GTO 12, R4854 01, 10 installation manual Generation 3 Visual Feedback, Voltage Readings

Page 35

Generation 3 Visual Feedback

SYMPTOM	DIAGNOSIS	CHECK:
Status (clear)1 blink	Cycle Terminal	• Disconnect the push button, keypad, intercom keypad, or
	Shorted	any other accessory wired to this terminal.
		• Try the remote. If the remote works, then the problem is
		the accessory.
Status (clear) 2	Safety Terminal	• Disconnect the loop detector, photo beam, or any other
blinks	Shorted	accessory wired to this terminal.
		• Try the remote. If the remote works, the problem is the
		accessory.
Status (clear) 3	Exit Terminal	• Disconnect exit wand, loop detector, photo beam, or any
blinks	Shorted	other accessory wired to this terminal.
		• Try remote. If the remote works, the problem is the
		accessory.
Status (clear) 4	Shadow Terminal	• Disconnect the loop detector, photo beam, or any other
blinks	Shorted	accessory wired to this terminal.
		• Try remote. If the remote works, the problem is the
		accessory.
Status (clear) 5	Close Edge	• Disconnect the edge sensor, photo beam, or any other
blinks	Terminal Shorted	accessory wired to this terminal.
		• Try the remote. If the remote works, the problem is the
		accessory.
Status (clear) 6	Open Edge	• Disconnect edge sensor, photo beam, or any other
blinks	Terminal Shorted	accessory wired to this terminal.
		• Try the remote. If the remote works, the problem is the
		accessory.
RF (yellow) Flickers	Receiving 318 MHz	• Normal operation when remote or wireless keypad is used.
	RF
RF (yellow)OFF	No 318 MHz RF	• Battery in Remote
	Received	• Program Remote
		• Antenna Receiver Connections
		• Antenna Receiver

Power (green)	AC or Solar Power	• Normal Operation
ON	Present
ON

VOLTAGE READINGS

18 Vac Transformer	18.0 to 22.0 Vac
10 W Solar panel (single)	18.0 to 22.0 Vdc
In FULL SUN — measure voltage with the Solar Panel Disconnected.
12 V, 7 amp hour Battery	12.5 to 13.5 Vdc
or Two 12V, 7 amp hour Batteries if using solar power
Measure voltage at battery terminals with battery disconnected
Charging circuit	12.0 to 14.8 Vdc

Measure voltage at battery terminals with battery connected

GTO 4000XLS Instruction Manual © 01.10.12 25

Image 35

Contents 4000XLS For Your Records When You Know Multiply By To FindClass Rating Table of Contents Please Read This First 24/7 Troubleshooting Wizard http//support.gtoinc.comBefore YOU Begin to Install Your Automatic Gate Operator How To Manually Open and Close the Gate Important Safety InstructionsFor The Consumer Important Safety InstructionsAny control device Within gray area Never InstallInstall Warning Signs Entrapment Protection Required Safety Precautions for GatesSecondary Means of Protection Against Entrapment Entrapment Alarm UL 325 30A.1.1ADC Swing Series Control Technical SpecificationsPower DriveZone Watts Determine Charging Option for Battery Transformer or SolarSolar Panel and Gate Activity Chart Before You BeginPrepare the Gate Check Direction of Gate SwingBracket BOX HB4000 4000XLS Parts ListTools Needed Materials You may Need for the InstallationPull-To-Open Gates Gate Opens into the Property Install the OperatorInstallation Overview Install the Post Bracket AssemblyStep Hair pin clip Check ClearanceAttach Operator Install Gate BracketInstall Closed Position Stop Plate Receiver cable Mount the Control Box and ReceiverMount the receiver Never Splice Wires Connect Operator Power CableConnect the Power Input Make sure the exposed wires do not touch each other Connect BatteryBe certain not to let the exposed wires touch each other To Close Control Board SettingsSet Closed Position Limit for Pull-To-Open Applications Set Auto Close Time Adjust the Stall Force Setting24/7 Troubleshooting Wizard http Support.gtoinc.com Program Your Personal Transmitter SettingDIP Switches DIP Switch SettingsInput Connections Connecting AccessoriesWiring Accessories Swinging gates shall not open into public access areas Push-To-Open Installation InformationInstall the Operator Set Control Board for Push-To-Open Setting the Open Position Limit Push-To-Open InstallationsColumn Installation Generation 3 Audible Feedback Troubleshooting GuideSymptom Diagnosis Check Voltage Readings Generation 3 Visual Feedback800am-700pm Monday-Friday EST Repair ServiceAccessories for 4000XLS Gooseneck Pedestal F100/F110 Residential Wireless Entry Intercom F3100MBCWireless Vehicle Sensor R4500 Wireless Driveway Alarm R4450Push Button Control RB101 Replacement Transformer RB570Photo Beams R4222 Pin Lock FM345Access Systems