Heath Zenith 598-1116-10 operating instructions Installing Indoor Motion Sensor Directly To Wall

Page 7

(Note: You should hear a snap). Aim sensor toward area where detection is desired. Tighten clamp screw.

Mounting

 

Mounting Screw

Nut

 

Bracket Socket

 

Mounting

 

 

Bracket

 

 

Clamp

 

 

Screw

 

 

Swivel Ball Mount

 

Battery Compartment

Sensor

Cover

 

 

Attaching Indoor Motion Sensor to Mounting Bracket

Installing Indoor Motion Sensor Directly To Wall

Note: Mount the indoor motion sensor so that it is approximately

between waist and shoulder level above the floor (Example: Level with light switch, under counter top, etc.).

1.Determine the best mounting position of the sensor for the coverage desired. Remove the batteries.

2.Place indoor motion sensor against surface to be mounted on. Using two of the holes on the rear of the battery compartment, mark hole locations with pencil or center punch.

3.Using a 2.5 mm (0.1”) drill bit, drill two pilot holes for mounting screws. If not mounting directly to wood or wood stud, drill 5 mm (0.2”) pilot holes and use the included wall anchors.

4.Attach indoor motion sensor to a sturdy object (i.e. wall, cabinet, post, etc.) using two screws provided. Make sure unit has an unobstructed view.

IMPORTANT: Hand tighten only - do not overtighten.

Motion

Counter

Top

Sensor

 

Mounting

Screw

Attaching Indoor Motion Sensor Directly to Wall

Installing Outdoor Motion Sensor

1. Installsensormountingbracketwheremotiondetectionisdesired.

 

Attach sensor mounting bracket to a sturdy object (i.e. tree, post,

 

house, etc.) using two screws provided. Make sure unit has an

 

unobstructed view. Note: Attach mounting bracket vertically if

 

connecting to a curved surface such as a post.

ENGLISH

2. Install motion sensor to mounting bracket. Using a Philips-head

screwdriver, loosen the clamp screw on the mounting bracket.

 

Insert swivel ball mount on sensor into mounting bracket socket

 

(Note: You should hear a snap). Aim sensor toward area where

 

detection is desired. Tighten clamp screw.

 

IMPORTANT: The sensor must be mounted with the bottom cover

 

facing down in order to maintain water tightness.

 

 

Mounting Bracket

 

Mounting

 

 

Bracket Socket

Mounting Screw

 

Clamp

Nut

 

 

 

Screw

 

 

Swivel Ball Mount

 

 

Sensor

 

 

Installing Motion Sensor

Check Operation and Adjustment

Note: When first turned on or when switching modes wait 30 seconds.

Locate the RANGE control and ON-TIME control on the motion sensor:

•Indoor Motion Sensor - The RANGE control and ON-TIME control are located inside the battery compartment on the front of the sensor. To set the RANGE or ON-TIME control, remove battery compartment cover by sliding the cover down.

•OutdoorMotionSensor -TheRANGEcontrolandON-TIMEcontrol are located on the bottom of the sensor. Using your fingernails or a small, flat-head screwdriver, gently pry the cover until it opens.

1.Check Operation. Set the ON-TIME control to TEST mode. Walk in frontofsensorunit.TheLEDindicatorlightshouldflashwhenmotion is detected (see illustration, page 8, for location of LED light).

2.Adjust Sensor. Turn the RANGE control to the mid position and ON-TIME control to the TEST position. Walk through coverage area noting where you are when the LED begins to flash. Loosen the clamp screw and move the sensor to change the coverage area. Tighten clamp screw when finished. Do not overtighten clamp screw.

Continued

598-1116-10

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Example 1 Code Settings, System FeaturesCode Settings Example 2 Code Settings, SystemIndoor Plug-In Converter Code Switch LocationsRemote Control Add-A-Switch Entry Switch Lamp Socket Converter FloodlightFunction Controls Remote ControlRear View of Remote Control Optional Car Visor Clip IncludedAdd-A-Switch Removing Battery Tab Add-A-SwitchInstallation Battery ReplacementImportant Considerations Entry SwitchMounting Configurations and Possible Directions Movement Battery ReplacementBattery Compartment Indoor and outdoor Wireless Motion SensorSelect Night or 24 Hour Mode Installing BatteriesInstalling Outdoor Motion Sensor Installing Indoor Motion Sensor Directly To WallCheck Operation and Adjustment Motion Sensor Controls Adjusting Outdoor Motion Sensor CoverageOutdoor Motion Sensor Coverage Area Indoor and Outdoor Motion Sensor SensitivitySpeaker Receiver InformationIndoor Plug-In Converter Lamp socket converterFloodlight Install fixture in accordance with local codesJunction box ground wire to green Ground screw on fixture Wiring FloodlightRegulatory Information Troubleshooting GuideTechnical Service No Service Parts Available for this ProductTWO Year Limited Warranty Ejemplo 2 Calibraciones del código, sistema CaracteristicasCalibraciones DEL Código Ejemplo 1 Calibraciones del código, sistemaConvertidor enchufable para usarse Bajo techo Ubicaciones DE LOS Interruptores DE Circuito ImpresoTornillo TapaVista posterior del control remoto Control remotoPresilla opcional del visor del carro incluida Controles de las funcionesReemplazo de la batería Interruptor a añadibleInstalación OperaciónConsideraciones importantes Interruptor DE EntradaCompartimento de la batería Seleccione modo nocturno o modo de 24 horasInstalación de las baterías ControlTornillo de Montaje De montajeTornillo de la Abrazadera Montura giratoria de bola MovimientoDetector de movimiento para uso exterior Los controles Instalación del detector de movimiento para uso ExteriorRevisión de la operación y de la regulación Instalación del detector de movimientoApunte el detector Controles del detector de movimientoUbicación de los controles Información DEL ReceptorConvertidor enchufable para Usarse bajo techo Convertidor del zócalo de la LámparaCableado del reflector ReflectorNegro EmpaqueNo hay piezas de servicio disponibles para este producto Guía de Análisis de AveríasServicio Técnico Información RegulatoriaGarantía Limitada a 2 Años Exemple 2 Réglage des codes, système CaractéristiquesRéglage DES Codes Exemple 1 Réglage des codes, SystemTélécommande Interrupteur d’appoint Interrupteur d’entrée Emplacement DES MICRO-INTERRUPTEURSPince de pare-soleil d’automobile facultative Comprise TélécommandeCommandes des fonctions Vue arrière de la télécommandeRetrait de l’onglet de la pile Remplacement de la pileInterrupteur d’appoint FonctionnementDétails importants Interrupteur D’ENTRÉETournevis plat Retrait de l’onglet de pileCompartiment des piles Sélection du mode de nuit ou du mode 24 heuresInstallation des piles Détecteurs DE Mouvement Sans FIL Intérieurs ET ExtérieursDétecteur de Important Serrer à la main seulement, ne pas trop serrerVérification du fonctionnement et du réglage Installation du détecteur de mouvements extérieurInstallation du détecteur de mouvement Commandes du détecteur de mouvementZone de couverture du détecteur de mouvements extérieur Zone de couverture du détecteur de mouvements intérieurMouvementMouvement Haut-parleur Informations SUR LE RécepteurConvertisseur enfichable intérieur Convertisseur de douille ’ampouleNoir à noir ProjecteurCâblage du projecteur Aucune pièce de rechange n’est disponible pour ce produit Service TechniqueGuide DE Dépannage Renseignements de règlementsGarantie Limitée DE 2 ANS Çais fran 598-1116-10

598-1116-10 specifications

The Heath Zenith 598-1116-10 is an advanced motion-sensing outdoor light designed to enhance security and functionality around homes and businesses. This fixture is engineered with the latest technologies to provide reliable performance while ensuring energy efficiency and ease of use.

One of the main features of the 598-1116-10 is its state-of-the-art motion sensor. The device employs a passive infrared (PIR) technology that detects movement within a significant range, ensuring that any motion in its monitored area triggers the light. The sensor is adjustable, allowing users to customize the detection range and sensitivity to suit their specific environment. This adaptability is crucial for minimizing false alarms from unwarranted movements, such as passing cars or animals.

In addition to its motion-detection capabilities, the Heath Zenith 598-1116-10 offers various lighting options. The fixture is equipped with a powerful LED light source that produces a bright output while consuming less energy than traditional incandescent bulbs. This not only aids in lowering electricity costs but also contributes to a longer lifespan for the light, reducing the frequency and hassle of bulb replacements.

The design of the 598-1116-10 reflects both aesthetic appeal and functional robustness. The weather-resistant construction ensures that the light can withstand various climatic conditions, making it suitable for installation in different outdoor environments. The sleek and modern design complements a wide range of architectural styles, enhancing the property’s overall curb appeal.

Another important characteristic of this outdoor security light is its convenient operating features. The device includes a manual override option, allowing homeowners to keep the light on continuously for extended periods when needed, such as during gatherings or outdoor events. Additionally, the light can be set to operate on a timer, providing flexibility and control over illumination schedules.

In conclusion, the Heath Zenith 598-1116-10 stands out in the outdoor lighting market due to its motion-sensing technology, energy-efficient LED lighting, durable design, and user-friendly features. It serves not only as a means of illumination but also as a crucial security element, helping to deter potential intruders while offering peace of mind for property owners. This combination of practicality and style makes the 598-1116-10 a top choice for those looking to enhance their outdoor lighting system.
Top Page Image Contents