Graco EQ300C manual Dust and Debris Hazard

Page 3

Warnings

Warnings

The following warnings are for the setup, use, grounding, maintenance, and repair of this equipment. The exclamation point symbol alerts you to a general warning and the hazard symbols refer to procedure-specific risks. When these symbols appear in the body of this manual or on warning labels, refer back to these Warnings. Product-specific hazard symbols and warnings not covered in this section may appear throughout the body of this manual where applicable.

WARNING

DUST AND DEBRIS HAZARD

Use of this equipment can result in the release of potentially harmful dust or toxic substances from the abrasive being used, the coatings being removed, and the base object being blasted.

• For use only by sophisticated users familiar with applicable governmental safety and industrial hygiene regulators.

• Use equipment only in a well-ventilated area.

•Wear a properly fit-tested and government approved respirator suitable for the dust conditions.

•Follow local ordinances and/or regulations for disposal of toxic substances and debris.

EQUIPMENT MISUSE HAZARD

Misuse can cause death or serious injury.

•Do not operate the unit when fatigued or under the influence of drugs or alcohol.

•Do not exceed the maximum working pressure or temperature rating of the lowest rated

system component. See Technical Data in all equipment manuals.

• Do not use this equipment without hose restraints and coupler pins installed on all air and blast hose couplings.

•Do not blast unstable objects. The high amount of fluid flow from the nozzle can potentially move heavy objects.

•Do not exceed load rating of lift eyes.

•Do not operate equipment on or stand on an unstable support. Keep effective footing and balance at all times.

•Use fluids and solvents that are compatible with equipment wetted parts. See Technical Data in all equipment manuals. Read fluid and solvent manufacturer’s warnings. For complete information about your material, request MSDS from distributor or retailer.

•Do not leave the work area while equipment is energized or under pressure.

•Turn off all equipment and follow the Pressure Relief Procedure when equipment is not in use.

•Check equipment daily. Repair or replace worn or damaged parts immediately with genuine manufacturer’s replacement parts only.

•Do not alter or modify equipment. Alterations or modifications may void agency approvals and create safety hazards.

•Make sure all equipment is rated and approved for the environment in which you are using it.

•Use equipment only for its intended purpose. Call your distributor for information.

•Route hoses and cables away from traffic areas, sharp edges, moving parts, and hot surfaces.

•Do not kink or over bend hoses or use hoses to pull equipment.

•Keep children and animals away from work area.

•Comply with all applicable safety regulations.

334667B

3

Page 2 Page 4
Image 3
Page 2 Page 4
Contents EcoQuip Vapor Abrasive Blast System Important Safety InstructionsRelated Manuals ModelsDust and Debris Hazard Burn Hazard OEM System Guidelines MetricCompressor Size and Hose Length Minimum ID Metric EQ300C and EQ600C System Component IdentificationDataTrak Controls KeyDataTrak see DataTrak Controls, Pressure Relief Procedure Operation Checklist Before StartingConnecting the Blast Hose and Air Hose Setting Up the Equipment 10 gal 200-500 lb Ti24824a 0 0 0 8 8 0 0 0 3 Blasting on Higher Surfaces Blasting TipsSteel Metering Valve SettingsGrit Size Blast Pressure Abrasive Dose Blast Angle General WoodUsing the Wash Feature Refilling the Pot with Abrasive Shutting Down Operation Winterizing the Equipment See Repairing the Main Air Regulator TroubleshootingProblem Cause Solution See Cleaning the Auto-Vent Valve,Intact. See Hose Schematic, See Setting Up the Equipment,See Repairing the Diaphragm Valve Procedure see Shutting Down,Setting Up the Equipment, Properly. See Hose Schematic,Metering Valve Settings, See Pressure Relief Procedure,If flushing does not solve the problem, see Checking for Leaks Troubleshooting ExamplesPneumatic Blast Control Circuit Repairing the Main Air Regulator Perform Pressure Relief Procedure,Repair Flushing the Diaphragm Valve Perform the Pressure Relief Procedure, Repairing the Diaphragm ValveCleaning the Auto-Vent Valve Replacing the DataTrak Battery Replace BatteryApproved Batteries Replacing the DataTrak Fuse Replace FuseApproved Fuses DataTrak Part Series Letter Fuse Required EQ300C and EQ600C PartsPressure POT EQ300C and EQ600C Parts ListEnclosure Part Description Qty Enclosure Parts ListPressure Pot Parts List Pressure PotRef. Part Description Qty Hose Schematic Model Series Brakes Vapor Abrasive Blast Systems and AccessoriesEcoQuip Skid Systems EcoQuip Trailer SystemsModel Description Mobile/Skid UnitsTrailer Units ModelHoses NozzlesModel Description Type Length Blast Control Common Spare Parts Other AccessoriesDimensions Technical Specifications EQ300SEQ600S Graco Information Graco Extended Warranty for EcoQuip Components
Top Page Image Contents