Alpine PXA-H800 owner manual Case of Difficulty, Indication Commander RUX-C800, 62-EN

Page 64

In Case of Difficulty

If you encounter a problem, please turn the power off, then on again. If the unit is still not functioning normally, please review the items in the following checklist. This guide will help you isolate the problem if the unit is at fault. Otherwise, make sure the rest of your system is properly connected or consult your authorized Alpine dealer.

No function or display.

•Vehicle’s ignition is off.

-Turn the ignition key on. If connected as per the instructions, the unit will not operate with the vehicle’s ignition off.

•Unit’s power is not on.

-Turn the ignition key on. Press one of the switches on the Commander to turn power on. If an Ai-NET compatible head unit is connected, turn on the power by the head unit.

•Power cord connection is faulty.

-Connect the power cord correctly.

•Display does not show anything (BLACK OUT function).

-Cancel BLACK OUT function (see page 57).

•Blown fuse.

-Check the fuse of the unit; replace with the proper value if necessary.

•Internal micro-computer malfunctioned due to interference noise etc.

-Press the RESET switch with a ball-point pen or other pointed article.

Power is on but no sound is coming out.

•Volume level is at Minimum.

-Raise the volume level (see pages 12, 36).

•External input system does not match the setup.

-Set the system so that it matches the connected input (see

pages 14, 39).

The sound is not output from the speakers.

•Cord connection is faulty.

-Connect the cord correctly.

•Speaker is in "OFF mode."

-Put the speakers in "ON mode" (see pages 14, 38).

•Subwoofers are "OFF."

-Turn the subwoofers "ON" (see pages 14, 38).

Sound adjustment disabled.

•Defeat is "ON."

- Turn Defeat Off (see pages 12, 36).

DVD volume low.

•Volume levels can be different between CD and DVD. - Adjust the DVD Level (see pages 34, 57).

Sources cannot be selected.

•Ai-NET device is connected.

-When an Ai-NET compatible head unit is connected, the source should be switched at the head unit.

Dolby Pro Logic II volume level low.

•Dolby Pro Logic II volume level is generally lower. - Raise the volume level (see pages 12, 36).

Dolby D/Dolby PLII/DTS indicators flash at 1 second intervals simultaneously.

•Software upgrade to a newer version failed. - Consult your Alpine dealer.

POWER indicator flashes at 1 second intervals.

•A failure has occurred.

-Following the instruction on the screen, conduct the corrective measures. Or, consult your Alpine dealer.

RoadEQ does not work.

•Microphone not connected.

-Check to see that the microphone is correctly connected. Also, make sure that the cord is not extremely bent.

•RoadEQ setup not completed.

-Check to see that RoadEQ is correctly completed.

An error during Automatic ImprintEQ adjustment has occured.

•External noise is interfering with measurement.

-Conduct the measurement in a quiet location.

•The speaker bandwidth may be too narrow.

-Check the X-Over setting of each speaker.

•Gain setting of the amplifier may be too low.

-Check the Gain setting.

Software upgrade to a newer version failed.

•During software upgrade, the USB cable was unplugged, the ignition key is turned to OFF position, the unit was affected by another program, etc.

-Stop all active programs, and then upgrade the software again (see page 11).

-If you still have trouble, stop use of the unit and consult your Alpine dealer.

Indication (Commander RUX-C800)

Calibration Error

•Automatic measurement failed for whatever reason.

-Press "Rotary Encoder" to go back to the previous screen and perform the measurement again.

No Mic

•Microphone not connected.

-Check to see that the microphone is correctly connected. Also, make sure that the cord is not extremely bent.

No Mic/RoadEQ Off

•Even when RoadEQ is turned on, if no microphone is connected, RoadEQ is turned off.

-Check to see that the microphone is correctly connected. Also, make sure that the cord is not extremely bent.

No Data

•Settings are called but there is no preset data stored in the system.

- Store the preset values.

System Mismatch

•The called preset values do not match the current speaker system.

- Store the preset values again, using the current speaker system.

62-EN

Page 63 Page 65
Image 64
Page 63 Page 65
Contents PXA-H800 Page From a PC From the Commander Information Operating Instructions How to Read this Manual From a PC From the Commander Function listPXA-H800 Location of ControlsSound Manager for PXA-H800 RUX-C800 Commander sold separately Features About the Audio SettingBefore You First Use the Unit About OperatingInstalling Sound Manager for PXA-H800 About the Offline modeBefore installing, all active programs must be stopped Start Sound Manager for PXA-H800Using with Ai-NET Connections Turning Power On and OffInitial System Start-Up Operating the Sound Manager for PXA- H800 MenuAudio Adjustment Loading the ImprintEQ Measurement Data FileDownloading the Software Option Viewing the Version Information OptionSwitching the Sources Setting DefeatStoring the Preset Values Preset Store Setting the Speaker System Output System Select Recalling a Stored Setting Preset Call13-EN Setting the AUX Input System AUX Input System Select Setting the Speakers Speaker Setup/ Setting the Subwoofers14-EN Setting the AUX Input AUX Setting the Digital Input Digital AUXSetting the AUX Volume Input level AUX in Gain Adjusting the AUX Volume level AUX LevelNaming the AUX Input AUX Name Before Performing Automatic Measurement16-EN Setting ImprintEQ 17-EN18-EN Adjusting and Saving the Target Curve Turning ImprintEQ On/OffSaving ImprintEQ Measurement Data on a 19-ENAdjusting the Time Correction Automatically Auto TCR Adjusting for Road Noise RoadEQ20-EN Click Auto TCR for Shortcut tab in the main menuWhen you click ON, select the level Turning RoadEQ On/Off21-EN Click on or OFF for RoadEQSetting MX Plus Standalone Mode Setting MX Plus Ai-NET Mode22-EN Setting the Graphic EQ 23-ENClick a frequency and drag up or down to adjust the level To adjust another channel, repeat Steps 4 through24-EN Displaying the data Click Show All DataSetting the Parametric EQ 25-ENClick P.EQ for Shortcut tab in the main menu Click P.EQ in the main menuAdjusting X-Over and Switching the Phases About the Crossover X-Over26-EN Crossover X-Over27-EN Click the indicator of ShowArrow indicating the dragging direction appears Adjusting the Time Correction TCR Calculation of time correctionEntering the time correction 28-ENSetting contents 0.00 to 20.00 ms in 0.05 ms steps Setting contents Inch29-EN Click either cm or inchSetting Euphony Euphony Click Multi Channel Manager of the Function switching tabSet and adjust 2ch Playback Mode, EUPHONY, Dolby Pro Logic 30-ENUsing Dolby Pro Logic II Dolby Pro Logic 31-ENMulti Channel Setup Multi Channel Function Adjustment Procedure32-EN Adjusting the Speaker Volume Level Output Level Adjusting the Acoustic Image BIMixing the Low Range Audio for the Rear Rear Mix 33-ENSetting the Linear PCM PCM Mode Achieving Powerful High Volume Sound Listening ModeAdjusting the DVD Level DVD Level 34-ENNavigation Audio Volume Adjustment Adjusting Subwoofer Subwoofer35-EN Adjusting the MX Plus Level MX Plus SETUP/LEVEL Adjustment Adjusting Balance Between Left and Right BalanceAdjusting Fader Between Front and Rear Fader Setting Defeat DefeatSetting the Speaker System System Select 37-ENSetting the Speakers Speaker Setup Setting the Subwoofer Output SW Channel38-EN OFF/ONSetting the AUX Input AUX Setting the AUX Input System AUX Input Setup39-EN Setting the Digital Input Digital AUX Setting the AUX Volume Input Level AUX in GainAdjusting the AUX Volume Level AUX Level 40-ENMixing Navi Audio Guidance Navi Mix Setup Rotate the Rotary encoder to make adjustmentWhen the setting is complete, press Naming the AUX Input AUX NameTurning ImprintEQ On/Off 42-ENBe sure to read before performing the automatic measurement Press and hold FUNC. for at least 2 seconds43-EN When Finished appears, press Rotary encoderPress the Rotary encoder Setting the MX Plus Ai-NET Mode 44-ENSetting the MX Plus Standalone Mode To adjust another source, press and repeat Steps 8 through45-EN Press twice to go back to the screen for Step46-EN Setting the Equalizer Mode EQ ModeG-EQ screen is displayed Select the channel you want to adjust by pressing Channel 47-EN48-EN Band FRONT/REAR/CENTER 1 toHz to 20kHz in 1/6 octave steps Hz to 200 Hz in 1/6 octave stepsFront LOW Rear Center SUBWOOFER*1 Front High 49-ENFront L MID Front R MID 50-EN TCR screen is displayedTo adjust another channel, repeat Steps 9 through Setting the Time Correction Adjustment Unit TCR Parameter51-EN Setting Euphony Euphony Setting the 2-Channel Signal Playback Mode Mode52-EN 53-EN Using Dolby Pro Logic II Dolby PliiDolby Plii screen is displayed 54-EN Adjusting the Speaker Volume Level Output LevelSelect the channel by pressing Channel Mixing the Low Range Audio for the Rear Rear Mix Adjusting the Acoustic Image BI55-EN Setting the Linear PCM PCM Mode Achieving Powerful High Volume Sound Listening ModeAdjust the frequency by rotating the Rotary encoder 56-ENAdjusting the DVD Level DVD Level Lowering Volume Quickly MuteTurning the Back Light Off Black OUT function 57-ENAdjusting the Brightness of the Display Dimmer Adjusting the Brightness Level of the Display Dimmer Level58-EN Switching the Display Display mode switches for every push59-EN Press ViewSystem Configuration 60-ENOutput System Input SystemTerminology 61-ENCase of Difficulty Indication Commander RUX-C80062-EN Specifications 63-EN64-EN DimensionsComponents
Top Page Image Contents