Program Your Personal Transmitter Setting
All GTO transmitters are set to a standard code at the factory and are ready to operate your GTO gate operator. For your safety and security, we strongly recommend that you replace the factory setting with your own personal setting. Follow the directions below:
NOTE: If you have multiple transmitters, you should adjust all of them at this time. 
[RB741/RB742/RB743].
Step 1
Use a small phillips head screw driver to remove the transmitter cover.
Step 2
Set the transmitter DIP switches using a small screwdriver. There are nine (9) switches; each can be placed in three different positions (+, 0,
WARNING: No other adjustments should be made inside the transmitter.
Step 3
Program the new setting into the control board:
LED
+ | 1 | 2 |
|
|
0 |
|
|
| |
– |
| 3 | 4 |
|
|
|
|
| |
|
|
| 5 | 6 |
A23S |
|
| ||
|
| 7 | ||
|
|
|
| 8 |
ALKALINE |
|
| Y | 9 |
|
| E | ||
|
| 12V | EC | |
|
|
| ||
| BATT |
|
| |
|
| ER |
| |
+1 2 3 4 5 6 7 8 9 |
0 |
ECE |
A.Press and hold transmitter button.
B.Press and hold the LEARN RMT (Learn Remote) button on the control board until the alarm sounds.
C.Release transmitter button. The new code is stored in control board memory.
D.Release the LEARN RMT (Learn Remote) button.
NOTE: If you have purchased additional transmitters, program the settings for all at this time.
Step 4
AT THIS POINT YOU SHOULD TEST RECEIVER RANGE BEFORE PERMANENTLY INSTALLING IT.
The Troubleshooting Wizard has detailed information this and other Installations.
24/7 Troubleshooting Wizard: http://
support.gtoinc.com
CLOSE TIME | STALL FORCE | |
120 | MIN | MAX |
TART OFF | 1 2 |
|
|
|
| ON | ||||||||||
|
|
|
| |||||||||||||
G |
|
|
| OFF |
|
|
| ON ON | ||||||||
|
|
|
|
|
| |||||||||||
|
|
|
|
| PULL | 3 4 |
|
|
|
| PUSH | |||||
PEN |
|
| DLY. |
|
|
| DIP SIMULT. | |||||||||
|
|
|
|
| ||||||||||||
|
|
|
|
|
|
| OFF |
|
|
|
|
|
| ON | ||
|
|
|
|
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
| OFF |
|
|
|
|
|
| ON | ||
|
|
|
|
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
STATUS |
|
LEARN RMT |
|
S3 |
|
LEARN | Learn Remote |
MAST LIMIT | Button |
S2 |
|
LEARN |
|
2ND LIMIT |
|
S4 |
|
GTO 4000XLS Instruction Manual © 01.10.12 17