Peerless Industries SA771PU manual Tools Needed for Assembly, Table of Contents

Page 2

Note: Read entire instruction sheet before you start installation and assembly.

WARNING

•Do not begin to install your Peerless product until you have read and understood the instructions and warnings contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, for US customers please call Peerless customer care at 1-800-865-2112, for all international customers, please contact your local distributor.

•This product should only be installed by someone of good mechanical aptitude, has experience with basic building construction, and fully understands these instructions.

•Make sure that the supporting surface will safely support the combined load of the equipment and all attached hardware and components.

•Never exceed the Maximum UL Load Capacity. See page one.

•If mounting to wood wall studs, make sure that mounting screws are anchored into the center of the studs. Use of an "edge to edge" stud ﬁnder is highly recommended.

•Always use an assistant or mechanical lifting equipment to safely lift and position equipment.

•Tighten screws ﬁrmly, but do not overtighten. Overtightening can damage the items, greatly reducing their holding power.

•This product is intended for indoor use only. Use of this product outdoors could lead to product failure and personal injury.

•This product was designed to be installed on the following wall construction only;

WALL CONSTRUCTION		HARDWARE REQUIRED
•	Wood Stud	Included
•	Wood Beam	Included
•	Solid Concrete	Included
•	Cinder Block	Included
•	Metal Stud	Contact Qualiﬁed Professional (not evaluated by UL)
•	Brick	Contact Qualiﬁed Professional (not evaluated by UL)
•	Other or unsure?	Contact Qualiﬁed Professional

Tools Needed for Assembly

• stud ﬁnder ("edge to edge" stud ﬁnder is recommended)

• phillips screwdriver

• drill

• 3/16" (5 mm) drill bit for wood studs, 3/8" (10 mm) drill bit for concrete

• level

Table of Contents

Parts List	3, 4
Wall installation	6, 7
Installing Adapter Brackets to Display	8-13
Mounting Flat Panel Display	14
Cable Management	16

2 of 70

ISSUED: 10-30-09 SHEET #: 095-9299-11 03-22-12

Image 2

Contents Models SA771PU Max UL Load Capacity 200 lb 90.7 kgTools Needed for Assembly Table of ContentsParts List SA771PUAdapter Bracket Fasteners Wall Plate Optional Horizontal Adjustment of Wall Arm on Wall PlateDetail Wall Plate Rail Slide PlateWood Stud Installation to Double-Stud WallWood Stud CS = Center of Display Installation to Solid Concrete or Cinder Block Solid Concrete Cinder BlockFor 65 Panasonic Display Installing Extension Brackets to Universal Adapter BracketsTapping Screws Holes For 65 Sharp DisplayFixed STOP-POSTION #3 Installing Adapter Brackets to DisplayFixed STOP-POSTION #4 Fixed STOP-POSTION #2Center Display Brackets Vertically on Back of Display Display MULTI-WASHER Display Spacer MULTI-WASHER ScrewBrackets Self Tapping Screws Vesa 200 x 200 or Vesa 200 x 100 Mounting PatternOuter Mounting Holesinner Self Tapping Screws BracketsFixed Stop Position #1 with Display Screw Multi Washer BracketDisplaydisplay Screwbracket MULTI-WASHER Adapter Plate Dedicated PLP Plate Adapter PlateTension Knob Adjustment of Flat Panel DisplayRear View ScrewsWall Plate Rails Cable ManagementCable Arm Tension Adjustment Tension Screw Tension ScrewsModelos SA771PU Máxima Capacidad de Carga para UL 200 lb 90.7 kgEspañol Herramientas necesarias para el ensamblajeTabla de Contenido 19 deLista de piezas Español 20 deFijaciones para los soportes adaptadores 21 deRiel DE LA Placa DE Pared Placa Deslizable DetallePlaca DE Pared Brazo DE ParedCP = Centro DE LA Pantalla Instalación en una pared con montante de madera únicoMontante 23 deConcreto Macizo Bloque DE Hormigón DE Escorias 24 de25 de Pantalla Panasonic dePantalla Sharp de 26 de Instalación de los soportes adaptadoresPosición Fija DE Descanso N.O Pantalla Soportes DE 27 de28 de Pantalla Arandela Múltiple TornilloPantalla Espaciador Arandela Múltiple Tornillo 29 de Vesa 200 x 200 o Vesa 200 x 100 Patrón de montajeDE LA Pantalla Arandela Múltiple Soportes DE LA Pantalla Tornillo 30 deEvaluados por UL Consulte la hoja de Instalación de la pantalla planaﬁg .3 E 31 dePerilla DE Tensión Ajuste de la pantalla planaVista Trasera 32 deRiel DE LA Placa DE Pared Manejo de cablesRanura Cable Los rieles de la placa de pared, como se muestra 33 deTornillos Tensores Ajuste Tensor del BrazoNota No lo gire más de media vuelta 34 deModèles SA771PU Capacité de Charge Maximale por UL 200 lb 90.7 kgFrançais Outils nécessaires au montageTable des Matières 36 surListe des pièces Français 37 surFixations du support adaptateur 38 surMontant DE Plaque Murale Plaque Coulissante DétailPlaque Murale Bras MuralMontant Installation sur un mur à montant en boisMontant CE = LE Centre DE L’ÉCRAN 40 surConcreto Macizo Bloque DE HOR- Migón DE Escorias 41 sur42 sur Écrans Panasonic deÉcrans Sharp de 43 sur Installation des Supports Adaptateurs à lécranPosition Darrêt Fixe no 4 Position Darrêt Fixe no Écran Supports DE L’ÉCRAN 44 surUniverselle ÉcranRondelle Écranrondelle Entretoise UniverselleVesa 200 x 200 ou Vesa 200 x 100 Modèle de montage 46 surÉcran VIZ Rondelle Universelle Supports Décran Vesa 200 x 200 ou Vesa 200 x 100 Modèle de montage suiteRondelle VIZ Universelle Supports Décran Écran 47 sur48 sur Installation de l’écran platPlaque PLP Dédiée non évalué UL Veuillez Bouton DE Tension Réglage d’un écran platVUE Arrière VIS M8 X 40 MM DétailMontant DE Plaque Murale Gestion des câblesFente Câble 50 sur51 sur Réglage de la tension du brasVIZ DE Tension Modelle SA771PU Maximale UL Tragfähigkeit 200 lb 90.7 kgDeutsch Für den Zusammenbau erforderliche WerkzeugeInhaltsverzeichnis Teileliste Beschreibung Anz Teil NrBefestigungsteile Für Adapterhalterung Wandplattenschiene Gleitplatte DetailansichtWandplatte WandarmAnbringung an Wänden mit einer Holzständerreihe CS = in DER Mitte DES BildschirmsPorenbetonstein Anbringung an Massivbeton oder PorenbetonsteinMassivbeton 58 vonFür 65 Zoll Panasonic-Display Für 65 Zoll Sharp-DisplayFeste Anschlagposition NR Installation Adapterhalterungen zur BildschirmansichtSchrauben 60 vonBildschirm Halterungen Bildschirme mit ﬂacher Rückseite Vesa 200 x 200 oder 200 x 100 Vesa Montage-Muster Richten Sie eine Bildschirmhalterung mit einer Schrauben Adapterplatte Anbringung des FlachbildschirmsFür spezielle PLP-Platte nicht UL-zugelassene Spezielle PLP-PLATTE AdapterplatteRückansicht Einstellung des FlachbildschirmsDraufsicht SpannknopfWandplattenschiene KabelführungSchlitz Kable Aeinstellung der Armspannung SPANNUNGS-SCHRAUBELimited FIVE-YEAR Warranty Garantie DE Cinq ANS