Alpine PXA-H800 Initial System Start-Up, Using with Ai-NET Connections, Turning Power On and Off

Page 12

From a PC

Basic Operation

Initial System Start-Up

If the system stops working properly, turn the ignition switch to off, and then on again. If the system still does not work properly, reset the unit.

1 Press RESET switch with a ballpoint pen or similar pointed object.

<Right side>

RESET switch

The system will be reset and restarted.

Reset when power is off.

Resetting does not erase the settings stored in the system.

Using with Ai-NET Connections

When the unit is connected to the head unit through Ai-NET, some operations can be controlled with the head unit.

The following operations are controlled with the head unit. The Commander and PC will no longer control these when the head unit is connected.

Turning Power On and Off (page 10)

Switching the Sources (page 12)

Adjusting Subwoofer/Balance/Fader/Volume (page 11, 12)

You can set Defeat (page 12) and Calling of the stored settings (Preset Call) (page 13) with the head unit, Commander, or PC.

Please refer to the Owner’s Manual of the head unit.

Turning Power On and Off

You cannot turn power on/off from the PC. Turn power on/off on the Commander. Refer to Commander Section “Turning Power On and Off” (page 35).

When an Ai-NET compatible head unit is connected, the power of the unit is linked with the power of the head unit.

When the power for PXA-H800 is turned off, Sound Manager for PXA-H800 will be closed.

If an Ai-NET compatible head unit is not connected, the PXA-H800 is automatically turned on when Sound Manager for PXA-H800 is started.

Operating the Sound Manager for PXA- H800 Menu

On the Main menu, you can upgrade the software and save/load the setup value, etc.

Saving the Setup Data (File)

You can save the current setup values in your PC as a file.

Up to 6 setup data sets can be stored in the preset of the device. Use this feature if you want to store more, or for backing up.

1 Click [File(F)].

2 Click [Save Current Data(S)].

The “Save As” box will be shown.

3 Select the location where you want to save the file and enter a name for the file to save.

The file extension of the setup data file is “.pre”.

Loading the Setup Data (File)

You can load the data saved in “Saving the Setup Data (File)” (previous section).

1 Click [File(F)].

2 Click [Load Current Data(L)].

“Open File” box will be shown.

3 Select the setting data and click [Open].

The selected file will be loaded.

If the speaker/AUX input system stored in the data does not match the current system, the data cannot be loaded.

10-EN

Image 12
Contents PXA-H800 Page From a PC From the Commander Information Operating Instructions How to Read this Manual From a PC From the Commander Function listLocation of Controls PXA-H800Sound Manager for PXA-H800 RUX-C800 Commander sold separately Features About the Audio SettingBefore You First Use the Unit About OperatingInstalling Sound Manager for PXA-H800 About the Offline modeBefore installing, all active programs must be stopped Start Sound Manager for PXA-H800Using with Ai-NET Connections Turning Power On and OffInitial System Start-Up Operating the Sound Manager for PXA- H800 MenuAudio Adjustment Loading the ImprintEQ Measurement Data FileDownloading the Software Option Viewing the Version Information OptionSetting Defeat Switching the SourcesStoring the Preset Values Preset Store Recalling a Stored Setting Preset Call Setting the Speaker System Output System Select13-EN Setting the Speakers Speaker Setup/ Setting the Subwoofers Setting the AUX Input System AUX Input System Select14-EN Setting the AUX Input AUX Setting the Digital Input Digital AUXSetting the AUX Volume Input level AUX in Gain Adjusting the AUX Volume level AUX LevelBefore Performing Automatic Measurement Naming the AUX Input AUX Name16-EN Setting ImprintEQ 17-EN18-EN Adjusting and Saving the Target Curve Turning ImprintEQ On/OffSaving ImprintEQ Measurement Data on a 19-ENAdjusting the Time Correction Automatically Auto TCR Adjusting for Road Noise RoadEQ20-EN Click Auto TCR for Shortcut tab in the main menuWhen you click ON, select the level Turning RoadEQ On/Off21-EN Click on or OFF for RoadEQSetting MX Plus Ai-NET Mode Setting MX Plus Standalone Mode22-EN Setting the Graphic EQ 23-ENClick a frequency and drag up or down to adjust the level To adjust another channel, repeat Steps 4 through24-EN Displaying the data Click Show All DataSetting the Parametric EQ 25-ENClick P.EQ for Shortcut tab in the main menu Click P.EQ in the main menuAdjusting X-Over and Switching the Phases About the Crossover X-Over26-EN Crossover X-OverClick the indicator of Show 27-ENArrow indicating the dragging direction appears Adjusting the Time Correction TCR Calculation of time correctionEntering the time correction 28-ENSetting contents 0.00 to 20.00 ms in 0.05 ms steps Setting contents Inch29-EN Click either cm or inchSetting Euphony Euphony Click Multi Channel Manager of the Function switching tabSet and adjust 2ch Playback Mode, EUPHONY, Dolby Pro Logic 30-ENUsing Dolby Pro Logic II Dolby Pro Logic 31-ENMulti Channel Function Adjustment Procedure Multi Channel Setup32-EN Adjusting the Speaker Volume Level Output Level Adjusting the Acoustic Image BIMixing the Low Range Audio for the Rear Rear Mix 33-ENSetting the Linear PCM PCM Mode Achieving Powerful High Volume Sound Listening ModeAdjusting the DVD Level DVD Level 34-ENAdjusting Subwoofer Subwoofer Navigation Audio Volume Adjustment35-EN Adjusting the MX Plus Level MX Plus SETUP/LEVEL Adjustment Adjusting Balance Between Left and Right BalanceAdjusting Fader Between Front and Rear Fader Setting Defeat DefeatSetting the Speaker System System Select 37-ENSetting the Speakers Speaker Setup Setting the Subwoofer Output SW Channel38-EN OFF/ONSetting the AUX Input System AUX Input Setup Setting the AUX Input AUX39-EN Setting the Digital Input Digital AUX Setting the AUX Volume Input Level AUX in GainAdjusting the AUX Volume Level AUX Level 40-ENMixing Navi Audio Guidance Navi Mix Setup Rotate the Rotary encoder to make adjustmentWhen the setting is complete, press Naming the AUX Input AUX NameTurning ImprintEQ On/Off 42-ENBe sure to read before performing the automatic measurement Press and hold FUNC. for at least 2 secondsWhen Finished appears, press Rotary encoder 43-ENPress the Rotary encoder Setting the MX Plus Ai-NET Mode 44-ENSetting the MX Plus Standalone Mode To adjust another source, press and repeat Steps 8 through45-EN Press twice to go back to the screen for StepSetting the Equalizer Mode EQ Mode 46-ENG-EQ screen is displayed Select the channel you want to adjust by pressing Channel 47-EN48-EN Band FRONT/REAR/CENTER 1 toHz to 20kHz in 1/6 octave steps Hz to 200 Hz in 1/6 octave steps49-EN Front LOW Rear Center SUBWOOFER*1 Front HighFront L MID Front R MID 50-EN TCR screen is displayedSetting the Time Correction Adjustment Unit TCR Parameter To adjust another channel, repeat Steps 9 through51-EN Setting the 2-Channel Signal Playback Mode Mode Setting Euphony Euphony52-EN Using Dolby Pro Logic II Dolby Plii 53-ENDolby Plii screen is displayed Adjusting the Speaker Volume Level Output Level 54-ENSelect the channel by pressing Channel Adjusting the Acoustic Image BI Mixing the Low Range Audio for the Rear Rear Mix55-EN Setting the Linear PCM PCM Mode Achieving Powerful High Volume Sound Listening ModeAdjust the frequency by rotating the Rotary encoder 56-ENAdjusting the DVD Level DVD Level Lowering Volume Quickly MuteTurning the Back Light Off Black OUT function 57-ENAdjusting the Brightness Level of the Display Dimmer Level Adjusting the Brightness of the Display Dimmer58-EN Switching the Display Display mode switches for every push59-EN Press ViewSystem Configuration 60-ENOutput System Input SystemTerminology 61-ENIndication Commander RUX-C800 Case of Difficulty62-EN Specifications 63-ENDimensions 64-ENComponents