Bosch Appliances 5000 IP installation manual Coax grounding

Page 12

12 en Safety	DINION capture 5000 IP

The Exposure Hazard Value for the product (ratio of the Exposure level to the Exposure limit) is up to 1.8 at a test distance of 200 mm or 8 inches. The Hazard Distance (distance beyond which the product falls into the exempt/safe group) is at most 350 mm or 14 inches. Note that typical operating distances for license plate capture (3.8 m or 12.5 feet and greater) are much greater than the Hazard Distance.

When servicing the unit, physically disconnect the power supply to avoid possible IR exposure to the eyes. If physical disconnection is not possible, use appropriate shielding to block the LED panel or use eye protection with a transmission of 50% or less at a wavelength of 850 nm.

Coax grounding:

–Ground the cable system if connecting an outside cable system to the unit.

–Follow proper safety precautions such as grounding for

any outdoor device connected to this unit.

U.S.A. models only - Section 810 of the National Electrical Code, ANSI/NFPA No.70, provides information regarding proper grounding of the mount and supporting structure, grounding of the coax to a discharge unit, size of grounding conductors, location of discharge unit, connection to grounding electrodes, and requirements for the grounding electrode.

Disposal - Your Bosch product was developed and manufactured with high-quality material and components that can be recycled and reused. This symbol means that electronic and electrical appliances, which have reached the end of their working life, must be collected and disposed of separately from household waste material. Separate collecting systems are usually in place for disused electronic and electrical products. Please dispose of these units at an environmentally compatible recycling facility, per European Directive 2002/96/

EC

Electronic Surveillance - This device is intended for use in public areas only. U.S. federal law strictly prohibits surreptitious recording of oral communications.

1.0 2012.01

Installation Manual

Bosch Security Systems, Inc.

Image 12

Contents Dinion capture 5000 IP Page Table of Contents Basic Mode Advanced ModeOperation via the browser ALC Dimensional Drawings 116 Safety Safety precautionsImportant safety instructions Dinion capture 5000 IP Safety en En Safety Dinion capture 5000 IP Important notices Risk GroupCoax grounding Dinion capture 5000 IP Safety en En Safety Dinion capture 5000 IP FCC & Ices compliance FCC & Ices InformationInformations FCC et Ices En Safety Dinion capture 5000 IP Bosch notices Video lossCopyright TrademarksParts List DescriptionQuantity Description Installing the Dinion capture Determining the RangeRanges based on capturing Field of View at Optimal Capture DistanceDetermining the Angle Model Capture OptimalRange Distance Mounting the Dinion capture En Installing the Dinion capture Dinion capture 5000 IP Dinion capture 5000 IP Installing the Dinion capture en Preparing the Wiring Power Input Connections Ethernet and Power ConnectionsVideo Connection for Installation Making the Connections Connecting to a Coax Cable Using a microSD Card To insert a microSD cardResetting the Dinion capture 5000 IP Automatic Mode Switching Mode Details To setup Automatic Mode SwitchingTo disable Automatic Mode Switching 1 Alarm input, page 103, for more informationConfiguration Install MenuMenu Navigation Keys FullSun Mode Pre-Defined ModesMode Lens Wizard submenu Selection DescriptionDefault submenu Network submenuBrowser connection System requirementsPassword protection in camera Establishing the connectionProtected network Connecting to a hardware decoder Alarm connectionConnection established LivepageSettings Operation via the browser LivepageProcessor load Image selection Display StampingDigital I/O System Log / Event LogSaving snapshots Recording video sequencesRunning recording program Audio communication Recordings Controlling playbackSelecting Recordings Export to FTPSlide control BookmarksBasic Mode Basic Mode menu treeSaving changes Device Access PasswordPassword Camera nameConfirm password Date/TimeDevice date, time and zone Time server IP addressClick Set and Reboot NetworkIP address Subnet maskEncoder RecordingSystem Overview Storage mediumAdvanced Mode Advanced Mode menu treeDinion capture 5000 IP Advanced Mode en General IdentificationCamera ID Camera namePassword Date/Time Date formatDevice date / Device time Device time zoneDisplay Stamping Camera name stampingAlarm mode stamping Alarm messageTime stamping Display millisecondsWeb Interface AppearanceLivepage Functions Logging Camera ModePre-defined modes Mode ID Copy mode toRestore Mode Defaults 2 ALC ALC levelPeak average SpeedDefault shutter / Fixed shutter Shutter/AGCShutter Actual shutterEnhance GainMaximum gain / Fixed gain Actual gainAuto black Sharpness levelDynamic noise reduction Peak white invertInstallation Manual Profile Configuration Profile nameTarget bit rate Maximum bit rateVideo resolution Expert Settings4CIF/D1 GOP structureDefault Select H.264 Settings Encoder Streams264 BP+ bit-rate-limited MP SD 264 BP+ bit-rate MP SD LimitedPrivacy Masks AudioJpeg stream En Advanced Mode Dinion capture 5000 IP Installer Menu Recording Storage Management Formatting Storage Media Deactivating Storage Media Stream profile settings Recording ProfilesRecording includes Standard recordingAlarm recording Retention TimeRecording Scheduler WeekdaysHolidays Recording Status Profile namesActivate recording Recording statusAlarm Alarm ConnectionsSelect 10 in the Number of destination IP address list box Video transmissionStream Remote portDecoder SSL encryptionAuto-connect AudioVideo Content Analyses VCA VCA configuration- Profiles Aggregation time sAnalysis type Motion detectorSensitivity Minimum object size Debounce time 1 sSelecting the area Trigger delay s Tamper detectionGlobal change slider Global changeScene too bright Scene too darkScene too noisy Reference checkAppearing edges VCA configuration Scheduled Deleting HolidaysDinion capture 5000 IP Advanced Mode en VCA configuration Event triggered Delay sTrigger Trigger activeAudio Alarm Audio alarmSignal Ranges NameAlarm E-Mail Destination address Sender nameTest e-mail Alarm Task Editor Alarm input InterfacesRelay Trigger relay Network Access Automatic IP assignmentDNS server address Details Video transmissionHttp browser port Https browser portInterface mode ETH Enable DynDNSRCP+ port Telnet supportHost name User nameForce registration now StatusAuthentication AdvancedSnmp host address / 2. Snmp host address Snmp trapsMulticast Rtsp portUPnP TCP MetadataEnable Multicast AddressPort StreamingFTP Posting Service MaintenanceEncryption FirmwareConfiguration Maintenance log LicensesSystem Overview SSL certificateDimensional Drawings Dinion capturePage Bosch Security Systems, Inc