Chariot Carriers Chariot Baby Seat manual View from inside with seat lifted for clarity

Page 49

Illustration A

The easiest way of getting the strap tight is by pulling the end of the strap downwards below the seat.

View from inside with seat lifted for clarity.

Then thread the baby seat strap that faces the middle at the front of the baby seat down

in front of the telescopic tube, around the bungee cord and again back up in front of the telescopic tube.

Thread the end of the strap as shown in the above illustration through the fastener in the baby seat and gently pull the strap tight.

Next, the straps at the rear end of the baby seat are attached.

Then lay the strap that is on the side of the baby seat facing out of the trailer around the vertical frame tube at the side and pull it forward again over the horizontal diagonal tube.

Thread the end of the strap as shown in illustration A through the fastener in the baby seat and gently pull the strap tight.

In the centre of the trailer seat backrest, there are straps for each side for further securing of the baby seat.

Pull the strap pointing to the side chosen through the baby seat fastener and pull it tight as in illustration A.

Finally connect the fastex buckles on the underside of the baby seat with the buckles on the lap belt of the side chosen. Pull the lap belt ends equally tight, so that the baby seat does not tip to one side.

Finally pull all fastening straps tight.

On the Corsaire XL and Captain XL models it is important to ensure that the baby seat is set high enough and under enough tension, so that neither the baby’s bottom nor its back will come into contact with the trailer seat as a result of jolts during travel. Once all straps have been pulled tight, the front padding should sit more or less vertical over the telescopic tube.

Please note: Make sure you check all belt buckles are tight!

49

Image 49

Contents Ab Modelljahr Benutzerhandbuch Gebruikershandleiding Owner‘s manualVanaf bouwjaar Models from 2006 onwardsInhaltsverzeichnis / Inhoud / Table of contents Achtung Produktionsbedingte Änderungen vorbehalten Montageanleitung Chariot BabysitzSicherheitshinweis Lieferzustand HinweisEinbau in die zweisitzigen Chariot-Fahrzeuge Lösen der Befestigungsgurte am BabysitzVorbereitende Schritte Montage der TeleskopstangeAnsicht von vorn AchtungBefestigung in den Modellen Comfort und Cheetah2 Befestigung des BabysitzesUnd ziehen Sie das Gurtband Befestigung in den Modellen Cabriolet, CX2 und Cougar2 Page Seitliche Positionierung Ziehen Sie abschließend alle Befestigungsgurte stramm an Ansicht von innen, Sitz zur Demonstration hochge- klapptMittige Positionierung Befestigung der Sicherheitsgurte Montage der D-Ringe Einbau in die einsitzigen Chariot-FahrzeugeBefestigung im Modell Cheetah1 Page Fertig montierter Babysitz Verletzungen erleiden Befestigung in den Modellen CX1 und Cougar1Page Fertig montierter Babysitz Verletzungen erleiden Bei den Modellen Cheetah1, Cheetah2 und Comfort Anschnallen des Babys und Einstellen der SicherheitsgurtePflegehinweise SicherheitshinweiseFalten der Chariot-Fahrzeuge De baby vastmaken en de veiligheidsgordels afstellen InhoudVeiligheidsaanwijzing Inbouwinstructies Chariot BabyzittingWordt als volgt geleverd OpmerkingMontage in de tweezits Chariot voertuigen De bevestigingsriemen losmakenVoorbereidende stappen Inbouw van de telescoopstangVooraanzicht Montage in de Comfort en Cheetah2 Bevestiging van de babyzittingAfbeelding staat aangegeven… Montage in de Cabriolet, CX2 en Cougar2 …en trek de riem iets aan Montage aan de zijkant Trek daarna alle bevestigingsriemen strak aan Montage in het midden De veiligheidsgordels bevestigen Montage in de éénzits Chariot voertuigen Installatie van de D-ringenMontage in de Cheetah1 Page Bevestiging in de CX1 en Cougar1 Page Volledig ingebouwde babyzitting verwondingen oplopen Voor de Cheetah1, Cheetah2 en Comfort De baby vastmaken en de veiligheidsgordels afstellenVerzorging VeiligheidsaanwijzingenDe Chariot aanhangers opvouwen Table of contents Fitting Instructions Chariot Baby Seat Safety noteParts supplied Baby seat is not designed to be fitted to older modelsFitting to Two Seater Chariot Trailers Undoing the Baby Seat Securing StrapsPreliminary steps Fitting the Telescopic TubeFront view Please noteSecuring on the Comfort and Cheetah2 models Securing the Baby SeatPlease note Make sure you check all belt buckles are tight Securing on the Cabriolet, CX2 and Cougar2 models Page Lateral positioning Finally pull all fastening straps tight View from inside with seat lifted for clarityCentre-positioning Securing the safety belts Fitting the D-rings Fitting to Single Seater Chariot TrailersSecuring on the Cheetah1 model Page Fully fitted baby seat Event of an accident Securing on the CX1 and Cougar1 modelsPage Fully fitted baby seat Event of an accident On the Cheetah1, Cheetah2 and Comfort models Fastening the Baby and Adjusting the Safety BeltsCare of the Baby Seat Safety InstructionsFolding the Chariot Carriers