Heath Zenith 598-1116-10 Indoor and outdoor Wireless Motion Sensor, Select Night or 24 Hour Mode

Page 6

indoor and outdoor

Wireless Motion Sensor

Installing Indoor Motion Sensor Using Optional

Mounting Bracket

Indoor Wireless Motion Sensor

Outdoor Wireless

Motion Sensor

Features:

•No wiring required.

•Up to 30 feet sensing range, 150° Coverage (Indoor).

•Up to 70 feet sensing range, 180° Coverage (Outdoor).

•Adjustable sensitivity.

•Day/Night or Night only operation.

•Test mode.

•Uses 2 AA batteries.

•Can be mounted directly to wall or with mounting bracket (included) (Indoor).

•Wall or eave mount (Outdoor).

•Controls receivers up to 100 feet away.

Note: Mount the indoor motion sensor so that it can be angled up or down to give you the desired coverage above the floor level.

1.Attach ball mounting bracket to rear of motion sensor. The ball mounting bracket is designed to mount to the rear of the sensor in three possible directions depending upon the installation requirements. To attach the ball mounting bracket, follow the steps shown below:

•Determine the best mounting position of the sensor for the coverage desired.

•Determine the best location of the wall mounting bracket.

•Insert the tabs on the ball mounting bracket into the tab slots on the rear of the sensor that best align the sensor with the wall mounting bracket.

•Remove the batteries.

•Using a philips-head screwdriver, insert mounting screw into the hole in the battery compartment that aligns with the hole on the rear of the ball mounting bracket. Tighten securely.

Select Night or 24 Hour Mode

These sensors are able to detect motion day and night or night only. To set the detection mode, remove battery compartment

Ball Mounting

Rear of Sensor

cover by sliding the cover down. Remove batteries if necessary. Slide the DETECT switch to either the DAY/NIGHT or NIGHT ONLY position. Replace battery compartment cover by reversing the above instructions.

Installing Batteries

•Before mounting outdoor motion sensor, remove battery compart- ment cover by sliding the cover down.

•For indoor motion sensor, install batteries after sensor is in- stalled.

Install 2 AA batteries according to polarity markings inside the battery compartment. Replace battery compartment cover by reversing the above instructions.

Bracket Screw

Tab Slots

Tab

Swivel

Ball Mounting Ball

BracketMount

Detect

Control

DAY NIGHT

NIGHT ONLY

 

 

 

 

 

 

1 2 3 4

 

DETECT

CODES

 

 

CODE

DETECT

ON-TIME RANGE

 

 

 

(MINUTES)

 

 

DAY

NIGHT

5 1 TEST

 

1 2 3 4 NIGHT

ONLY

MIN

MAX

Attaching Ball Mounting Bracket to Indoor Motion Sensor

(Vertical Installation Shown)

2.

Place sensor mounting bracket against surface to be mounted

 

on and mark hole locations with pencil or center punch.

3.

Using a 2.5 mm (0.1”) drill bit, drill two pilot holes for mounting

 

screws. If not mounting directly to wood or wood stud, drill 5 mm

 

(0.2”) pilot holes and use the included wall anchors.

4.

Attach indoor motion sensor mounting bracket to a sturdy object

 

(i.e. wall,ceiling,post, etc.) usingtwo screwsprovided.Make sure

 

unit has an unobstructed view. Note: Attach mounting bracket

Outdoor Motion Sensor

Indoor Motion Sensor

(Rear View)

(Front View)

Battery Compartment

vertically if connecting to a curved surface such as a post.

5. Install motion sensor to mounting bracket. Using a Philips-head

screwdriver, loosen the clamp screw on the mounting bracket.

Insert swivel ball mount on sensor into mounting bracket socket

598-1116-10

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Example 2 Code Settings, System FeaturesCode Settings Example 1 Code Settings, SystemLamp Socket Converter Floodlight Code Switch LocationsRemote Control Add-A-Switch Entry Switch Indoor Plug-In ConverterOptional Car Visor Clip Included Remote ControlRear View of Remote Control Function ControlsBattery Replacement Add-A-SwitchInstallation Add-A-Switch Removing Battery TabBattery Replacement Entry SwitchMounting Configurations and Possible Directions Movement Important ConsiderationsInstalling Batteries Indoor and outdoor Wireless Motion SensorSelect Night or 24 Hour Mode Battery CompartmentInstalling Indoor Motion Sensor Directly To Wall Installing Outdoor Motion SensorCheck Operation and Adjustment Indoor and Outdoor Motion Sensor Sensitivity Adjusting Outdoor Motion Sensor CoverageOutdoor Motion Sensor Coverage Area Motion Sensor ControlsLamp socket converter Receiver InformationIndoor Plug-In Converter SpeakerWiring Floodlight Install fixture in accordance with local codesJunction box ground wire to green Ground screw on fixture FloodlightNo Service Parts Available for this Product Troubleshooting GuideTechnical Service Regulatory InformationTWO Year Limited Warranty Ejemplo 1 Calibraciones del código, sistema CaracteristicasCalibraciones DEL Código Ejemplo 2 Calibraciones del código, sistemaTapa Ubicaciones DE LOS Interruptores DE Circuito ImpresoTornillo Convertidor enchufable para usarse Bajo techoControles de las funciones Control remotoPresilla opcional del visor del carro incluida Vista posterior del control remotoOperación Interruptor a añadibleInstalación Reemplazo de la bateríaInterruptor DE Entrada Consideraciones importantesControl Seleccione modo nocturno o modo de 24 horasInstalación de las baterías Compartimento de la bateríaMovimiento De montajeTornillo de la Abrazadera Montura giratoria de bola Tornillo de MontajeInstalación del detector de movimiento Instalación del detector de movimiento para uso ExteriorRevisión de la operación y de la regulación Detector de movimiento para uso exterior Los controlesControles del detector de movimiento Apunte el detectorConvertidor del zócalo de la Lámpara Información DEL ReceptorConvertidor enchufable para Usarse bajo techo Ubicación de los controlesEmpaque ReflectorNegro Cableado del reflectorInformación Regulatoria Guía de Análisis de AveríasServicio Técnico No hay piezas de servicio disponibles para este productoGarantía Limitada a 2 Años Exemple 1 Réglage des codes, System CaractéristiquesRéglage DES Codes Exemple 2 Réglage des codes, systèmeEmplacement DES MICRO-INTERRUPTEURS Télécommande Interrupteur d’appoint Interrupteur d’entréeVue arrière de la télécommande TélécommandeCommandes des fonctions Pince de pare-soleil d’automobile facultative CompriseFonctionnement Remplacement de la pileInterrupteur d’appoint Retrait de l’onglet de la pileRetrait de l’onglet de pile Interrupteur D’ENTRÉETournevis plat Détails importantsDétecteurs DE Mouvement Sans FIL Intérieurs ET Extérieurs Sélection du mode de nuit ou du mode 24 heuresInstallation des piles Compartiment des pilesImportant Serrer à la main seulement, ne pas trop serrer Détecteur deCommandes du détecteur de mouvement Installation du détecteur de mouvements extérieurInstallation du détecteur de mouvement Vérification du fonctionnement et du réglageZone de couverture du détecteur de mouvements intérieur Zone de couverture du détecteur de mouvements extérieurMouvementMouvement Convertisseur de douille ’ampoule Informations SUR LE RécepteurConvertisseur enfichable intérieur Haut-parleurProjecteur Noir à noirCâblage du projecteur Renseignements de règlements Service TechniqueGuide DE Dépannage Aucune pièce de rechange n’est disponible pour ce produitGarantie Limitée DE 2 ANS Çais fran 598-1116-10

598-1116-10 specifications

The Heath Zenith 598-1116-10 is an advanced motion-sensing outdoor light designed to enhance security and functionality around homes and businesses. This fixture is engineered with the latest technologies to provide reliable performance while ensuring energy efficiency and ease of use.

One of the main features of the 598-1116-10 is its state-of-the-art motion sensor. The device employs a passive infrared (PIR) technology that detects movement within a significant range, ensuring that any motion in its monitored area triggers the light. The sensor is adjustable, allowing users to customize the detection range and sensitivity to suit their specific environment. This adaptability is crucial for minimizing false alarms from unwarranted movements, such as passing cars or animals.

In addition to its motion-detection capabilities, the Heath Zenith 598-1116-10 offers various lighting options. The fixture is equipped with a powerful LED light source that produces a bright output while consuming less energy than traditional incandescent bulbs. This not only aids in lowering electricity costs but also contributes to a longer lifespan for the light, reducing the frequency and hassle of bulb replacements.

The design of the 598-1116-10 reflects both aesthetic appeal and functional robustness. The weather-resistant construction ensures that the light can withstand various climatic conditions, making it suitable for installation in different outdoor environments. The sleek and modern design complements a wide range of architectural styles, enhancing the property’s overall curb appeal.

Another important characteristic of this outdoor security light is its convenient operating features. The device includes a manual override option, allowing homeowners to keep the light on continuously for extended periods when needed, such as during gatherings or outdoor events. Additionally, the light can be set to operate on a timer, providing flexibility and control over illumination schedules.

In conclusion, the Heath Zenith 598-1116-10 stands out in the outdoor lighting market due to its motion-sensing technology, energy-efficient LED lighting, durable design, and user-friendly features. It serves not only as a means of illumination but also as a crucial security element, helping to deter potential intruders while offering peace of mind for property owners. This combination of practicality and style makes the 598-1116-10 a top choice for those looking to enhance their outdoor lighting system.
Top Page Image Contents