Alpine PXA-H800 owner manual Audio Adjustment, Loading the ImprintEQ Measurement Data File, 11-EN

Page 13

Loading the ImprintEQ Measurement Data (File)

Load the ImprintEQ measurement data stored in the PC into PXA- H800.

1 Click [File(F)].

2 Click [Send ImprintEQ Data to PXA-H800(I)].

“Open File” box will be shown.

The file extension of the ImprintEQ measurement data file is “.ieq”.

3 Select the ImprintEQ measurement data stored in the PC and click [Open].

The selected file will be loaded. The Memory Selection screen will be displayed.

4 Select [ImprintEQ Memory 1] or [ImprintEQ Memory 2], and click [OK].

The file is written in the PXA-H800 memory.

Select [File] to save ImprintEQ measurement data on a PC.

For the ImprintEQ, refer to “Setting ImprintEQ” (page 17).

Downloading the Software (Option)

You can download the software to a newer version.

Warning for downloading

When you download a file, all setup data in the PXA-H800 will be deleted. Please note that once deleted it cannot be recovered. Before downloading, it is recommended to save the setting data. Refer to “Saving the Setup Data (File)” (page 10).

Downloading takes approximately 20 minutes. Do not turn off the PXA-H800 or disconnect the USB cable until the download is completed.

1 From the Alpine Web site, download the file for upgrading the software and store it in your PC.

For details on the procedure, refer to the Alpine Web site.

2 Click [Option(O)].

3 Click [Software Download(D)].

From a PC

4 Click [OK] when a confirmation message appears.

“Open File” box will be shown.

5 Select the file you have stored in Step 1 and click [Open].

The file will be downloaded and the version upgrade process will be started. When the download is completed, a confirmation message will be displayed.

6 Click [OK].

Following the instructions on the screen, restart the PXA- H800 unit and Sound Manager for PXA-H800.

Viewing the Version Information (Option)

You can view the version information for PXA-H800 and Sound Manager for PXA-H800.

1 Click [Option(O)].

2 Click [Version Information (V)].

The version information will be shown.

Audio Adjustment

When an Ai-NET compatible head unit is connected, the audio settings are adjusted at the head unit and you cannot adjust the unit from the PC.

1 Make adjustments using [ ], [ ], [ ], [ ], [ ], and [ ] for “Fader,” “Balance,” “SubW Lv,” or “Master Volume” in the main menu.

11-EN

Image 13
Contents PXA-H800 Page From a PC From the Commander Information Operating Instructions From a PC From the Commander Function list How to Read this ManualPXA-H800 Location of ControlsSound Manager for PXA-H800 RUX-C800 Commander sold separately About the Audio Setting FeaturesBefore You First Use the Unit About OperatingAbout the Offline mode Installing Sound Manager for PXA-H800Before installing, all active programs must be stopped Start Sound Manager for PXA-H800Turning Power On and Off Using with Ai-NET ConnectionsInitial System Start-Up Operating the Sound Manager for PXA- H800 MenuLoading the ImprintEQ Measurement Data File Audio AdjustmentDownloading the Software Option Viewing the Version Information OptionSwitching the Sources Setting DefeatStoring the Preset Values Preset Store Setting the Speaker System Output System Select Recalling a Stored Setting Preset Call13-EN Setting the AUX Input System AUX Input System Select Setting the Speakers Speaker Setup/ Setting the Subwoofers14-EN Setting the Digital Input Digital AUX Setting the AUX Input AUXSetting the AUX Volume Input level AUX in Gain Adjusting the AUX Volume level AUX LevelNaming the AUX Input AUX Name Before Performing Automatic Measurement16-EN 17-EN Setting ImprintEQ18-EN Turning ImprintEQ On/Off Adjusting and Saving the Target CurveSaving ImprintEQ Measurement Data on a 19-ENAdjusting for Road Noise RoadEQ Adjusting the Time Correction Automatically Auto TCR20-EN Click Auto TCR for Shortcut tab in the main menuTurning RoadEQ On/Off When you click ON, select the level21-EN Click on or OFF for RoadEQSetting MX Plus Standalone Mode Setting MX Plus Ai-NET Mode22-EN 23-EN Setting the Graphic EQTo adjust another channel, repeat Steps 4 through Click a frequency and drag up or down to adjust the level24-EN Displaying the data Click Show All Data25-EN Setting the Parametric EQClick P.EQ for Shortcut tab in the main menu Click P.EQ in the main menuAbout the Crossover X-Over Adjusting X-Over and Switching the Phases26-EN Crossover X-Over27-EN Click the indicator of ShowArrow indicating the dragging direction appears Calculation of time correction Adjusting the Time Correction TCREntering the time correction 28-ENSetting contents Inch Setting contents 0.00 to 20.00 ms in 0.05 ms steps29-EN Click either cm or inchClick Multi Channel Manager of the Function switching tab Setting Euphony EuphonySet and adjust 2ch Playback Mode, EUPHONY, Dolby Pro Logic 30-EN31-EN Using Dolby Pro Logic II Dolby Pro LogicMulti Channel Setup Multi Channel Function Adjustment Procedure32-EN Adjusting the Acoustic Image BI Adjusting the Speaker Volume Level Output LevelMixing the Low Range Audio for the Rear Rear Mix 33-ENAchieving Powerful High Volume Sound Listening Mode Setting the Linear PCM PCM ModeAdjusting the DVD Level DVD Level 34-ENNavigation Audio Volume Adjustment Adjusting Subwoofer Subwoofer35-EN Adjusting Balance Between Left and Right Balance Adjusting the MX Plus Level MX Plus SETUP/LEVEL AdjustmentAdjusting Fader Between Front and Rear Fader Setting Defeat Defeat37-EN Setting the Speaker System System SelectSetting the Subwoofer Output SW Channel Setting the Speakers Speaker Setup38-EN OFF/ONSetting the AUX Input AUX Setting the AUX Input System AUX Input Setup39-EN Setting the AUX Volume Input Level AUX in Gain Setting the Digital Input Digital AUXAdjusting the AUX Volume Level AUX Level 40-ENRotate the Rotary encoder to make adjustment Mixing Navi Audio Guidance Navi Mix SetupWhen the setting is complete, press Naming the AUX Input AUX Name42-EN Turning ImprintEQ On/OffBe sure to read before performing the automatic measurement Press and hold FUNC. for at least 2 seconds43-EN When Finished appears, press Rotary encoderPress the Rotary encoder 44-EN Setting the MX Plus Ai-NET ModeTo adjust another source, press and repeat Steps 8 through Setting the MX Plus Standalone Mode45-EN Press twice to go back to the screen for Step46-EN Setting the Equalizer Mode EQ ModeG-EQ screen is displayed 47-EN Select the channel you want to adjust by pressing ChannelBand FRONT/REAR/CENTER 1 to 48-ENHz to 20kHz in 1/6 octave steps Hz to 200 Hz in 1/6 octave stepsFront LOW Rear Center SUBWOOFER*1 Front High 49-ENFront L MID Front R MID TCR screen is displayed 50-ENTo adjust another channel, repeat Steps 9 through Setting the Time Correction Adjustment Unit TCR Parameter51-EN Setting Euphony Euphony Setting the 2-Channel Signal Playback Mode Mode52-EN 53-EN Using Dolby Pro Logic II Dolby PliiDolby Plii screen is displayed 54-EN Adjusting the Speaker Volume Level Output LevelSelect the channel by pressing Channel Mixing the Low Range Audio for the Rear Rear Mix Adjusting the Acoustic Image BI55-EN Achieving Powerful High Volume Sound Listening Mode Setting the Linear PCM PCM ModeAdjust the frequency by rotating the Rotary encoder 56-ENLowering Volume Quickly Mute Adjusting the DVD Level DVD LevelTurning the Back Light Off Black OUT function 57-ENAdjusting the Brightness of the Display Dimmer Adjusting the Brightness Level of the Display Dimmer Level58-EN Display mode switches for every push Switching the Display59-EN Press View60-EN System ConfigurationOutput System Input System61-EN TerminologyCase of Difficulty Indication Commander RUX-C80062-EN 63-EN Specifications64-EN DimensionsComponents