GE 0150-0193G manual Event Actions, No Event Change 0000 0000b, Start Event 0000 0001b

Page 87

8.5 Event Actions

NOTE

All Event messages will be ignored while an Alarm condition exists in the DVMRe.

No Event Change – 0000 0000b

If both the start and stop bits are clear, there will be no change to the event status. The camera’s record rate will not be changed.

Start Event – 0000 0001b

If only the start bit is set, an event will be initiated on the selected camera. This will cause the selected camera, as well as any pre-event video to be recorded at the Event Record Rate.

Stop Event – 0000 0010b

If only the stop bit is set, the current event on the selected camera will be terminated. This will start the post-event timer after which, the selected camera will resume recording at the normal record rate.

Momentary Event – 0000 0011b

If both the start and stop bits are set, a momentary event will be initiated on the selected camera. Pre- event video will be recorded at the event record rate for the selected camera. The post-event timer will continue recording at the event record rate, after which the selected camera will resume recording at the normal record rate.

0150-0193G

87

DVMRe Triplex

Image 87
Contents DVMRe Triplex 0150-0193G / April Contents WebBrowser AlarmsRS232 Remote Control Protocol Searching10Macro Tables 11Warranty and ServiceProduct Description Products Featured In This ManualFeatures DVMRe Triplex OverviewDefault Passwords Four-Channel Units PasswordsTen and Sixteen-Channel Units Installation EnvironmentPackage Contents UnpackingBack Panel Associated EquipmentMonitor Output Alarm I/O PortCamera Inputs Composite Monitor OutputAlarm Input Alarm PCBNormally Open and Normally Closed Connections Voltage 30V Max Alarm Relay OutputExternal Alarm Acknowledge Input AUX PortRS485 Connector RJ-45 Pin Configuration For RS485 PortEthernet Port Gender on unit Female RJ-45 Pin Configuration For Ethernet PortIeee 1394 Firewire Port Scsi PortRS232 Port Power-UpDB-9 Pin Configuration For Port RJ-45 Pin Configuration For RS232 PortCheck Record And Playback Quality Minimum Recommended Menu SetupPower-up procedure Check Video Input QualityPlay Forward Button Begins Playback DMVRe Triplex Basic OperationsPrincipal Operating Modes Front PanelLive Viewing Playback Sequence Button Number Button Stop PlaybackSearching Recorded Data Stop ButtonRecording Monitor Displays During RecordingRecord Button Available Multiscreen Displays Entering Active Cameo ModeDisplay Options Active CameosDwell Time Returning To The Default Sequence ListSequencing Selecting CamerasSequencing In Cameos On-screen IndicatorsChanging Position And Color Of Title And Status Indicators Status IndicatorsATM/POS Text Display Triplex ModeConditional Indicators Status Display BoxReverse Play Button Jog / Shuttle Freeze Button Stop Button StopPrint Image Feature Number Button Sequence ButtonZoom and Function Button Printer Setup EquipmentConditions Available Menus Accessing The Menu SystemMenu System Overview Menu Notation In This ManualOpening the Drop Down Menus Rotate the Jog Menus In This ManualNavigating The Menu System Menu ShortcutsMain Menu → Time/Date → Time / Date Display Main MenuTime/Date Main Menu OverviewMain Menu → Time/Date → Set Date Format Main Menu → Time/Date → Set DateMain Menu → Time/Date → Set Master / Slave Main Menu → Time/Date → Set Region Main Menu → Time/Date → Network Time SetupRecord Main Menu → Sequencing → Multiscreen DwellMain Menu → Sequencing → Fullscreen Dwell Record Quality Picture Quality Disk Space Needed Main Menu → Record → Record TimerMain Menu → Record → Event Settings Main Menu → Record → Record QualityCamera 1 0.40 pps 2.5 spp Main Menu → Record → Timelapse Record RateMain Menu → Record → Activity Record Rate Main Menu → Record → Event Record RateMain Menu → Record → Alarm Record Rate No Overwrite Main Menu → Record → Record ModeMain Menu → Record → Disk Maintenance Disk Test Setup MenuMain Menu → Record → Record Lock DisableShould not be the only alarm device on site AlarmsMain Menu → Record → Auto Delete Mode Main Menu → Alarms → Input ConfigurationMain Menu → Alarms → Alarm Action Main Menu → Alarms → Alarm Latch∙ Enable All ∙ Disable All Main Menu → Alarms → Alarm Record ModeMain Menu → Alarms → Enable / Disable Main Menu → Alarms → Alarm HistoryMain Menu → Alarms → Buzzer Setup Main Menu → Alarms → Link To a MacroMain Menu → Alarms → Fullscreen Alarm Main Menu → Alarms → Relay ConfigurationEmail Notification Setup Main Menu → Alarms → Videoloss ActionMain Menu → Alarms → Pre Alarm Duration Main Menu → Alarms → NotificationEnable TCP/IP Notification SetupMain Menu → Alarms → Archive Alarms MacroMain Menu → Macro → Macro Record Main Menu → Macro → Timed Macro Start Macro Excluded FeaturesDaylight Savings Time Alternate Method Motion DetectionMain Menu → Macro → Edit Submacro Running a MacroActivity Detection Setup Main Menu → Motion Detection → Enable/Disable DetectionIndividual Enable Menu Main Menu → Motion Detection → Setup ParametersIntrusion Detection Setup Main Menu → Motion Detection → Setup Active ZonesActivity Grid Setup Screen Main Menu → Motion Detection → Indicate Detection Camera SetupMain Menu → Camera Setup → Camera Titles Sensitivity ScopeCamera Title Edit Menu Main Menu → Camera Setup → AGCTitles Display Edit TitlesAuto Disable Now Main Menu → Camera Setup → Camera DisableIndividual Disable Power Up DisableMain Menu → Camera Setup → Camera Scope Main Menu → Camera Setup → MonB SvhsLuminance Histogram Audio Setup Archive SetupPort Pots SetupCommunications Main Menu → Communications → RS232Main Menu → Communications → RS485 Baud RateMain Menu → Communications → Ethernet Settings Change Language Factory SettingsReturn To Factory Defaults Front Panel LockDeactivate The Ethernet Password Changing the Installer or Operator PasswordsEthernet Password Activate The Ethernet PasswordOperator Menu QuickInstall MenuQuickInstall Menu Overview QuickInstall Menu Item Primary Menu Location Section ManualSystemView Menu SystemView Menu OverviewOperator Menu Item Primary Menu Location Section Manual View Screen View Screens∙ On/Off On or Off Record TimerRecord Rate ∙ Event Associated Cameras Up to∙ Http Port 80 ∙ Network Address∙ Keyboard Lock On or Off ∙ Record Lock On or Off ∙ Time Zone GMT+0000 ∙ QuickWave CD Write On or OffAlarm Acknowledge AlarmsAlarm Input Alarm OutputChannel Units Alarm Operations During PlaybackMonitor-B Display During Alarm Live Alarms DisplaysAlarm History Box Searching For Recorded AlarmsRecorded Alarms Search Menu Overview SearchingDisk Analysis Screen Quick Archive to CDSearch Button Function Button Motion SearchSelecting Search Parameters Search FiltersRetail Search Text File FormatUploading/Downloading the retailsearch .txt File Date MM/DD/YY Time Hhmm Local Retail Search ScreenSearch Results Restrictions and LimitationsActivate Search Activity, Text, Motion, Alarm Search Results WebBrowser To access the web interfaceWaveBrowser Overview and Controls Main Viewing Area∙ The Main Viewing Area The large blue area Button Panel Drop Down Volume List BoxDVMRe Triplex WaveLink FunctionalityName Code Description Example Email Links Video Technical SpecificationsGeneral ConnectionsAudio Motion DetectionPart Numbers Message Type Message StructureAlarm Actions Alarm/Event FieldsStop Event 0000 0010b Event ActionsNo Event Change 0000 0000b Start Event 0000 0001bFront Panel Button Emulation Data StructureDescription Data structure Configuration and StatusMacro Tables Macro Functions TableMacro Description Number Event Day Time Macro to Run Scheduled Macro TableWarranty and Service Factory ServiceFactory Address Advance Replacement Policy Warranty and Return Information0150-0193G