JVC HR-S6711EU 54 EN, Access the Video Channel Set mode, Set the RF output system

Page 54

54 EN

SUBSIDIARY SETTINGS (cont.)

Video Channel Set

Video channel (RF output channel) is the channel on which your TV receives picture and sound signals from the recorder through the RF cable.

IMPORTANT

Perform the following steps only if —

—interference appears in the TV picture after you have moved to a different area or a new station has started broadcasting in your area.

—you change the connection between your recorder and TV from RF connection to AV or S-VIDEO connection, or vice versa.

If you have connected the recorder to your TV via the AV or S-VIDEO connection ( pg. 8, 9), since you do not need the video channel you have to set the video channel to off.

If you have connected the recorder to your TV via the RF connection ( pg. 8), you have to set the correct video channel.

Before performing the following steps:

Make sure the recorder’s power is off and there is no cassette inserted in the recorder.

A Access the Video Channel Set mode.

Hold down 0 on the recorder until the front display panel shows the following.

B Set the RF output system.

The blinking number on the display indicates the RF output system of your country.

●If you have selected MAGYARORSZÁG (36), CESKÁ REPUBLIKA (42), POLSKA (48), РОССИЯ (07) or OTHER EASTERN EUROPE (EE) for the country setting ( pg. 10, 14), press rt to set to “2”.

●For other countries, set to “1”. Then press OK. (1: B/G 2: D/K)

Then set your TV to UHF channel 50.

●If the two vertical white bars appear clearly on the TV screen as shown to the right, go to step 4.

●If the two vertical white bars do not appear clearly, re-set the video recorder to another vacant channel and try again.

NOTES:

●If you set the video recorder to a channel which is occupied by a local station or has neighbouring channels that are occupied by local stations, the picture reception quality will be affected and some interference noise will appear on the TV screen. Be sure to select a vacant channel which has no broadcast on neighbouring channels.

●If you cannot obtain the two vertical white bars clearly with any channel between 22 and 69, consult your JVC dealer.

D Exit the Video Channel Set mode.

Press OK on the remote control.

C Set the video channel.

With AV or S-VIDEO Connection

Press PR – until the front display panel shows “1OUT– –” (or “2OUT– –”).

●Now the video channel is set to off.

With AV or S-VIDEO Connection

To view picture signals from the video recorder, set your TV to its AV mode.

With RF Connection

The channel on which the TV screen in step 3 appears clearly is your video channel.

To view picture signals from the video recorder, set your TV to the video channel.

With RF Connection

Press PR + or – to set the video recorder to a vacant channel between 22 and 69 which is not occupied by any local station in your area.

(Example) If channel 50 is available in your area

Page 53 Page 55
Image 54
Page 53 Page 55
Contents Video Cassette Recorder Safety Precautions Moisture Condensation Front View Front Display Panel ON-SCREEN Display How To Use Operating JVC TVsConnect the recorder to TV Check the contentsSituate the recorder Connect the recorder to mainsTo connect to a TV with S-VIDEO/AUDIO in connectors Video ConnectionTurn on the recorder Auto Set Up10 EN Select your countryPress rt to select your language code Perform Auto Set UpSelect the language Press rt to select Auto and press OK or eSet the video channel Perform Preset Download12 EN Press rt to select CH - and press OK or eLanguage for the on-screen display Just ClockLanguage Access the Main Menu screenAccess the Country Set screen 14 ENAttach the Satellite Controller Installing Satellite ControllerSituate the Satellite Controller Make connectionsSetting satellite receivers brand and channel 16 ENTV Auto Power On NexTView LinkVCR Auto Standby Direct Rec Basic Playback 18 ENPause during playback Slow MotionVariable Speed Search Activate frame-by-frame playbackHigh-Speed Turbo Search 20 ENSkip Search Instant ReViewIndex Search Next Function MemoryManual Tracking Soundtrack Selection 22 ENRepeat Playback Activate Repeat PlaybackSet the tape speed Recording Resume FunctionChoose a programme Start recording24 EN Instant Timer Recording ITREngage the ITR mode Watching AnotherTape Remaining Time Reset the counterEngage the S-VHS ET mode Set the counter displayReceiving Stereo and Bilingual Programmes Type of Broadcast On-screen Display Being ReceivedPlayback RecordingBefore performing the Showview Timer Programming Access the Showview screenAccess the Showview Program screen 28 ENSatellite Receiver Users Set the VPS/PDC modeEngage the recorder’s timer mode Guide Program Number SetExpress Timer Programming 30 ENEnter the channel position To Timer-Record Weekly Or Daily SerialsVPS/PDC Recording Press PR+32 EN Select the programme to modify Cancel or change programme settingConfirm the overlapping programmes Overlapping programmes blink on the TV screenProgramme Recording Select the L-2 Select modeRecording mode 34 ENEdit From a CamcorderHighlight bar pointer to Access the Output/Input Set screenPress rt to move OUTPUT/INPUT SET, thenSelect and L-2 Input Setting Decoder connectorAnother Video Recorder 38 ENYour recorder Recorder Connecting To a Satellite Receiver Simple ConnectionsPerfect Connections Connect the decoder Select the input mode42 EN Set the tunerConnecting/Using a Stereo System Make connectionsSelect the mode Mode SetAccess the Mode Set screen Select the mode settingWhen this function is set to ON, the timer is You can set the B.E.S.T. Biconditional Equalised SignalThis feature helps you to adjust the playback picture Off, and automatically disengaged when the recorder is46 EN For ExampleAbout Ntsc Playback 48 EN Access the Auto Channel Set screenTuner Set Auto Channel SetPerform Auto Channel Set View the Confirmation screenPress OK twice 50 EN Manual Channel Set When Receiving a Scrambled Broadcast Delete a Channel52 EN Set Stations aSet Stations B TV Station And ID List Station NameVideo Channel Set Access the Video Channel Set modeExit the Video Channel Set mode 54 ENGuide Program Number Showview SetupGuide Program Number Set Enter the Guide Program numberAccess the Clock Set screen Clock Set56 EN Set the source channel position for clock data Set the date and timeSet Just Clock Start the clock operationTroubleshooting 58 ENRecording Other Problems 60 ENPlayback 62 EN Preset Download Auto Channel Set Auto Set UpConnecting To a Satellite Receiver Delete a Channel Timer warning display Tuner SetInternational telephone Language code Country code
Top Page Image Contents