Bosch Appliances 5000 IP installation manual Network submenu, Default submenu

Page 36

36 en Configuration	DINION capture 5000 IP

4.2.3Network submenu

To operate the DINION capture 5000 IP in your network, a network-valid IP address must be assigned. The factory default IP address is 192.168.0.1.

Item	Selection	Description

IP Address		Enter an IP address for the camera.
		Use LEFT/RIGHT to change position in
		the address, use UP/DOWN to select
		the digit. Use SELECT to exit the
		address edit screen.

Subnet Mask		Enter the Subnet mask (default
		255.255.255.0).

Gateway		Enter a Gateway address.

DHCP		If the network has a DHCP server for
		dynamic IP address allocation, set this
		parameter to On to activate the
		automatic acceptance of DHCP-
		assigned IP addresses.

EXIT		Returns to Install menu.

The new IP address, subnet mask, and gateway address are set when leaving the menu. The camera reboots internally and the new values are set after a few seconds.

4.2.4Default submenu

Item	Selection	Description

Restore All?	No, Yes	Restores all settings of the six modes
		to their default (factory) values. Select
		YES then press the Menu/Select
		button to restore all values.
		When completed the message
		RESTORED! is shown.

1.0 2012.01

Installation Manual

Bosch Security Systems, Inc.

Image 36

Contents Dinion capture 5000 IP Page Table of Contents Basic Mode Advanced ModeOperation via the browser ALC Dimensional Drawings 116 Safety Safety precautionsImportant safety instructions Dinion capture 5000 IP Safety en En Safety Dinion capture 5000 IP Important notices Risk GroupCoax grounding Dinion capture 5000 IP Safety en En Safety Dinion capture 5000 IP FCC & Ices compliance FCC & Ices InformationInformations FCC et Ices En Safety Dinion capture 5000 IP Bosch notices Video lossCopyright TrademarksParts List DescriptionQuantity Description Installing the Dinion capture Determining the RangeRanges based on capturing Field of View at Optimal Capture DistanceDetermining the Angle Model Capture OptimalRange Distance Mounting the Dinion capture En Installing the Dinion capture Dinion capture 5000 IP Dinion capture 5000 IP Installing the Dinion capture en Preparing the Wiring Power Input Connections Ethernet and Power ConnectionsVideo Connection for Installation Making the Connections Connecting to a Coax Cable Using a microSD Card To insert a microSD cardResetting the Dinion capture 5000 IP Automatic Mode Switching Mode Details To setup Automatic Mode SwitchingTo disable Automatic Mode Switching 1 Alarm input, page 103, for more informationConfiguration Install MenuMenu Navigation Keys FullSun Mode Pre-Defined ModesMode Lens Wizard submenu Selection DescriptionDefault submenu Network submenuBrowser connection System requirementsPassword protection in camera Establishing the connectionProtected network Connecting to a hardware decoder Alarm connectionConnection established LivepageSettings Operation via the browser LivepageProcessor load Image selection Display StampingDigital I/O System Log / Event LogSaving snapshots Recording video sequencesRunning recording program Audio communication Recordings Controlling playbackSelecting Recordings Export to FTPSlide control BookmarksBasic Mode Basic Mode menu treeSaving changes Device Access PasswordPassword Camera nameConfirm password Date/TimeDevice date, time and zone Time server IP addressClick Set and Reboot NetworkIP address Subnet maskEncoder RecordingSystem Overview Storage mediumAdvanced Mode Advanced Mode menu treeDinion capture 5000 IP Advanced Mode en General IdentificationCamera ID Camera namePassword Date/Time Date formatDevice date / Device time Device time zoneDisplay Stamping Camera name stampingAlarm mode stamping Alarm messageTime stamping Display millisecondsWeb Interface AppearanceLivepage Functions Logging Camera ModePre-defined modes Mode ID Copy mode toRestore Mode Defaults 2 ALC ALC levelPeak average SpeedDefault shutter / Fixed shutter Shutter/AGCShutter Actual shutterEnhance GainMaximum gain / Fixed gain Actual gainAuto black Sharpness levelDynamic noise reduction Peak white invertInstallation Manual Profile Configuration Profile nameTarget bit rate Maximum bit rateVideo resolution Expert Settings4CIF/D1 GOP structureDefault Select H.264 Settings Encoder Streams264 BP+ bit-rate-limited MP SD 264 BP+ bit-rate MP SD LimitedPrivacy Masks AudioJpeg stream En Advanced Mode Dinion capture 5000 IP Installer Menu Recording Storage Management Formatting Storage Media Deactivating Storage Media Stream profile settings Recording ProfilesRecording includes Standard recordingAlarm recording Retention TimeRecording Scheduler WeekdaysHolidays Recording Status Profile namesActivate recording Recording statusAlarm Alarm ConnectionsSelect 10 in the Number of destination IP address list box Video transmissionStream Remote portDecoder SSL encryptionAuto-connect AudioVideo Content Analyses VCA VCA configuration- Profiles Aggregation time sAnalysis type Motion detectorSensitivity Minimum object size Debounce time 1 sSelecting the area Trigger delay s Tamper detectionGlobal change slider Global changeScene too bright Scene too darkScene too noisy Reference checkAppearing edges VCA configuration Scheduled Deleting HolidaysDinion capture 5000 IP Advanced Mode en VCA configuration Event triggered Delay sTrigger Trigger activeAudio Alarm Audio alarmSignal Ranges NameAlarm E-Mail Destination address Sender nameTest e-mail Alarm Task Editor Alarm input InterfacesRelay Trigger relay Network Access Automatic IP assignmentDNS server address Details Video transmissionHttp browser port Https browser portInterface mode ETH Enable DynDNSRCP+ port Telnet supportHost name User nameForce registration now StatusAuthentication AdvancedSnmp host address / 2. Snmp host address Snmp trapsMulticast Rtsp portUPnP TCP MetadataEnable Multicast AddressPort StreamingFTP Posting Service MaintenanceEncryption FirmwareConfiguration Maintenance log LicensesSystem Overview SSL certificateDimensional Drawings Dinion capturePage Bosch Security Systems, Inc