Sanyo VCC-WB2000 instruction manual Alarm Setting

Page 37

Alarm Setting

4 Set the following alarm recording settings as required.

When an alarm signal is input, the alarm data is stored in the camera’s memory.

•ALARM BUFFERING “ON”

•BUFFERING AREA

•PRIORITY

•ALARM RESOLUTION

•OVERWRITE

5 Once you have finished changing the settings, click the [SET] button.

If an outside intruder activates the infrared sensor, the ALARM indicator illuminates red on the live image screen. If a buzzer or lamp is connected to the ALARM OUT terminal, the buzzer will sound or the lamp will illuminate.

1EXTERNAL ALARM setting

This sets the polarity for the infrared sensor or similar that is connected to the ALARM IN terminal at the rear of the camera.

Available settings:

•OFF: No external alarm input is detected.

•NC: Normal close (normally closed, but input is detected when open).

•NO: Normal open (normally open, but input is detected when closed).

2MOTION DETECTOR setting

Set to “ON” when making motion detector settings. The MOTION DETECTOR SET screen will be displayed and you can then make settings such as sensitivity level.

3ALARM MODE setting

This sets if external alarm and/or motion sensor input triggers an alarm.

Available settings:

•AND: An alarm is generated when both the external alarm and the motion sensor receive alarm input.

•OR: An alarm is generated when either the external alarm or the motion sensor receives alarm input.

4ALARM OUT setting

This sets the polarity for the buzzer or lamp that is connected to the ALARM OUT terminal at the rear of the camera.

Available settings:

•OFF: No external alarm is output.

•NC: Normal close (normally closed, but an alarm is output when open).

•NO: Normal open (normally open, but an alarm is output when closed).

5ALARM TIME setting

This sets the duration of alarm output.

Available settings: 2 seconds to 5 minutes

Note: This setting is not the same as the

duration of alarm recording.

6ALARM BUFFERING setting

Set this to “ON” when alarm images are to be recorded.

7BUFFERING AREA setting

This sets the ratio between the amount of space for the memory areas used for recording pre-alarm and post-alarm images.

– 36 –

English

Image 37

Contents Network Camera VCC-WB2000Contents Information to user Safety GuardPrecautions Accessories FeaturesOperating environment Power indicator Monitor OUT connectorName and Function of Each Part Lens mount capName and Function of Each Part Attach the CS mount-type lens Attaching the LensFor C mount type Turn on the camera’s power Flange Back AdjustmentBasic Connections ConnectionsRemoving the wireless LAN card Inserting the wireless LAN cardConnections PPP Dial-up Connections Network Camera Settings Installation of Plug-in Software Network Camera SettingsUninstalling the plug-in software Click the Install buttonClick the Finish button Cookie Settings Browser SettingsCamera uses cookies Computer and Camera Settings Closing the initial window Network Connection SettingsSanyo Network CAMERA, the Unit is Click the Network button in the main menuSet the password Network SET SettingsAccess level UsernameHttp Port Number Network SpeedCurrent Channel Wireless LAN SET SettingsEncryption KEY WEP EnciphermentType in the commands to use for controlling the modem PPP SET SettingsCircuit Type AuthenticationBaud Rate Data SizeAUTO/FINE radio buttons Menu Screen and Main MenuCAMERA, the Unit is Disconnected Menu Screen and Main MenuOpening and Closing the Initial Screen Viewing Camera ImagesViewing Camera Images When you have finished, click the network disconnect buttonSelect the language and then click the SET button Clock Unset indicator Live View SettingsClick the Live View button in the main menu Lit green NetcamResolution Expansion Live View SettingsSaving Images into a Computer Click the View Frame button in the main menu View Frame OperationsBack button Live Image Camera SettingsCamera Title IrisBright Camera SettingsElectronic Shutter White BalanceType in the new camera title e.g. CAM1 Setting the camera titleClick the SET button External Alarm Sensor Settings Alarm SettingClick the Alarm button in the main menu Change the External Alarm setting to NC or noAlarm Setting Picture Quality Motion Detector SET SettingsTime Expansion memory cards Alarm Data Recording CapacityInserting the memory card Removing the memory cardPlaying Back Alarm Data Recording Alarm DataClick the Alarm Data indicator while it is red or green Buffer Data View screen Playing Back Expansion Memory Card Images Deleting Alarm ImagesClick the Delete button Pre-alarm and Post-alarm Recording Daylight Saving Mode Clock SET SettingsClock SET TimezoneStatus Checking RS-232C Settings RS-232C SETFirmware Version SUB-MICROCOMPUTER VersionIs the link indicator flashing? TroubleshootingIf the camera cannot be connected If you forget the IP AddressSpecifications Dimensions Specifications136 mm 85 mm 126 mm 57 mm 12 mm 51 mm Exclusions Page Page Printed on recycled paper 1AC6P1P2545 L5AB2/US 0702KP-CZ