JVC HR-S6711EU Perform Auto Channel Set, View the Confirmation screen, Press OK twice

Page 49

EN 49

IMPORTANT

●In certain reception conditions, station names may not be stored correctly, and Auto Guide Program Number Set may not work properly. If the Guide Program numbers are not set properly when you timer-record a TV programme using the SHOWVIEW system, the recorder will record a TV programme of a different station. When programming the

timer using the SHOWVIEW system, be sure to check the desired channel is selected correctly ( pg. 28, “SHOWVIEW® Timer Programming”).

●Your video recorder memorizes all detected stations even if

reception of some of them is poor. You can delete those stations with an unacceptable picture ( pg. 51, “Delete A Channel”).

NOTES:

●Fine tuning is performed automatically during Auto Channel Set. If you want to perform tuning manually, refer to page 52.

●If you perform Auto Channel Set when the aerial cable is not connected properly, “SCAN COMPLETED -NO SIGNAL-” appears on the TV screen in step 7. When this happens, make sure of the aerial connection and press OK; Auto Channel Set will take place again.

●If no sound accompanies the picture or the audio sounds unnatural on some channels that have been stored by Auto Set Up, the TV system setting for those channels may be incorrect.

Select the appropriate TV system for those channels ( pg. 51, “INFORMATION”).

F Perform Auto Channel Set.

Press OK twice.

● If you have connected the

 

 

recorder and your TV via AV

 

 

connection ( pg. 8), the

 

 

recorder automatically

 

 

performs the Preset

 

 

Download and the T-V LINK

 

 

screen will appear

 

 

( pg. 12).

 

 

● The Auto Set screen appears,

Beginning

End

and remains on screen while

the recorder searches for receivable stations.

As Auto Channel Set progresses, the “q” mark on the TV screen moves from left to right. Wait until the TV screen as shown in step 7 appears.

G View the Confirmation screen.

After “SCAN COMPLETED” is displayed on the TV screen for about 5 seconds, the Confirmation screen looking like the one to the right appears. The stations your recorder located appear on a Confirmation screen —

channel positions (PR),

channels (CH) and station names (ID –  pg. 53). The blueback screen and the programme currently being broadcast by the blinking station appear alternately for 8 seconds each. To view the next page, use the rt w e button on the remote control.

●The stations located in the selected country appear at the top of the list.

●The Guide Program numbers will also be set automatically during Auto Channel Set.

H Return to the normal screen.

Press MENU.

●Using the Confirmation screen, you can skip or add channel positions, enter station names and perform other operations. Refer to pages 50 – 52 for the procedures.

●Depending on reception conditions, the stations may not be stored in order, and the station names may not be stored correctly.

●For information on scrambled broadcasts, refer to page 51.

Page 48 Page 50
Image 49
Page 48 Page 50
Contents Video Cassette Recorder Safety Precautions Moisture Condensation Front View Front Display Panel ON-SCREEN Display Operating JVC TVs How To UseSituate the recorder Check the contentsConnect the recorder to TV Connect the recorder to mainsVideo Connection To connect to a TV with S-VIDEO/AUDIO in connectors10 EN Auto Set UpTurn on the recorder Select your countrySelect the language Perform Auto Set UpPress rt to select your language code Press rt to select Auto and press OK or e12 EN Perform Preset DownloadSet the video channel Press rt to select CH - and press OK or eJust Clock Language for the on-screen displayAccess the Country Set screen Access the Main Menu screenLanguage 14 ENSituate the Satellite Controller Installing Satellite ControllerAttach the Satellite Controller Make connections16 EN Setting satellite receivers brand and channelNexTView Link TV Auto Power OnVCR Auto Standby Direct Rec 18 EN Basic PlaybackVariable Speed Search Slow MotionPause during playback Activate frame-by-frame playbackSkip Search 20 ENHigh-Speed Turbo Search Instant ReViewNext Function Memory Index SearchManual Tracking Repeat Playback 22 ENSoundtrack Selection Activate Repeat PlaybackChoose a programme Recording Resume FunctionSet the tape speed Start recordingEngage the ITR mode Instant Timer Recording ITR24 EN Watching AnotherEngage the S-VHS ET mode Reset the counterTape Remaining Time Set the counter displayType of Broadcast On-screen Display Being Received Receiving Stereo and Bilingual ProgrammesRecording PlaybackAccess the Showview Program screen Access the Showview screenBefore performing the Showview Timer Programming 28 ENEngage the recorder’s timer mode Set the VPS/PDC modeSatellite Receiver Users Guide Program Number Set30 EN Express Timer ProgrammingVPS/PDC Recording To Timer-Record Weekly Or Daily SerialsEnter the channel position Press PR+32 EN Confirm the overlapping programmes Cancel or change programme settingSelect the programme to modify Overlapping programmes blink on the TV screenRecording mode Select the L-2 Select modeProgramme Recording 34 ENCamcorder Edit From aPress rt to move Access the Output/Input Set screenHighlight bar pointer to OUTPUT/INPUT SET, thenDecoder connector Select and L-2 Input Setting38 EN Another Video RecorderYour recorder Recorder Simple Connections Connecting To a Satellite ReceiverPerfect Connections 42 EN Select the input modeConnect the decoder Set the tunerMake connections Connecting/Using a Stereo SystemAccess the Mode Set screen Mode SetSelect the mode Select the mode settingThis feature helps you to adjust the playback picture You can set the B.E.S.T. Biconditional Equalised SignalWhen this function is set to ON, the timer is Off, and automatically disengaged when the recorder isFor Example 46 ENAbout Ntsc Playback Tuner Set Access the Auto Channel Set screen48 EN Auto Channel SetView the Confirmation screen Perform Auto Channel SetPress OK twice Manual Channel Set 50 ENDelete a Channel When Receiving a Scrambled BroadcastSet Stations a 52 ENSet Stations B Station Name TV Station And ID ListExit the Video Channel Set mode Access the Video Channel Set modeVideo Channel Set 54 ENGuide Program Number Set Showview SetupGuide Program Number Enter the Guide Program numberClock Set Access the Clock Set screen56 EN Set Just Clock Set the date and timeSet the source channel position for clock data Start the clock operation58 EN TroubleshootingRecording 60 EN Other ProblemsPlayback 62 EN Connecting To a Satellite Receiver Delete a Channel Auto Channel Set Auto Set UpPreset Download Timer warning display Tuner SetCountry code International telephone Language code
Top Page Image Contents