steps shown in Figures 2 and 3.
•To fold up the Pliko P3 Naked stroller, loosen the hood braces, lift the backrest, and repeat the steps shown in Figures 13, 14, and 15.
ADJUSTING THE FOOTBOARD
40• The footboard can be adjusted to three positions. To lower the footboard, pull the two side levers downwards. To lift the footboard, pull it upwards until it clicks into place.
REAR FOOTBOARD
41• The rear footboard helps the mother to push the stroller over small bumps, and can be used to carry a second child.
LOADING
42• To use the Pliko P3 Naked with two children, first set the brakes on the stroller. Next place the smaller child in the seat and fasten the safety belt
(1). Hold the handlebars (2) and have the second child stand on the rear footboard (3).
•Never leave your children alone in the stroller.
•Do not allow a child to stand on the rear footboard when the stroller is empty.
HOOD
•The hood has a zipper for attaching the rain canopy.
43• To attach the hood, push the fasteners downwards until they click into place, as shown in the figure.
44• Button the hood to the inside of the armrests and to the backrest on the stroller, as shown in the figure.
45• To open the hood, push the braces downwards. The hood can be lowered along with the reclining backrest.
46• It is possible to detach the back part of the fabric by unzipping it and use the hood as a sun canopy.
47• To reattach the back part of the fabric, proceed as indicated in the figure.
48• By lowering the stroller backrest, the hood extends and, thanks to the double zipper, a window can be created to allow more air to circulate and see the child when sleeping.
49• To remove the hood, unbutton it from the stroller and loosen the braces. Lift the tabs on the fasteners by pressing towards the inside of the stroller.
COVER
50• To fasten the cover to the stroller, zip it onto the footboard as shown in the figure.
RAIN CANOPY
51• To attach the rain canopy, zip it to the hood. 52• Fasten the button found on the elastic to the
stroller button until you hear a click, as indicated in the figure.
53• Fasten the elastic on the bottom of the rain canopy to the wheel.
54• The practical rain canopy can be lowered by opening the zipper; it will remain fastened to the stroller by the elastic.
55• This rain canopy has been designed for use with the Primo Viaggio car seat fastened on the stroller as well, to guarantee your child total protection.
•Do not use the rain canopy in closed places. Always check from time to time to make sure the child is not too hot.
•Do not place the PVC rain canopy near sources of heat. Keep cigarettes away from the rain canopy.
•Make sure the rain canopy does not get caught in any moving mechanism on the chassis or stroller.
•Always remove the rain canopy before folding up the chassis or stroller.
•Clean the rain canopy with a sponge and soapy water. Do not use harsh detergents.
SAFETY BELT
56• Make sure that the strap has been correctly inserted as shown in Figure A. Fasten the safety belt as shown in Figure B.
57• To unfasten the safety belt, press the sides of the buckle (Figure A) and pull the waist belt outwards (Figure B).
58• The new safety belt is easier to wear, thanks to the “snap open and shut” system. Before attaching the safety belt, attach the small buckle to the backrest by inserting the tab into the special holder, as shown in the figure. Next, fasten the safety belt on your child, and then detach the belt from the backrest to allow the child more freedom of movement. The small buckle should be placed below the childʼs shoulders.
ADJUSTING THE BACKREST
59• The backrest reclines in four different positions. To recline the backrest, lift the handle (Figure A) while lowering the backrest (Figure B), stopping at the desired position. To raise the backrest, pull it upwards.
REMOVABLE LINING
60• To remove the lining from the stroller, unhook the sack fasteners from the armrests, as shown by the arrows.
61• Unbutton the sack from the seat, and slip it off the hooks on the footboard.
62• Unbutton the side buttons on the sack, as shown in the figure. Slip the safety belt leg divider out from under the seat.
63• Unbutton the buttons on the sack from the seat, and slip the sack off the hooks on the footboard. Slip the sack off the bottom of the stroller.
PLIKO P3 NAKED STROLLER with the
GANCIOMATIC SYSTEM
The Ganciomatic system is a practical, fast way to fasten the Navetta bassinet unit and the Primo Viaggio car seat – which are both equipped with the Ganciomatic system - to the Pliko P3 Naked stroller, using the Ganciomatic hooks.
GANCIOMATIC HOOKS ON THE STROLLER 64• To raise the Ganciomatic hooks on the stroller, lift
the sack in the corners of the seat and turn the two hooks upwards until they click into place.
65• To lower the Ganciomatic hooks on the stroller, pull the lever outwards while turning the hooks downwards, as shown in the figure.
PLIKO P3 NAKED + NAVETTA
66• To fasten the Navetta bassinet unit to the stroller, it is necessary to first:
-Set the brakes on the stroller;
-Completely lower the backrest on the stroller;
-Raise the Ganciomatic hooks on the stroller;
-Remove the front bar and insert the caps to close the stroller armrests;
-Lift the stroller footboard to its highest position;
-Hold the Navetta bassinet unit by its handle;
-Place the bassinet unit on the Ganciomatic hooks on the stroller, keeping the head of the bassinet unit on the opposite side from the stroller handlebars;
-Press down with both hands on the sides of the Navetta bassinet unit, until it clicks into place;
-To remove the Navetta bassinet unit from the stroller, consult the instruction manual.
PLIKO P3 NAKED + PRIMO VIAGGIO 67• To fasten the Primo Viaggio car seat to the
stroller, it is necessary to first: - Set the brakes on the stroller;
