PDC ModeVPS/PDC Recording Press TV Prog +Press ä Timer Check, Cancel And Replace ProgrammesPress Again to check More information. Each Time you press Next programmesAuto TIMER, then press Auto TimerOK or #to select either On or OFFREC Link indicator Select AV2 Select ModeAutomatic Satellite Programme Recording Before performing the following stepsEdit From a Camcorder SET Edit ModeMake Connections SET RECORDER’S InputEdit To Or From Another Video Recorder Input ModeSET Recording DECK’S Start Source PlayerAV2 IN/DECODER connector AV2 Select SettingRecorder Press %Þ to move the highlight bar pointer to AV2 SelectEN System Connections Connection To Satellite TunerSatellite Tuner Unit Back of TVSet AV2 Select to AV2. pg DecoderSelect Input Mode Connecting Using a DecoderConnect Decoder SET TunerSubsidiary Settings EN Showview SetupNumber Enter Receiving Channel Position NumberEN SU Bsidiary Settings Access Auto CH SETTuner Set Auto Channel SetView Confirmation Screen Perform Auto Channel SETStoring Channels Manually SU Bsidiary SettingsDelete a Channel When Receiving a Scrambled BroadcastChange Station Channel Position Press %Þ @ #until the item you want to move beginsPerform Tuning Access Manual Channel SET ScreenAccess Manual Switch StationsTV Station And ID List Turn the Recorder on Clock SetSET Date and Time Recorder is preset to receive clock setting Default setting is OFF. Set as desired by pressingSET Just Clock Channel position to the number representingExit Video Channel SET Mode Access Video Channel SET ModeVideo Channel Set SET RF Output SystemTroubleshooting EN Roubleshooting Timer RecordingQuest Ions and Answers EN Ä remain lit on the display panel. Is there Problem?Front View IndexRear View VCR, TV Prog +/-,TV +/-, TV Muting EN IndexRotary two-head herical scan Speci FicationsIN/OUT x 1, IN/DECODER x Ex. Francais is selected for Belgium Auto Set Up referring to the display panel