Kathrein UFD 520 Sound settings, Setting the volume, Stereo and two-channel sound reproduction

Page 23

Sound settings

Setting the volume

Set the required volume level by pressing

the ￿￿buttons on the remote control of the receiver. A bar indicator is displayed

on the screen to show the set volume.

Stereo and two-channel sound reproduction

The channel identifier, which you can display by pressing the ￿button, shows the set sound reproduction. (Depending on the direction of the symbolised sound waves – under the displayed time – mono left, mono right or stereo can be set. The digit indicates the number of transmitted sound channels). The programme title is shown in the box on the right.

Press the ￿button to call up the audio menu for sound and language selection. You can now make the required settings, e.g. language selection, provided the cor- responding data is contained in the reception signal (sound track), Dolby Digital (5.1 CH). Select the menu points by

pressing the ￿￿buttons and

select the required setting with the ￿￿buttons. Press the ￿button once again to exit the menu.

AC3

The receiver can process sound transmissions in AC3 format (Dolby Digital) providing you with the opportunity of listening to cinema sound quality in your living room. The digital sound output is provided for this purpose. You will need to con- nect it to a corresponding system.

Please refer to the instructions manual of your Dolby Digital system.

In order to reproduce the AC3 format, set your receiver in the audio menu under "stereo" to “2 of 2" or "2 of 2 (2ch)". The corresponding transmission – "5.1 Ch" (5 channels + 1 subwoofer channel) is then indicated at “Dig. output”.

If AC3 format is not transmitted, you will only be able to select the standard stereo or mono settings or select the broadcast language.

Mute

Press the ￿button on the remote control to mute the sound. This symbol ￿appears on the screen.

Press the ￿button again to restore the sound. The standard volume display bar is then shown for several seconds.

Although you can change the programme while in mute mode, it will remain muted until this mode is cancelled or you correct the volume.

23

Image 23
Contents Operating Manual Page Important Notes PrefaceContents Oscillator frequency L.O Changing the oscillator frequency Transponder selection Safety instructions Mains voltage Place of installationVentilation Humidity, exposure to sunlight, heatView of rear panel Controls, displays and connectionsView of front panel Remote control handset keys Receiver on the command set Command of the remote controlAlphanumeric entries Operating instructionsMenu concept Button functionsLanguage selection OSD Sat if connection Presetting receiving systemConnection and start-up To connect receiverAudio connection Inserting batteries in the remote controlLNB-supply voltage TV and video recorder connectionFirst steps First time installationFactory setting of receiver Important screen displays Radio channel indicatorError message TV programme list On screen displaysRadio programme list Reception status digital Programme selectionSelecting a TV programme Reception status analogue Switching over to radio programmeSelecting a radio programme by number entry Reception status radioVPS-Signal Timer settingsMute Sound settingsSetting the volume Stereo and two-channel sound reproductionFavourite programmes Programme list TV/radioSelecting TV/radio programmes last received To delete a programme Programme assortmentTo add a programme manually Analogue programme list To add analogue programmesAdding/removing satellites Setting up a satelliteTo remove a satellite To enter a satellite nameFull EPG EPG timer programmingProgramme overview Parental lock PasswordFactory setting Entering a passwordPassword Backup operation System parameters Setting system parametersScreen Summer timeTV type Picture formatOSD trans Oscillator frequency L.O LNB configurationChanging the oscillator frequency Installation menuSatellite search DiSEqC settingAntenna settings Transponder selection TP set-up/searchAll new programmes are added to the existing programme list DiSEqC UFO Set-upHigh/Low Pre-programming is not deleted with Reset Video menu Analogue settingDecoder HDP ModeAudio mode Audio menuDe-emphasis Frequency left/rightBandwidth Playback Video recorder connectionRecording Path must be set to external refer to section Video menu Analogue decoder connection„Display info Software and programme lists updateTransferring operating software Data transfer from receiver to receiverPreparation Transferring programme listsTechnical annex Technical featuresTechnical data Scart socket assignments AccessoriesSwitchover VHS/S-VHS Connection arrangement Connection examplesBrückeund DVB Glossary, abbreviationsAC3 Short technical lexiconShort technical lexicon DiSEqC menu ServiceSatellite 998.6248/1001/ZWT Subject to technical modifications