GTO 10, R4854 01, 12 Troubleshooting Guide, Generation 3 Audible Feedback, Symptom Diagnosis Check

Page 34

Troubleshooting Guide

If your gate operator does not function properly after it is installed, use this guide before calling the GTO Service Department.

Generation 3 Audible Feedback

SYMPTOM	DIAGNOSIS	CHECK:

1 short beep upon	Circuit Board	• Normal Operation
power up	Powered Up &
	Ready

1 short beep upon	Blown Fuse	• Fuse
activation	Low or Bad Battery	• Battery Under Load
	Low or Bad Battery	• Battery Harness Connections
	Loose Battery	• Battery Harness Connections
	Loose Battery
	Connection
Continuous	Circuit Board	• Path of Gate
Uninterrupted	Senses an	• Gate for Level and Plumb
Alarm	Obstruction	• Stall Force Adjustment
		• Disconnect Safety Devices
		• Rev Counter

1 beep with 10	Low Battery	• Fuses
seconds off	Condition	• Battery Harness Connections
		• Battery Under Load

1 beep then 2	Master Motor	• Connections to Master Inputs
beeps	Terminals Shorted	• Master Arm Power Cable
		• Motor
		• Circuit Board

1 beep with 2	Master Arm Limit	• Connections to Master Inputs
seconds off	Switch Error	• Master Arm Power Cable

3 beeps with 2	Master Arm Rev	• Connections to Master Inputs
seconds off	Counter Error	• Master Arm Power Cable
		• Rev Counter

24GTO 4000XLS Instruction Manual © 01.10.12

Image 34

Contents 4000XLS Class Rating When You Know Multiply By To FindFor Your Records Table of Contents Before YOU Begin to Install Your Automatic Gate Operator 24/7 Troubleshooting Wizard http//support.gtoinc.comPlease Read This First Important Safety Instructions How To Manually Open and Close the GateImportant Safety Instructions For The ConsumerNever Install Any control device Within gray areaRequired Safety Precautions for Gates Install Warning Signs Entrapment ProtectionEntrapment Alarm UL 325 30A.1.1A Secondary Means of Protection Against EntrapmentDC Swing Series Drive Technical SpecificationsPower ControlBefore You Begin Determine Charging Option for Battery Transformer or SolarSolar Panel and Gate Activity Chart Zone WattsCheck Direction of Gate Swing Prepare the Gate4000XLS Parts List Bracket BOX HB4000Materials You may Need for the Installation Tools NeededInstall the Post Bracket Assembly Install the OperatorInstallation Overview Pull-To-Open Gates Gate Opens into the PropertyStep Check Clearance Hair pin clipInstall Gate Bracket Attach OperatorInstall Closed Position Stop Plate Mount the receiver Mount the Control Box and ReceiverReceiver cable Connect Operator Power Cable Never Splice WiresConnect the Power Input Be certain not to let the exposed wires touch each other Connect BatteryMake sure the exposed wires do not touch each other Set Closed Position Limit for Pull-To-Open Applications Control Board SettingsTo Close Adjust the Stall Force Setting Set Auto Close TimeProgram Your Personal Transmitter Setting 24/7 Troubleshooting Wizard http Support.gtoinc.comDIP Switch Settings DIP SwitchesConnecting Accessories Input ConnectionsWiring Accessories Install the Operator Push-To-Open Installation InformationSwinging gates shall not open into public access areas Setting the Open Position Limit Push-To-Open Installations Set Control Board for Push-To-OpenColumn Installation Symptom Diagnosis Check Troubleshooting GuideGeneration 3 Audible Feedback Generation 3 Visual Feedback Voltage ReadingsRepair Service 800am-700pm Monday-Friday ESTAccessories for 4000XLS Wireless Driveway Alarm R4450 Residential Wireless Entry Intercom F3100MBCWireless Vehicle Sensor R4500 Gooseneck Pedestal F100/F110Pin Lock FM345 Replacement Transformer RB570Photo Beams R4222 Push Button Control RB101Access Systems