JVC HR-S6711EU specifications 60 EN, Other Problems

Page 60

60 EN			TROUBLESHOOTING (cont.)
OTHER PROBLEMS
	SYMPTOM	POSSIBLE CAUSE	CORRECTIVE ACTION
1.	Whistling or howling is heard from the	● The camcorder’s microphone is too	Position the camcorder so its microphone
	TV during camcorder recording.	close to the TV.	is away from the TV.
		● The TV’s volume is too high.	Turn the TV’s volume down.

2.	When scanning channels, some of	● Those channels have been designated to	If you need the skipped channels, restore
	them are skipped over.	be skipped.	them ( pg. 50).

3.	The channel cannot be changed.	● Recording is in progress.	Press 9 to pause the recording, change
			channels, then press 4 to resume
			recording.

4.	Channel settings that were made	● After the manual settings were made,	Perform manual setting again.
	manually seem to have changed or	Auto Channel Set was performed.
	disappeared.

5.	No channels are stored in the	● The TV aerial cable was not connected	Turn off the recorder once and connect
	recorder’s memory.	to the recorder when Auto Set Up was	the TV aerial cable to the recorder
		performed.	properly, then turn on the recorder again.
			The recorder will try Auto Set Up again
			( pg. 10).
		● The fully-wired 21-pin SCART cable was	Turn off the recorder once and connect
		not connected between TV and the	the fully-wired 21-pin SCART cable to the
		recorder when Preset Download was	recorder properly, then turn on the
		performed.	recorder again. Then perform Preset
			Download again ( pg. 12).

ATTENTION

This recorder contains microcomputers. External electronic noise or interference could cause malfunctioning. In such cases, switch the recorder off and unplug the mains power cord. Then plug it in again and turn the recorder on. Take out the cassette. After checking the cassette, operate the unit as usual.

Image 60

Contents Video Cassette Recorder Safety Precautions Moisture Condensation Front View Front Display Panel ON-SCREEN Display How To Use Operating JVC TVsCheck the contents Situate the recorderConnect the recorder to TV Connect the recorder to mainsTo connect to a TV with S-VIDEO/AUDIO in connectors Video ConnectionAuto Set Up 10 ENTurn on the recorder Select your countryPerform Auto Set Up Select the languagePress rt to select your language code Press rt to select Auto and press OK or ePerform Preset Download 12 ENSet the video channel Press rt to select CH - and press OK or eLanguage for the on-screen display Just ClockAccess the Main Menu screen Access the Country Set screenLanguage 14 ENInstalling Satellite Controller Situate the Satellite ControllerAttach the Satellite Controller Make connectionsSetting satellite receivers brand and channel 16 ENTV Auto Power On NexTView LinkVCR Auto Standby Direct Rec Basic Playback 18 ENSlow Motion Variable Speed SearchPause during playback Activate frame-by-frame playback20 EN Skip SearchHigh-Speed Turbo Search Instant ReViewIndex Search Next Function MemoryManual Tracking 22 EN Repeat PlaybackSoundtrack Selection Activate Repeat PlaybackRecording Resume Function Choose a programmeSet the tape speed Start recordingInstant Timer Recording ITR Engage the ITR mode24 EN Watching AnotherReset the counter Engage the S-VHS ET modeTape Remaining Time Set the counter displayReceiving Stereo and Bilingual Programmes Type of Broadcast On-screen Display Being ReceivedPlayback RecordingAccess the Showview screen Access the Showview Program screenBefore performing the Showview Timer Programming 28 ENSet the VPS/PDC mode Engage the recorder’s timer modeSatellite Receiver Users Guide Program Number SetExpress Timer Programming 30 ENTo Timer-Record Weekly Or Daily Serials VPS/PDC RecordingEnter the channel position Press PR+32 EN Cancel or change programme setting Confirm the overlapping programmesSelect the programme to modify Overlapping programmes blink on the TV screenSelect the L-2 Select mode Recording modeProgramme Recording 34 ENEdit From a CamcorderAccess the Output/Input Set screen Press rt to moveHighlight bar pointer to OUTPUT/INPUT SET, thenSelect and L-2 Input Setting Decoder connectorAnother Video Recorder 38 ENYour recorder Recorder Connecting To a Satellite Receiver Simple ConnectionsPerfect Connections Select the input mode 42 ENConnect the decoder Set the tunerConnecting/Using a Stereo System Make connectionsMode Set Access the Mode Set screenSelect the mode Select the mode settingYou can set the B.E.S.T. Biconditional Equalised Signal This feature helps you to adjust the playback pictureWhen this function is set to ON, the timer is Off, and automatically disengaged when the recorder is46 EN For ExampleAbout Ntsc Playback Access the Auto Channel Set screen Tuner Set48 EN Auto Channel SetPerform Auto Channel Set View the Confirmation screenPress OK twice 50 EN Manual Channel SetWhen Receiving a Scrambled Broadcast Delete a Channel52 EN Set Stations aSet Stations B TV Station And ID List Station NameAccess the Video Channel Set mode Exit the Video Channel Set modeVideo Channel Set 54 ENShowview Setup Guide Program Number SetGuide Program Number Enter the Guide Program numberAccess the Clock Set screen Clock Set56 EN Set the date and time Set Just ClockSet the source channel position for clock data Start the clock operationTroubleshooting 58 ENRecording Other Problems 60 ENPlayback 62 EN Auto Channel Set Auto Set Up Connecting To a Satellite Receiver Delete a ChannelPreset Download Timer warning display Tuner SetInternational telephone Language code Country code