Dish Network Solo 301 manual Safety

Page 4

Safety

Note to Satellite TV System Installer: This reminder is provided to call the satellite TV system installer’s attention to Article 820-40 of the National Electrical Code (NEC) that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building as close to the point of cable entry as practical.

 

 

 

 

 

 

 

 

Satellite Dish

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Coaxial Cable

 

 

 

 

 

 

 

 

 

Ground Clamp

 

 

 

 

 

 

from Satellite Dish

 

 

 

 

 

 

 

Electric Service Equipment

 

Antenna Discharge

 

 

 

 

 

 

Ground Clamps

 

Unit

 

 

 

 

 

 

Power Service Grounding

 

 

 

 

 

 

 

 

Grounding Conductors

 

 

 

 

 

 

Electrode System

 

 

 

 

 

 

(NEC Art. 250, Part H)

(NEC Section 810-21)

 

 

 

 

 

 

 

 

Safety Tips

Unplug the receiver from the AC power outlet before cleaning.

The use of accessories or attachments not recommended by the receiver manufacturer will void the Limited Warranty.

Do not place the receiver in an enclosure such as a cabinet without proper ventilation.

Do not install the receiver in any area where the temperature can be less than 40°F or more than 113°F.

Do not stack the receiver on top of or below other electronic devices.

Do not place candles or other meltable objects on top of the receiver.

Operate the receiver using only the type of power source indicated on the marking label. Unplug the receiver power cord by gripping the power plug, not the cord.

Do not overload wall outlets or extension cords, as this can result in a risk of fire or electrical shock.

Never insert objects of any kind into the receiver through openings, as the objects may touch dangerous voltage points or short out parts. This could cause fire or electrical shock.

Make sure that the outdoor parts of the antenna system are grounded in accordance with local, state, federal, and National Electrical Code (NEC) requirements.

Do not locate the antenna near overhead light or power circuits, or where it can fall into such power lines or circuits. When installing the antenna, take extreme care to avoid touching such power lines or circuits, as contact with them can be fatal.

Do not attempt to service the receiver yourself, as opening or removing covers may expose you to dangerous voltage, and will void the Limited Warranty. Refer all servicing to authorized service personnel.

Use an outlet that contains surge suppression or ground fault protection. For added protection during a lightning storm, or when the receiver is left unattended and unused for long periods of time, unplug the power cord from the wall outlet, disconnect the lines between the receiver and the antenna, and disconnect the telephone line. This will provide some protection against damage caused by lightning or power line surges.

Page iv

Image 4
Contents Contents Contents Safety Instructions Safety Overview Welcome to Dish NetworkConventions Used in this Guide If YOU Need More Assistance Quick Start GuideOrdering Your Programming To Order ProgrammingAbout Satellite Television Finding Programs To WatchFinding Programs to Watch Rain and Snow Fade Satellite Signal QualitySolar Interference Parts of the System Front Panel Back PanelRemote Control Batteries Remote ControlParts of the System Remote Control Using the Remote Control in SAT ModeUsing the Remote Control in TV Mode Using the Remote Control in VCR Mode Changing the Remote Control Address Satellite Video Recovery Remote Control ModesControl Other Devices with the Remote Control Other Devices with the RemoteLimited Mode SET UP the Remote ControlScan for Device Codes Down Arrow button repeatedly until the device turns off Check the Device CodesControl a Tuner or Amplifier AUX Mode Button Power ButtonVolume Button Select ButtonTo switch back to TV volume control, do the following Using TV or Amplifier Volume ControlMenus MenusMain Menu Program GuideFavorites Lists Menu Theme Categories MenuSystem Locks Menu Timers Menu System Setup MenuBrowse Banner Installing the Receiver in AN Existing System Installing the Receiver in an Existing System Chapter Using the Menus Changing ChannelsOpening the Menus Closing the MenusHighlighting a Menu Option Selecting a Menu OptionLists of Choices in the Menus Highlighting a Choice in a Menu ListUsing the Menus Canceling a ProcedureUsing the Program Guide Using the Program Guide Opening the Program GuideSelecting a Program in the Program Guide Closing the Program GuideUsing the Program Banner Using the Browse BannerUsing the Browse Banner Ordering PAY PER View Programs Using ThemesThemes Using Search Using SearchDish Home Interactive TV Applications Using Favorites Lists Using Favorites ListsCreating or Changing a Favorites List Making a Favorites List Active Changing the Name of a Favorites ListUsing Timers Using TimersEvent Timer Types Event Timer FrequenciesBefore AN Event Timer Operates Setting UP AN Automatic Event TimerSelect the Create option to save the event timer Setting UP a Manual Event TimerOverlapping Event Timers Quick RecordMaximum Number of Event Timers Editing AN Event TimerReviewing Event Timers Deleting AN Event TimerCreating VCR Event Timers Power OFF and Event Timers LOCKS, BLACKED-OUT PROGRAMS, and Event TimersSetting UP the Receiver and VCR to USE a VCR Event Timer Using Locks HOW to SET Locks a TWO Step ProcessWhen YOU have Locked the Receiver Using LocksCreating a Password Creating or Changing Rating Content Code Locks Creating or Changing Channel Locks Locking the ReceiverUnlocking the Receiver Locking the Receiver Front Panel Control ButtonsUnlocking the Receiver Front Panel Control Buttons Locking PAY PER View ProgramsHiding Adult Channels Changing the Receiver PasswordOpening a Locked ITEM, or Opening the Locks Menu Using Caller ID Using Caller IDCaller ID Screens To Turn the Caller ID on and OFF Changing Program Languages Changing Program LanguagesChanging Menu Languages Using Troubleshooting Tools Resetting the Receiver to Factory Default SettingsResetting Your Receiver Diagnostics Using Troubleshooting ToolsPoint Dish and Check Switch Chapter Troubleshooting Tables ReferenceReference ON-SCREEN MessagesTroubleshooting Tables 078, 079 Dishpro Twin LnbfUsing the Remote Control What Is Possible Reason What to Do HappeningHearing a Program Watching a ProgramUsing the Program Guide or the Browse Banner Using the MenusUsing Locks Using Favorite Lists Changing ChannelsUsing the Telephone for Voice /DATA /FAX Troubleshooting TablesBuying a PAY PER View Program Using Event Timers View event You try to set up an eventTV Codes Device CodesVCR Codes Device Codes DVD Player CodesTUNER/AMPLIFIER Codes Tuner Codes AmplifierChapter Chapter 015 Dishpro Twin Lnbf Using the Remote Control Hearing a Program Using the Menus Changing Channels Buying a PAY PER View Program Using Event Timers TV Codes MTC TV/VCR Combo Codes DVD Player Codes DVD/VCR Combo Chapter Index Index Index Index 143334 What the Warranty Covers Limited WarrantyWhat the Warranty does not Cover If YOU Need Assistance Legal LimitationsAdvance Exchange Program Residential Customer Agreement Accessory WarrantyPost Receipt Exchange Program Dish Network Service Billing Policies and Payments for Services Cancellation of Service Equipment Leased Equipment Transfer of ACCOUNT, Services or Equipment FCC Compliance Telephone CommunicationFCC Compliance Compliance Information StatementAppendix