Alpine PXA-H800 Before Performing Automatic Measurement, Naming the AUX Input AUX Name, 16-EN

Page 18

From a PC

Naming the AUX Input (AUX Name)

When you connect an external input source, you can name it with a suitable name (Initial setting: “Auxiliary”).

1 Click [ ] for each AUX and select and click the external input product name from the pull-down menu.

Setting item:

AUX Name

Setting contents: Auxiliary/TV/EXT.DVD/Portable/Game

•This item becomes possible to set only when AUX IN setting is on.

Setting/Adjusting the Navigation Guidance Volume (Navi Mix)

If a navigation system is connected, its voice guidance will be mixed with the system and output from the front speakers (Initial setting: “OFF”). You can adjust the navigation guidance volume (Initial setting: “0 dB”).

1 Click [ON] or [OFF] for “Navi Mix” in the main menu.

If you click [ON], select the setting value.

2 Click [ ] or [ ] to adjust the volume.

Setting contents: -10 to +10 dB

•For details on the connection of a navigation system, refer to the installation manual.

Automatic

Measurement

Function

Before Performing Automatic

Measurement

This unit is equipped with ImprintEQ, RoadEQ, and AutoTCR automatic measurement functions.

WARNING

•Do not perform automatic measurement while the vehicle is running.

Automatic measurement requires microphones to be installed in the cabin to measure acoustic characteristics, and the speakers may output loud noise for measurement. This may interfere with safe driving and lead to an accident.

Be sure to read before performing automatic measurement.

•The automatic measurement should be performed in a quiet place with the engine, air-conditioner, and heater turned off. If a mobile phone or car phone is installed in the vehicle, move them outside of the cabin, or turn the power off. Sound other than the measuring sound (ambient noise around the vehicle, engine noise, and ringtones) may interfere with measurement, resulting in inaccurate measurement of the acoustic characteristics of the cabin.

•Be aware that the battery may be drained if you use the unit for an extended period of time without running the engine.

•The microphone supplied with this product is specifically designed for this type of measurement. Use of any other microphone will give poor or no results. Use of microphones other than the one supplied is not recommended.

•If the system is equipped with a power amplifier with input level control or a powered subwoofer, the measurement may not be possible if the input level is set low. However, to perform correct measurement, the input level should not be set too high.

•For a power amplifier with low-pass filter, turn off the low-pass filter of the power amplifier to make measurement. The low-pass filter in the powered subwoofer or the power amplifier for a subwoofer should be set at the highest cutoff frequency.

Measurement sequence for the automatic measurement functions

Perform the automatic measurement in the following sequence.

When ImprintEQ is used:

First, ImprintEQ, then RoadEQ.

When ImprintEQ is not used:

First, Auto TCR, then RoadEQ.

•When ImprintEQ is used, AutoTCR is not required.

•When ImprintEQ and AutoTCR are performed after RoadEQ, re- perform RoadEQ.

16-EN

Page 17 Page 19
Image 18
Page 17 Page 19
Contents PXA-H800 Page From a PC From the Commander Information Operating Instructions How to Read this Manual From a PC From the Commander Function listLocation of Controls PXA-H800Sound Manager for PXA-H800 RUX-C800 Commander sold separately Before You First Use the Unit FeaturesAbout the Audio Setting About OperatingBefore installing, all active programs must be stopped Installing Sound Manager for PXA-H800About the Offline mode Start Sound Manager for PXA-H800Initial System Start-Up Using with Ai-NET ConnectionsTurning Power On and Off Operating the Sound Manager for PXA- H800 MenuDownloading the Software Option Audio AdjustmentLoading the ImprintEQ Measurement Data File Viewing the Version Information OptionSetting Defeat Switching the SourcesStoring the Preset Values Preset Store Recalling a Stored Setting Preset Call Setting the Speaker System Output System Select13-EN Setting the Speakers Speaker Setup/ Setting the Subwoofers Setting the AUX Input System AUX Input System Select14-EN Setting the AUX Volume Input level AUX in Gain Setting the AUX Input AUXSetting the Digital Input Digital AUX Adjusting the AUX Volume level AUX LevelBefore Performing Automatic Measurement Naming the AUX Input AUX Name16-EN Setting ImprintEQ 17-EN18-EN Saving ImprintEQ Measurement Data on a Adjusting and Saving the Target CurveTurning ImprintEQ On/Off 19-EN20-EN Adjusting the Time Correction Automatically Auto TCRAdjusting for Road Noise RoadEQ Click Auto TCR for Shortcut tab in the main menu21-EN When you click ON, select the levelTurning RoadEQ On/Off Click on or OFF for RoadEQSetting MX Plus Ai-NET Mode Setting MX Plus Standalone Mode22-EN Setting the Graphic EQ 23-EN24-EN Click a frequency and drag up or down to adjust the levelTo adjust another channel, repeat Steps 4 through Displaying the data Click Show All DataClick P.EQ for Shortcut tab in the main menu Setting the Parametric EQ25-EN Click P.EQ in the main menu26-EN Adjusting X-Over and Switching the PhasesAbout the Crossover X-Over Crossover X-OverClick the indicator of Show 27-ENArrow indicating the dragging direction appears Entering the time correction Adjusting the Time Correction TCRCalculation of time correction 28-EN29-EN Setting contents 0.00 to 20.00 ms in 0.05 ms stepsSetting contents Inch Click either cm or inchSet and adjust 2ch Playback Mode, EUPHONY, Dolby Pro Logic Setting Euphony EuphonyClick Multi Channel Manager of the Function switching tab 30-ENUsing Dolby Pro Logic II Dolby Pro Logic 31-ENMulti Channel Function Adjustment Procedure Multi Channel Setup32-EN Mixing the Low Range Audio for the Rear Rear Mix Adjusting the Speaker Volume Level Output LevelAdjusting the Acoustic Image BI 33-ENAdjusting the DVD Level DVD Level Setting the Linear PCM PCM ModeAchieving Powerful High Volume Sound Listening Mode 34-ENAdjusting Subwoofer Subwoofer Navigation Audio Volume Adjustment35-EN Adjusting Fader Between Front and Rear Fader Adjusting the MX Plus Level MX Plus SETUP/LEVEL AdjustmentAdjusting Balance Between Left and Right Balance Setting Defeat DefeatSetting the Speaker System System Select 37-EN38-EN Setting the Speakers Speaker SetupSetting the Subwoofer Output SW Channel OFF/ONSetting the AUX Input System AUX Input Setup Setting the AUX Input AUX39-EN Adjusting the AUX Volume Level AUX Level Setting the Digital Input Digital AUXSetting the AUX Volume Input Level AUX in Gain 40-ENWhen the setting is complete, press Mixing Navi Audio Guidance Navi Mix SetupRotate the Rotary encoder to make adjustment Naming the AUX Input AUX NameBe sure to read before performing the automatic measurement Turning ImprintEQ On/Off42-EN Press and hold FUNC. for at least 2 secondsWhen Finished appears, press Rotary encoder 43-ENPress the Rotary encoder Setting the MX Plus Ai-NET Mode 44-EN45-EN Setting the MX Plus Standalone ModeTo adjust another source, press and repeat Steps 8 through Press twice to go back to the screen for StepSetting the Equalizer Mode EQ Mode 46-ENG-EQ screen is displayed Select the channel you want to adjust by pressing Channel 47-ENHz to 20kHz in 1/6 octave steps 48-ENBand FRONT/REAR/CENTER 1 to Hz to 200 Hz in 1/6 octave steps49-EN Front LOW Rear Center SUBWOOFER*1 Front HighFront L MID Front R MID 50-EN TCR screen is displayedSetting the Time Correction Adjustment Unit TCR Parameter To adjust another channel, repeat Steps 9 through51-EN Setting the 2-Channel Signal Playback Mode Mode Setting Euphony Euphony52-EN Using Dolby Pro Logic II Dolby Plii 53-ENDolby Plii screen is displayed Adjusting the Speaker Volume Level Output Level 54-ENSelect the channel by pressing Channel Adjusting the Acoustic Image BI Mixing the Low Range Audio for the Rear Rear Mix55-EN Adjust the frequency by rotating the Rotary encoder Setting the Linear PCM PCM ModeAchieving Powerful High Volume Sound Listening Mode 56-ENTurning the Back Light Off Black OUT function Adjusting the DVD Level DVD LevelLowering Volume Quickly Mute 57-ENAdjusting the Brightness Level of the Display Dimmer Level Adjusting the Brightness of the Display Dimmer58-EN 59-EN Switching the DisplayDisplay mode switches for every push Press ViewOutput System System Configuration60-EN Input SystemTerminology 61-ENIndication Commander RUX-C800 Case of Difficulty62-EN Specifications 63-ENDimensions 64-ENComponents
Top Page Image Contents