GE 0150-0193G manual Alarm/Event Fields, Alarm Actions

Page 86

8.3 Alarm/Event Fields

The two least significant bits are currently used for the Event commands. Bits 2 and 3 are used for the Alarm commands.

MSB						LSB
7	6	5	4	3	2	1 0

Event Start

Event Stop

Alarm Start

Alarm Stop

8.4 Alarm Actions

No Alarm Change – 0000 00XXb

If both the start and stop bits are clear, the alarm status and camera record rates will remain unchanged.

Start Alarm – 0000 01XXb

If only the start bit is set, the DVMRe will enter the Alarm mode. The selected camera will become the alarm camera. Pre-alarm video will be recorded and the Alarm Record Rate will be initiated.

NOTE

Every Start Alarm command should subsequently be followed with a Stop Alarm command at some point. Failure to do so will render that alarm input useless, even if the alarm was latched and gets acknowledged from the front panel. A Stop Alarm followed by a Start Alarm will have to be sent to create a new alarm on that channel.

Stop Alarm – 0000 10XXb

If only the stop bit is set, the selected camera’s alarm status will be cleared. If no other alarms are present, the DVMRe will exit the alarm mode.

Momentary Alarm – 0000 11XXb

If both the start and stop bits are set, a momentary alarm will be initiated on the selected camera. Pre- alarm video will be recorded at the alarm record rate, after which the DVMRe will continue to record video at the normal record rate.

0150-0193G

86

DVMRe Triplex

Image 86

Contents DVMRe Triplex 0150-0193G / April Contents Searching AlarmsRS232 Remote Control Protocol WebBrowser11Warranty and Service 10Macro TablesDVMRe Triplex Overview Products Featured In This ManualFeatures Product DescriptionPasswords Default Passwords Four-Channel UnitsUnpacking Installation EnvironmentPackage Contents Ten and Sixteen-Channel UnitsAssociated Equipment Back PanelComposite Monitor Output Alarm I/O PortCamera Inputs Monitor OutputNormally Open and Normally Closed Connections Alarm InputAlarm PCB AUX Port Alarm Relay OutputExternal Alarm Acknowledge Input Voltage 30V MaxEthernet Port RS485 ConnectorRJ-45 Pin Configuration For RS485 Port Scsi Port RJ-45 Pin Configuration For Ethernet PortIeee 1394 Firewire Port Gender on unit FemaleRJ-45 Pin Configuration For RS232 Port Power-UpDB-9 Pin Configuration For Port RS232 PortCheck Video Input Quality Minimum Recommended Menu SetupPower-up procedure Check Record And Playback QualityFront Panel DMVRe Triplex Basic OperationsPrincipal Operating Modes Play Forward Button Begins PlaybackLive Viewing Playback Stop Button Stop PlaybackSearching Recorded Data Sequence Button Number ButtonRecord Button RecordingMonitor Displays During Recording Active Cameos Entering Active Cameo ModeDisplay Options Available Multiscreen DisplaysSelecting Cameras Returning To The Default Sequence ListSequencing Dwell TimeStatus Indicators On-screen IndicatorsChanging Position And Color Of Title And Status Indicators Sequencing In CameosStatus Display Box Triplex ModeConditional Indicators ATM/POS Text DisplayStop Reverse Play Button Jog / Shuttle Freeze Button Stop ButtonZoom and Function Button Print Image FeatureNumber Button Sequence Button Conditions Printer SetupEquipment Menu Notation In This Manual Accessing The Menu SystemMenu System Overview Available MenusMenu Shortcuts Menus In This ManualNavigating The Menu System Opening the Drop Down Menus Rotate the JogMain Menu Overview Main MenuTime/Date Main Menu → Time/Date → Time / Date DisplayMain Menu → Time/Date → Set Master / Slave Main Menu → Time/Date → Set Date FormatMain Menu → Time/Date → Set Date Main Menu → Time/Date → Network Time Setup Main Menu → Time/Date → Set RegionMain Menu → Sequencing → Fullscreen Dwell RecordMain Menu → Sequencing → Multiscreen Dwell Main Menu → Record → Record Quality Main Menu → Record → Record TimerMain Menu → Record → Event Settings Record Quality Picture Quality Disk Space NeededMain Menu → Record → Timelapse Record Rate Camera 1 0.40 pps 2.5 sppMain Menu → Record → Event Record Rate Main Menu → Record → Activity Record RateMain Menu → Record → Alarm Record Rate Disk Test Setup Menu Main Menu → Record → Record ModeMain Menu → Record → Disk Maintenance No OverwriteDisable Main Menu → Record → Record LockMain Menu → Alarms → Input Configuration AlarmsMain Menu → Record → Auto Delete Mode Should not be the only alarm device on siteMain Menu → Alarms → Alarm Latch Main Menu → Alarms → Alarm ActionMain Menu → Alarms → Alarm History Main Menu → Alarms → Alarm Record ModeMain Menu → Alarms → Enable / Disable ∙ Enable All ∙ Disable AllMain Menu → Alarms → Relay Configuration Main Menu → Alarms → Link To a MacroMain Menu → Alarms → Fullscreen Alarm Main Menu → Alarms → Buzzer SetupMain Menu → Alarms → Notification Main Menu → Alarms → Videoloss ActionMain Menu → Alarms → Pre Alarm Duration Email Notification SetupTCP/IP Notification Setup EnableMain Menu → Macro → Macro Record Main Menu → Alarms → Archive AlarmsMacro Macro Excluded Features Main Menu → Macro → Timed Macro StartRunning a Macro Motion DetectionMain Menu → Macro → Edit Submacro Daylight Savings Time Alternate MethodMain Menu → Motion Detection → Setup Parameters Main Menu → Motion Detection → Enable/Disable DetectionIndividual Enable Menu Activity Detection SetupActivity Grid Setup Screen Intrusion Detection SetupMain Menu → Motion Detection → Setup Active Zones Sensitivity Scope Camera SetupMain Menu → Camera Setup → Camera Titles Main Menu → Motion Detection → Indicate DetectionEdit Titles Main Menu → Camera Setup → AGCTitles Display Camera Title Edit MenuPower Up Disable Main Menu → Camera Setup → Camera DisableIndividual Disable Auto Disable NowLuminance Histogram Main Menu → Camera Setup → Camera ScopeMain Menu → Camera Setup → MonB Svhs Archive Setup Audio SetupMain Menu → Communications → RS232 Pots SetupCommunications PortBaud Rate Main Menu → Communications → RS485Main Menu → Communications → Ethernet Settings Front Panel Lock Factory SettingsReturn To Factory Defaults Change LanguageActivate The Ethernet Password Changing the Installer or Operator PasswordsEthernet Password Deactivate The Ethernet PasswordQuickInstall Menu Item Primary Menu Location Section Manual QuickInstall MenuQuickInstall Menu Overview Operator MenuOperator Menu Item Primary Menu Location Section Manual SystemView MenuSystemView Menu Overview View Screens View Screen∙ Event Associated Cameras Up to Record TimerRecord Rate ∙ On/Off On or Off∙ Time Zone GMT+0000 ∙ QuickWave CD Write On or Off ∙ Network Address∙ Keyboard Lock On or Off ∙ Record Lock On or Off ∙ Http Port 80Alarm Output AlarmsAlarm Input Alarm AcknowledgeLive Alarms Displays Alarm Operations During PlaybackMonitor-B Display During Alarm Channel UnitsRecorded Alarms Alarm History BoxSearching For Recorded Alarms Searching Search Menu OverviewSearch Button Disk Analysis ScreenQuick Archive to CD Motion Search Function ButtonSearch Filters Selecting Search ParametersUploading/Downloading the retailsearch .txt File Retail SearchText File Format Local Retail Search Screen Date MM/DD/YY Time HhmmActivate Search Search ResultsRestrictions and Limitations Activity, Text, Motion, Alarm Search Results To access the web interface WebBrowser∙ The Main Viewing Area The large blue area WaveBrowser Overview and ControlsMain Viewing Area Drop Down Volume List Box Button PanelName Code Description Example DVMRe Triplex WaveLinkFunctionality Email Links Connections Technical SpecificationsGeneral VideoPart Numbers AudioMotion Detection Message Structure Message TypeAlarm/Event Fields Alarm ActionsStart Event 0000 0001b Event ActionsNo Event Change 0000 0000b Stop Event 0000 0010bDescription Front Panel Button EmulationData Structure Configuration and Status Data structureMacro Description Number Macro TablesMacro Functions Table Scheduled Macro Table Event Day Time Macro to RunFactory Address Warranty and ServiceFactory Service Warranty and Return Information Advance Replacement Policy0150-0193G