JVC HR-J313EU specifications Access Mode SET Screen, Select Picture Control SET Mode, EN Playback

Page 16

16ENPLAYBACK(cont.)

Repeat Playback

Your video recorder can automatically play back the whole tape 50 times repeatedly.

Picture Control

This feature helps you to adjust the playback picture quality according to your preference. *The default setting is "AUTO."

1

 

START PLAYBACK

Press PLAY.

2

 

ACTIVATE REPEAT PLAYBACK

Press PLAY and hold for over 5 seconds, then release.

 

● The Play indicator ( ) on the display panel blinks

 

 

 

 

slowly.

 

 

● The tape plays 50 times automatically, and then

 

 

stops.

 

 

 

3

 

STOP PLAYBACK

Press STOP at any time to stop playback.

NOTE:

Pressing PLAY, REW, FF or PAUSE also stops Repeat Playback.

 

ACCESS MAIN MENU

 

 

 

 

SCREEN

 

 

 

 

1 Press MENU.

 

 

 

 

 

ACCESS MODE SET

 

 

 

 

SCREEN

 

 

 

 

Move the highlighted bar (pointer) to "MODE SET" by

2 pressing %Þ, then press OK or #.

 

 

 

 

SELECT PICTURE

 

 

 

 

CONTROL SET MODE

 

 

 

 

Move the highlighted bar

MODE SET

 

 

 

 

(pointer) to "PICTURE

B. E. S. T.

ON

 

CONTROL" by pressing

 

PICTURE CONTROL

AUTO

 

3 %Þ, then press OK or #to

AUTO TIMER

OFF

 

 

select the desired mode.

O. S. D.

ON

 

DIRECT REC

ON

 

AUTO: Provides

POWER SAVE

OFF

 

optimised picture

AV2 SELECT

AV2

 

NEXT PAGE

 

 

 

 

benefits of B.E.S.T.

 

 

 

 

[5°] =

 

 

 

 

Picture System.

[MENU] : EXIT

 

 

 

 

Normally select

 

 

 

 

 

AUTO.

 

 

 

 

 

EDIT: Minimizes picture degradation during editing

 

(recording and playback).

 

 

 

 

SOFT: Reduces image coarseness when viewing

 

overplayed tapes containing a lot of noise.

 

SHARP: Clearer, sharper-edged picture when viewing

 

images with lots of flat, same-coloured surfaces

 

such as cartoons.

 

 

 

 

NOTES:

●When you select EDIT, SHARP or SOFT, the selected mode will not change until you select again.

●When you select EDIT to dub tapes, be sure to select AUTO after you finish dubbing the tapes.

RETURN TO NORMAL

SCREEN

4 Press MENU.

NOTES:

●When B.E.S.T. is OFF, "PICTURE CONTROL" switches automatically from AUTO to NORM.

●Select EDIT when you are dubbing tapes. Refer to page 30.

Page 15 Page 17
Image 16
Page 15 Page 17
Contents HR-J313EU For Italy Safety PrecautionsDo not place the recorder Check Contents Basic ConnectionsSituate Recorder Connect Recorder to MainsAuto Set Up EN Initial SettingsIf you are referring to the front display panel If you are referring to the on-screen displayLanguage Code Via an RF cable only RF connectionYour TV to the Video Channel. Refer to ThisPreset Download ENUIf both auto channel set and auto clock set have failed Language for the on-screen displayJust Clock Just Clock onLanguage Access Main Menu Screen ENABLE/DISABLE ON-SCREEN DisplayOn-Screen Displays Return to Normal ScreenPower Save Mode TV Auto Power On Link FunctionsLI NK NexTView LinkColour System Set ModeAbout Ntsc Playback Counter and tape remaining time readings will be incorrectBasic Playback Load a CassettePoint Start PlaybackPlayback Playback FeaturesSearch Adjust Tracking Override Automatic TrackingManually Return to AutomaticAccess Mode SET Screen Select Picture Control SET ModeEN Playback Repeat PlaybackBasic Recording Recording Features Reset CounterSelect Channel to Watch Display Remaining TimeEngage ITR Mode Instant Timer Recording ITRSET Recording Duration Press Record on the recorderS.T. Picture System PreparationS.T., then press OK or #to set to on or OFFPlayback RecordingOr press Record on the recorder Timer Programming EN Timer RecordingTimer Warning Satellite Tuner UsersExpress Timer Programming Start TimeEnter Programme Stop TimeSET VPS/PDC Mode If no VPS/PDC signal is detected from the station, VPSVPS/PDC Recording Press TV Prog +Check, Cancel And Replace Programmes Press ä TimerPress Again to check More information. Each Time you press Next programmesAuto Timer Auto TIMER, then pressOK or #to select either On or OFFSelect AV2 Select Mode REC Link indicatorAutomatic Satellite Programme Recording Before performing the following stepsSET Edit Mode Edit From a CamcorderMake Connections SET RECORDER’S InputInput Mode Edit To Or From Another Video RecorderSET Recording DECK’S Start Source PlayerAV2 Select Setting AV2 IN/DECODER connectorRecorder Press %Þ to move the highlight bar pointer to AV2 SelectConnection To Satellite Tuner EN System ConnectionsSatellite Tuner Unit Back of TVDecoder Set AV2 Select to AV2. pgConnecting Using a Decoder Select Input ModeConnect Decoder SET TunerShowview Setup Subsidiary Settings ENNumber Enter Receiving Channel Position NumberAccess Auto CH SET EN SU Bsidiary SettingsTuner Set Auto Channel SetPerform Auto Channel SET View Confirmation ScreenSU Bsidiary Settings Storing Channels ManuallyWhen Receiving a Scrambled Broadcast Delete a ChannelChange Station Channel Position Press %Þ @ #until the item you want to move beginsAccess Manual Channel SET Screen Perform TuningAccess Manual Switch StationsTV Station And ID List Turn the Recorder on Clock SetSET Date and Time Default setting is OFF. Set as desired by pressing Recorder is preset to receive clock settingSET Just Clock Channel position to the number representingAccess Video Channel SET Mode Exit Video Channel SET ModeVideo Channel Set SET RF Output SystemTroubleshooting EN Timer Recording RoubleshootingÄ remain lit on the display panel. Is there Problem? Quest Ions and Answers ENIndex Front ViewRear View EN Index VCR, TV Prog +/-,TV +/-, TV MutingRotary two-head herical scan Speci FicationsIN/OUT x 1, IN/DECODER x Auto Set Up referring to the display panel Ex. Francais is selected for Belgium
Top Page Image Contents