JVC HR-S6711EU Programme Recording, 34 EN, Select the L-2 Select mode, Recording mode

Page 34

34 EN

TIMER RECORDING (cont.)

Automatic Satellite

Programme

Recording

This function allows you to automatically record a satellite programme which is timer-programmed on your external satellite receiver. Connect a satellite receiver to the recorder’s AV2 (L-2) IN/DECODER connector and programme the timer on the satellite receiver. The recorder starts or stops recording by the signals input from the satellite receiver. After recording, the recorder’s power shuts off automatically.

ATTENTION

●Be sure not to turn on the satellite receiver before the programme is executed; otherwise, the recorder will start recording when the satellite receiver’s power is turned on.

●If you have connected another appliance other than a satellite receiver to the AV2 (L-2) IN/DECODER connector, be sure not to engage the Automatic Satellite Programme Recording mode; otherwise, the recorder will start recording when the connected appliance’s power is turned on.

●Automatic Satellite Programme Recording and timer- recording cannot be done at the same time.

Before performing the following steps:

●Make sure the satellite receiver is connected to the recorder’s AV2 (L-2) IN/DECODER connector. ( pg. 40, 41)

●Programme the timer on the satellite receiver.

●Insert a cassette with the safety tab in place.

A Select the L-2 SELECT mode.

Set “L-2 SELECT” to “A/V” or “SAT” ( pg. 37).

● When you select “SAT”, refer to “IMPORTANT” on page 40.

B Set the tape speed.

Press SP/LP (p).

C Engage the Automatic Satellite Programme

Recording mode.

Press and hold SAT# for about 2 seconds. The button lights up and the recorder turns off automatically.

NOTES:

●To disengage the Automatic Satellite Programme Recording mode, press SAT#. The button’s light goes off.

●If the recorder’s power is off, it is not possible to engage the Automatic Satellite Programme Recording mode.

●In step 3, if the SAT#button does not light but instead blinks quickly even though your satellite receiver’s power is off, Automatic

Satellite Programme Recording will not work properly with that satellite receiver*. If this is the case, perform “Express Timer Programming” ( pg. 30) to timer-record a satellite programme.

*Some satellite receivers output signals even if the power is off. Automatic Satellite Programme Recording is not possible with those satellite receivers.

●The SAT#button blinks while Automatic Satellite Programme Recording is in progress.

●For timer programming of the satellite receiver, refer to the instruction manual of the satellite receiver.

●Automatic Satellite Programme Recording is not possible if your satellite receiver does not have a timer.

●Pressing the recorder’s 1button while Automatic Satellite Programme Recording is in progress turns off the recorder’s power and disengages the Automatic Satellite Programme Recording mode.

●If there are more than one satellite programmes you wish to record with Automatic Satellite Programme Recording, it is not possible to set different tape speeds for each programme.

●Depending on the type of satellite receiver, the recorder may not record a slight portion of the beginning of the programme or may record slightly longer than the actual length of the programme.

●If you engage the Automatic Satellite Programme Recording mode when the satellite receiver’s power is on, the recorder will not start Automatic Satellite Programme Recording even though the SAT#button blinks. When the satellite receiver shuts off once and is turned back on again, the recorder starts recording.

●You can also record a programme from your cable system in the same way if the system has a timer.

●The B.E.S.T. system ( pg. 27) does not work while Automatic Satellite Programme Recording is in progress.

●Just Clock ( pg. 56) does not work when the Automatic Satellite Programme Recording mode is engaged.

●When the Automatic Satellite Programme Recording mode is engaged, or the recorder’s power is turned off after Automatic Satellite

Programme Recording is finished, the recorder will not enter the Timer mode even though “AUTO TIMER” is set to “ON” ( pg. 45).

●After Automatic Satellite Programme Recording, the number of recorded programmes will not be displayed on the front display panel for the Instant ReView function ( pg. 20).

Page 33 Page 35
Image 34
Page 33 Page 35
Contents Video Cassette Recorder Safety Precautions Moisture Condensation Front View Front Display Panel ON-SCREEN Display How To Use Operating JVC TVsConnect the recorder to TV Check the contentsSituate the recorder Connect the recorder to mainsTo connect to a TV with S-VIDEO/AUDIO in connectors Video ConnectionTurn on the recorder Auto Set Up10 EN Select your countryPress rt to select your language code Perform Auto Set UpSelect the language Press rt to select Auto and press OK or eSet the video channel Perform Preset Download12 EN Press rt to select CH - and press OK or eLanguage for the on-screen display Just ClockLanguage Access the Main Menu screenAccess the Country Set screen 14 ENAttach the Satellite Controller Installing Satellite ControllerSituate the Satellite Controller Make connectionsSetting satellite receivers brand and channel 16 ENNexTView Link TV Auto Power OnVCR Auto Standby Direct Rec Basic Playback 18 ENPause during playback Slow MotionVariable Speed Search Activate frame-by-frame playbackHigh-Speed Turbo Search 20 ENSkip Search Instant ReViewNext Function Memory Index SearchManual Tracking Soundtrack Selection 22 ENRepeat Playback Activate Repeat PlaybackSet the tape speed Recording Resume FunctionChoose a programme Start recording24 EN Instant Timer Recording ITREngage the ITR mode Watching AnotherTape Remaining Time Reset the counterEngage the S-VHS ET mode Set the counter displayReceiving Stereo and Bilingual Programmes Type of Broadcast On-screen Display Being ReceivedPlayback RecordingBefore performing the Showview Timer Programming Access the Showview screenAccess the Showview Program screen 28 ENSatellite Receiver Users Set the VPS/PDC modeEngage the recorder’s timer mode Guide Program Number SetExpress Timer Programming 30 EN Enter the channel position To Timer-Record Weekly Or Daily Serials VPS/PDC Recording Press PR+32 EN Select the programme to modify Cancel or change programme settingConfirm the overlapping programmes Overlapping programmes blink on the TV screenProgramme Recording Select the L-2 Select modeRecording mode 34 ENEdit From a CamcorderHighlight bar pointer to Access the Output/Input Set screenPress rt to move OUTPUT/INPUT SET, thenSelect and L-2 Input Setting Decoder connectorAnother Video Recorder 38 ENYour recorder Recorder Connecting To a Satellite Receiver Simple ConnectionsPerfect Connections Connect the decoder Select the input mode42 EN Set the tunerConnecting/Using a Stereo System Make connectionsSelect the mode Mode SetAccess the Mode Set screen Select the mode settingWhen this function is set to ON, the timer is You can set the B.E.S.T. Biconditional Equalised SignalThis feature helps you to adjust the playback picture Off, and automatically disengaged when the recorder is46 EN For ExampleAbout Ntsc Playback 48 EN Access the Auto Channel Set screenTuner Set Auto Channel SetView the Confirmation screen Perform Auto Channel SetPress OK twice 50 EN Manual Channel SetWhen Receiving a Scrambled Broadcast Delete a ChannelSet Stations a 52 ENSet Stations B TV Station And ID List Station NameVideo Channel Set Access the Video Channel Set modeExit the Video Channel Set mode 54 ENGuide Program Number Showview SetupGuide Program Number Set Enter the Guide Program numberClock Set Access the Clock Set screen56 EN Set the source channel position for clock data Set the date and timeSet Just Clock Start the clock operationTroubleshooting 58 ENRecording Other Problems 60 ENPlayback 62 EN Preset Download Auto Channel Set Auto Set UpConnecting To a Satellite Receiver Delete a Channel Timer warning display Tuner SetInternational telephone Language code Country code
Top Page Image Contents