GE 0150-0193G manual Camera Inputs, Composite Monitor Output, Alarm I/O Port

Page 10

14.RS485 Port 2 Connector: For connecting to keyboard and other RS485 devices.

15.RS232 Port 2: For Event Generation and ASCII Text insertion.

Camera Inputs

There are two BNC jacks for each camera. Either jack can receive a camera signal. The signal is looped (directly connected to the other jack), making the camera signal available to other equipment.

The camera input connectors are Auto Terminating.

Cable: 75-Ohm Coaxial

Connectors: BNC

Auto Terminating: Yes

Passive Looping: Yes

This means that the input signal will automatically be terminated with 75-Ohms unless a 2nd cable is connected to the 2nd BNC connector of the same camera input. Make sure there is 75-Ohm termination at the end of the video line if the signal is looped through the DVMRe Triplex.

Time base correction is performed during digital capture. As a result, cameras do not require synchronization.

See section 3.14 for information about disabling unused camera jacks in the menu system.

Composite Monitor Output

When connecting directly from the DVMRe Triplex to the monitor, select the 75-Ohm impedance setting on the monitor.

Cable: 75-Ohm Coaxial

Connectors: BNC

If an additional device is connected to the monitor’s looping output, set the termination of the additional device as 75-Ohm, and set the termination of the monitor as Hi-Z (High Impedance).

Y/C Monitor Output

Y/C video output has a 4-pin mini-DIN style connector. This style of connection is also referred to as SVHS and S-Video.

Cable: 75-Ohm Coaxial

Connectors: BNC

Alarm I/O Port

The back panel of the unit is equipped with an Alarm

Port (DB-25 style connector).

Do not attempt to wire directly to the DB-25	DB-25 Connector on Back Panel
connector on the back panel.

Connect the Alarm PCB (supplied with the unit) to the Alarm Port. Wire all alarm inputs to the Alarm PCB per the pin out specifications shown below.

0150-0193G

10

DVMRe Triplex

Image 10

Contents DVMRe Triplex 0150-0193G / April Contents Searching AlarmsRS232 Remote Control Protocol WebBrowser11Warranty and Service 10Macro TablesDVMRe Triplex Overview Products Featured In This ManualFeatures Product DescriptionPasswords Default Passwords Four-Channel UnitsUnpacking Installation EnvironmentPackage Contents Ten and Sixteen-Channel UnitsAssociated Equipment Back PanelComposite Monitor Output Alarm I/O PortCamera Inputs Monitor OutputAlarm PCB Alarm InputNormally Open and Normally Closed Connections AUX Port Alarm Relay OutputExternal Alarm Acknowledge Input Voltage 30V MaxRJ-45 Pin Configuration For RS485 Port RS485 ConnectorEthernet Port Scsi Port RJ-45 Pin Configuration For Ethernet PortIeee 1394 Firewire Port Gender on unit FemaleRJ-45 Pin Configuration For RS232 Port Power-UpDB-9 Pin Configuration For Port RS232 PortCheck Video Input Quality Minimum Recommended Menu SetupPower-up procedure Check Record And Playback QualityFront Panel DMVRe Triplex Basic OperationsPrincipal Operating Modes Play Forward Button Begins PlaybackLive Viewing Playback Stop Button Stop PlaybackSearching Recorded Data Sequence Button Number ButtonMonitor Displays During Recording RecordingRecord Button Active Cameos Entering Active Cameo ModeDisplay Options Available Multiscreen DisplaysSelecting Cameras Returning To The Default Sequence ListSequencing Dwell TimeStatus Indicators On-screen IndicatorsChanging Position And Color Of Title And Status Indicators Sequencing In CameosStatus Display Box Triplex ModeConditional Indicators ATM/POS Text DisplayStop Reverse Play Button Jog / Shuttle Freeze Button Stop ButtonNumber Button Sequence Button Print Image FeatureZoom and Function Button Equipment Printer SetupConditions Menu Notation In This Manual Accessing The Menu SystemMenu System Overview Available MenusMenu Shortcuts Menus In This ManualNavigating The Menu System Opening the Drop Down Menus Rotate the JogMain Menu Overview Main MenuTime/Date Main Menu → Time/Date → Time / Date DisplayMain Menu → Time/Date → Set Date Main Menu → Time/Date → Set Date FormatMain Menu → Time/Date → Set Master / Slave Main Menu → Time/Date → Network Time Setup Main Menu → Time/Date → Set RegionMain Menu → Sequencing → Multiscreen Dwell RecordMain Menu → Sequencing → Fullscreen Dwell Main Menu → Record → Record Quality Main Menu → Record → Record TimerMain Menu → Record → Event Settings Record Quality Picture Quality Disk Space NeededMain Menu → Record → Timelapse Record Rate Camera 1 0.40 pps 2.5 sppMain Menu → Record → Event Record Rate Main Menu → Record → Activity Record RateMain Menu → Record → Alarm Record Rate Disk Test Setup Menu Main Menu → Record → Record ModeMain Menu → Record → Disk Maintenance No OverwriteDisable Main Menu → Record → Record LockMain Menu → Alarms → Input Configuration AlarmsMain Menu → Record → Auto Delete Mode Should not be the only alarm device on siteMain Menu → Alarms → Alarm Latch Main Menu → Alarms → Alarm ActionMain Menu → Alarms → Alarm History Main Menu → Alarms → Alarm Record ModeMain Menu → Alarms → Enable / Disable ∙ Enable All ∙ Disable AllMain Menu → Alarms → Relay Configuration Main Menu → Alarms → Link To a MacroMain Menu → Alarms → Fullscreen Alarm Main Menu → Alarms → Buzzer SetupMain Menu → Alarms → Notification Main Menu → Alarms → Videoloss ActionMain Menu → Alarms → Pre Alarm Duration Email Notification SetupTCP/IP Notification Setup EnableMacro Main Menu → Alarms → Archive AlarmsMain Menu → Macro → Macro Record Macro Excluded Features Main Menu → Macro → Timed Macro StartRunning a Macro Motion DetectionMain Menu → Macro → Edit Submacro Daylight Savings Time Alternate MethodMain Menu → Motion Detection → Setup Parameters Main Menu → Motion Detection → Enable/Disable DetectionIndividual Enable Menu Activity Detection SetupMain Menu → Motion Detection → Setup Active Zones Intrusion Detection SetupActivity Grid Setup Screen Sensitivity Scope Camera SetupMain Menu → Camera Setup → Camera Titles Main Menu → Motion Detection → Indicate DetectionEdit Titles Main Menu → Camera Setup → AGCTitles Display Camera Title Edit MenuPower Up Disable Main Menu → Camera Setup → Camera DisableIndividual Disable Auto Disable NowMain Menu → Camera Setup → MonB Svhs Main Menu → Camera Setup → Camera ScopeLuminance Histogram Archive Setup Audio SetupMain Menu → Communications → RS232 Pots SetupCommunications PortBaud Rate Main Menu → Communications → RS485Main Menu → Communications → Ethernet Settings Front Panel Lock Factory SettingsReturn To Factory Defaults Change LanguageActivate The Ethernet Password Changing the Installer or Operator PasswordsEthernet Password Deactivate The Ethernet PasswordQuickInstall Menu Item Primary Menu Location Section Manual QuickInstall MenuQuickInstall Menu Overview Operator MenuSystemView Menu Overview SystemView MenuOperator Menu Item Primary Menu Location Section Manual View Screens View Screen∙ Event Associated Cameras Up to Record TimerRecord Rate ∙ On/Off On or Off∙ Time Zone GMT+0000 ∙ QuickWave CD Write On or Off ∙ Network Address∙ Keyboard Lock On or Off ∙ Record Lock On or Off ∙ Http Port 80Alarm Output AlarmsAlarm Input Alarm AcknowledgeLive Alarms Displays Alarm Operations During PlaybackMonitor-B Display During Alarm Channel UnitsSearching For Recorded Alarms Alarm History BoxRecorded Alarms Searching Search Menu OverviewQuick Archive to CD Disk Analysis ScreenSearch Button Motion Search Function ButtonSearch Filters Selecting Search ParametersText File Format Retail SearchUploading/Downloading the retailsearch .txt File Local Retail Search Screen Date MM/DD/YY Time HhmmRestrictions and Limitations Search ResultsActivate Search Activity, Text, Motion, Alarm Search Results To access the web interface WebBrowserMain Viewing Area WaveBrowser Overview and Controls∙ The Main Viewing Area The large blue area Drop Down Volume List Box Button PanelFunctionality DVMRe Triplex WaveLinkName Code Description Example Email Links Connections Technical SpecificationsGeneral VideoMotion Detection AudioPart Numbers Message Structure Message TypeAlarm/Event Fields Alarm ActionsStart Event 0000 0001b Event ActionsNo Event Change 0000 0000b Stop Event 0000 0010bData Structure Front Panel Button EmulationDescription Configuration and Status Data structureMacro Functions Table Macro TablesMacro Description Number Scheduled Macro Table Event Day Time Macro to RunFactory Service Warranty and ServiceFactory Address Warranty and Return Information Advance Replacement Policy0150-0193G