GE 0150-0193G manual Main Menu → Alarms → Alarm Latch, Main Menu → Alarms → Alarm Action

Page 42

qMain Menu → Alarms → Alarm Latch

This feature determines how the unit latches alarm conditions.

Select from the following options:

Latched: The alarm is activated until it is silenced and acknowledged by the user.

Transparent: The alarm is active only while receiving alarm input. The alarm condition is canceled when the alarm input ceases.

Latched

Transparent

Timed Out

Timed Out: The alarm condition is latched for the amount of time selected in this menu, then it is automatically silenced and acknowledged. If the alarm input exceeds the duration specified in this menu, the unit silences and acknowledges the alarm when the alarm input ceases. Select the timeout duration, the range is from 1 to 250 seconds.

Transparent alarms cannot be silenced and acknowledged. If transparent mode is preferred, but the ability to silence and acknowledge alarms is desired, select Timed Out and set the Alarm Timeout to two seconds.

qMain Menu → Alarms → Alarm Action

This menu is not available on 4-channel units. Only the full screen alarm display is available on the 4-channel unit. Therefore, a 4 channel unit will always be limited to the default values in this menu, i.e. no presets linked to alarms and alarm relay is always Relay 1.

Input: Select the input you wish to configure.

Freeze: Selecting Yes will freeze the alarm camera display (quadrant 1) at the time the alarm is activated.

Cameras: This setting determines the four cameras displayed on-screen when an alarm is received. The camera group contains the camera in alarm and three associated cameras.

Alarm Action Setup

Input

:

01

Freeze

: Yes

Cameras

: 01

16 02 03

Presets

: 01

-- 09 --

Relay

:

1

 

Intrusion AND/OR:

OR

 

[CANCEL]

[OK]

Default Settings: The first camera in the list is the camera in alarm.

The second camera in the list is the camera that precedes the alarm camera numerically. The third and fourth cameras in the list are the two cameras following the alarm camera numerically.

Preset: Use this feature to send a camera to a preset when an alarm is activated. The preset number corresponds directly with the camera number located directly above it in this menu. Select from 1 through 16. If this field is left blank, the camera will not respond. In the example above, Camera 1 will go to Preset 1, while Camera 2 will go to Preset 9.

Relay: Configure which relay will be triggered when an alarm is activated per camera. Select from:

∙

1

∙

1 + 2

∙

2

∙

None

Intrusion AND/OR: Use this feature to activate alarms by hardwired alarm inputs AND/OR Intrusion detection. Select from AND or OR. Motion Detection must be set to Intrusion and linked to the Alarm number.

Rotate the Jog to navigate and the Shuttle to change the values.

0150-0193G

42

DVMRe Triplex

Page 41 Page 43
Image 42
Page 41 Page 43
Contents DVMRe Triplex 0150-0193G / April Contents Searching AlarmsRS232 Remote Control Protocol WebBrowser11Warranty and Service 10Macro TablesDVMRe Triplex Overview Products Featured In This ManualFeatures Product DescriptionPasswords Default Passwords Four-Channel UnitsUnpacking Installation EnvironmentPackage Contents Ten and Sixteen-Channel UnitsAssociated Equipment Back PanelComposite Monitor Output Alarm I/O PortCamera Inputs Monitor OutputAlarm Input Alarm PCBNormally Open and Normally Closed Connections AUX Port Alarm Relay OutputExternal Alarm Acknowledge Input Voltage 30V MaxRS485 Connector RJ-45 Pin Configuration For RS485 PortEthernet Port Scsi Port RJ-45 Pin Configuration For Ethernet PortIeee 1394 Firewire Port Gender on unit FemaleRJ-45 Pin Configuration For RS232 Port Power-UpDB-9 Pin Configuration For Port RS232 PortCheck Video Input Quality Minimum Recommended Menu SetupPower-up procedure Check Record And Playback QualityFront Panel DMVRe Triplex Basic OperationsPrincipal Operating Modes Play Forward Button Begins PlaybackLive Viewing Playback Stop Button Stop PlaybackSearching Recorded Data Sequence Button Number ButtonRecording Monitor Displays During RecordingRecord Button Active Cameos Entering Active Cameo ModeDisplay Options Available Multiscreen DisplaysSelecting Cameras Returning To The Default Sequence ListSequencing Dwell TimeStatus Indicators On-screen IndicatorsChanging Position And Color Of Title And Status Indicators Sequencing In CameosStatus Display Box Triplex ModeConditional Indicators ATM/POS Text DisplayStop Reverse Play Button Jog / Shuttle Freeze Button Stop ButtonPrint Image Feature Number Button Sequence ButtonZoom and Function Button Printer Setup EquipmentConditions Menu Notation In This Manual Accessing The Menu SystemMenu System Overview Available MenusMenu Shortcuts Menus In This ManualNavigating The Menu System Opening the Drop Down Menus Rotate the JogMain Menu Overview Main MenuTime/Date Main Menu → Time/Date → Time / Date DisplayMain Menu → Time/Date → Set Date Format Main Menu → Time/Date → Set DateMain Menu → Time/Date → Set Master / Slave Main Menu → Time/Date → Network Time Setup Main Menu → Time/Date → Set RegionRecord Main Menu → Sequencing → Multiscreen DwellMain Menu → Sequencing → Fullscreen Dwell Main Menu → Record → Record Quality Main Menu → Record → Record TimerMain Menu → Record → Event Settings Record Quality Picture Quality Disk Space NeededMain Menu → Record → Timelapse Record Rate Camera 1 0.40 pps 2.5 sppMain Menu → Record → Event Record Rate Main Menu → Record → Activity Record RateMain Menu → Record → Alarm Record Rate Disk Test Setup Menu Main Menu → Record → Record ModeMain Menu → Record → Disk Maintenance No OverwriteDisable Main Menu → Record → Record LockMain Menu → Alarms → Input Configuration AlarmsMain Menu → Record → Auto Delete Mode Should not be the only alarm device on siteMain Menu → Alarms → Alarm Latch Main Menu → Alarms → Alarm ActionMain Menu → Alarms → Alarm History Main Menu → Alarms → Alarm Record ModeMain Menu → Alarms → Enable / Disable ∙ Enable All ∙ Disable AllMain Menu → Alarms → Relay Configuration Main Menu → Alarms → Link To a MacroMain Menu → Alarms → Fullscreen Alarm Main Menu → Alarms → Buzzer SetupMain Menu → Alarms → Notification Main Menu → Alarms → Videoloss ActionMain Menu → Alarms → Pre Alarm Duration Email Notification SetupTCP/IP Notification Setup EnableMain Menu → Alarms → Archive Alarms MacroMain Menu → Macro → Macro Record Macro Excluded Features Main Menu → Macro → Timed Macro StartRunning a Macro Motion DetectionMain Menu → Macro → Edit Submacro Daylight Savings Time Alternate MethodMain Menu → Motion Detection → Setup Parameters Main Menu → Motion Detection → Enable/Disable DetectionIndividual Enable Menu Activity Detection SetupIntrusion Detection Setup Main Menu → Motion Detection → Setup Active ZonesActivity Grid Setup Screen Sensitivity Scope Camera SetupMain Menu → Camera Setup → Camera Titles Main Menu → Motion Detection → Indicate DetectionEdit Titles Main Menu → Camera Setup → AGCTitles Display Camera Title Edit MenuPower Up Disable Main Menu → Camera Setup → Camera DisableIndividual Disable Auto Disable NowMain Menu → Camera Setup → Camera Scope Main Menu → Camera Setup → MonB SvhsLuminance Histogram Archive Setup Audio SetupMain Menu → Communications → RS232 Pots SetupCommunications PortBaud Rate Main Menu → Communications → RS485Main Menu → Communications → Ethernet Settings Front Panel Lock Factory SettingsReturn To Factory Defaults Change LanguageActivate The Ethernet Password Changing the Installer or Operator PasswordsEthernet Password Deactivate The Ethernet PasswordQuickInstall Menu Item Primary Menu Location Section Manual QuickInstall MenuQuickInstall Menu Overview Operator MenuSystemView Menu SystemView Menu OverviewOperator Menu Item Primary Menu Location Section Manual View Screens View Screen∙ Event Associated Cameras Up to Record TimerRecord Rate ∙ On/Off On or Off∙ Time Zone GMT+0000 ∙ QuickWave CD Write On or Off ∙ Network Address∙ Keyboard Lock On or Off ∙ Record Lock On or Off ∙ Http Port 80Alarm Output AlarmsAlarm Input Alarm AcknowledgeLive Alarms Displays Alarm Operations During PlaybackMonitor-B Display During Alarm Channel UnitsAlarm History Box Searching For Recorded AlarmsRecorded Alarms Searching Search Menu OverviewDisk Analysis Screen Quick Archive to CDSearch Button Motion Search Function ButtonSearch Filters Selecting Search ParametersRetail Search Text File FormatUploading/Downloading the retailsearch .txt File Local Retail Search Screen Date MM/DD/YY Time HhmmSearch Results Restrictions and LimitationsActivate Search Activity, Text, Motion, Alarm Search Results To access the web interface WebBrowserWaveBrowser Overview and Controls Main Viewing Area∙ The Main Viewing Area The large blue area Drop Down Volume List Box Button PanelDVMRe Triplex WaveLink FunctionalityName Code Description Example Email Links Connections Technical SpecificationsGeneral VideoAudio Motion DetectionPart Numbers Message Structure Message TypeAlarm/Event Fields Alarm ActionsStart Event 0000 0001b Event ActionsNo Event Change 0000 0000b Stop Event 0000 0010bFront Panel Button Emulation Data StructureDescription Configuration and Status Data structureMacro Tables Macro Functions TableMacro Description Number Scheduled Macro Table Event Day Time Macro to RunWarranty and Service Factory ServiceFactory Address Warranty and Return Information Advance Replacement Policy0150-0193G
Top Page Image Contents