Alpine PXA-H800 owner manual Setting ImprintEQ, 17-EN

Page 19

Setting ImprintEQ

ImprintEQ is a system to obtain the optimum acoustic effect from each seat position, based on the automatically measured acoustic data of the cabin.

To use ImprintEQ, you should perform acoustic measurement of the cabin beforehand.

ImprintEQ measurement flow

Prepare the vehicle and install the microphone.

Turn the ignition key to ACC ON position, and start ALPINE

PXA-H800 Sound.

 

 

When it is an automobile

 

 

factory system

For a system

 

 

 

 

other than an

 

Play back the SETUP DISC that comes

automobile

 

with the unit on the head unit.

factory system

 

 

 

 

 

 

Select the listening position.

 

 

 

Following the instructions on the screen, conduct the

automatic measurement.

Select the target curve.

Save the measurement values.

1 Preparing for measurement.

Park the vehicle in a quiet location.

Close doors, windows, sunroof, etc.

Turn the air-conditioner and heater OFF.

Turn off the engine of the vehicle.

2 Preparing the microphone.

Place the microphone at ear level (a camera tripod is useful for this purpose).

The direction of the microphone does not affect the measurement.

3 Turn the ignition switch of the vehicle to ACC (On).

If an air-conditioner or heater is turned on, turn it off. Measurement should not be performed if air-conditioner or heater noise is present.

From a PC

4 Click [ImprintEQ] for [Shortcut] tab in the main menu.

The Automatic Measurement tab screen will be displayed.

When you click [Automatic Measurement] in the Function switching tab, the Automatic Measurement tab screen will also be displayed. Refer to “Operating the Function Switching Tab” (page 7).

5 Click [Setup] for “ImprintEQ.”

The ImprintEQ mode selection screen will be displayed.

6 Select either [Factory Audio] or [Other] and click.

Factory Audio: When an automobile factory system is connected to AUX1, choose this.

Other: Choose [Other] when a head unit other than an automobile factory system (commercially available unit including ALPINE products) is connected.

If you select [Factory Audio], go to Step 7. If you select [Other], go to Step 10.

7 Insert the SETUP DISC into the head unit. Click [START] within 10 seconds of Track01 starting.

8 Following the instructions on the screen, adjust the input level of the device connected to AUX1. When “OK” is displayed, click [OK].

9 Click [START] within 10 seconds of Track02 starting.

Measurement of the frequency characteristic will be started. When measurement is completed, a confirmation message will be displayed.

If you want to stop measurement, click [CANCEL].

10 Click [OK] when a message appears.

The Area Selection screen is displayed.

11 Select the listening position. Select the area from [ALL], [FRONT], [FRONT LEFT], [FRONT RIGHT], and [REAR], and click [Next].

If [ALL] is selected, the system will measures the characteristics from all seat positions.

The measurement screen will be displayed.

17-EN

Image 19
Contents PXA-H800 Page From a PC From the Commander Information Operating Instructions From a PC From the Commander Function list How to Read this ManualPXA-H800 Location of ControlsSound Manager for PXA-H800 RUX-C800 Commander sold separately About Operating FeaturesAbout the Audio Setting Before You First Use the UnitStart Sound Manager for PXA-H800 Installing Sound Manager for PXA-H800About the Offline mode Before installing, all active programs must be stoppedOperating the Sound Manager for PXA- H800 Menu Using with Ai-NET ConnectionsTurning Power On and Off Initial System Start-UpViewing the Version Information Option Audio AdjustmentLoading the ImprintEQ Measurement Data File Downloading the Software OptionSwitching the Sources Setting DefeatStoring the Preset Values Preset Store Setting the Speaker System Output System Select Recalling a Stored Setting Preset Call13-EN Setting the AUX Input System AUX Input System Select Setting the Speakers Speaker Setup/ Setting the Subwoofers14-EN Adjusting the AUX Volume level AUX Level Setting the AUX Input AUXSetting the Digital Input Digital AUX Setting the AUX Volume Input level AUX in GainNaming the AUX Input AUX Name Before Performing Automatic Measurement16-EN 17-EN Setting ImprintEQ18-EN 19-EN Adjusting and Saving the Target CurveTurning ImprintEQ On/Off Saving ImprintEQ Measurement Data on aClick Auto TCR for Shortcut tab in the main menu Adjusting the Time Correction Automatically Auto TCRAdjusting for Road Noise RoadEQ 20-ENClick on or OFF for RoadEQ When you click ON, select the levelTurning RoadEQ On/Off 21-ENSetting MX Plus Standalone Mode Setting MX Plus Ai-NET Mode22-EN 23-EN Setting the Graphic EQDisplaying the data Click Show All Data Click a frequency and drag up or down to adjust the levelTo adjust another channel, repeat Steps 4 through 24-ENClick P.EQ in the main menu Setting the Parametric EQ25-EN Click P.EQ for Shortcut tab in the main menuCrossover X-Over Adjusting X-Over and Switching the PhasesAbout the Crossover X-Over 26-EN27-EN Click the indicator of ShowArrow indicating the dragging direction appears 28-EN Adjusting the Time Correction TCRCalculation of time correction Entering the time correctionClick either cm or inch Setting contents 0.00 to 20.00 ms in 0.05 ms stepsSetting contents Inch 29-EN30-EN Setting Euphony EuphonyClick Multi Channel Manager of the Function switching tab Set and adjust 2ch Playback Mode, EUPHONY, Dolby Pro Logic31-EN Using Dolby Pro Logic II Dolby Pro LogicMulti Channel Setup Multi Channel Function Adjustment Procedure32-EN 33-EN Adjusting the Speaker Volume Level Output LevelAdjusting the Acoustic Image BI Mixing the Low Range Audio for the Rear Rear Mix34-EN Setting the Linear PCM PCM ModeAchieving Powerful High Volume Sound Listening Mode Adjusting the DVD Level DVD LevelNavigation Audio Volume Adjustment Adjusting Subwoofer Subwoofer35-EN Setting Defeat Defeat Adjusting the MX Plus Level MX Plus SETUP/LEVEL AdjustmentAdjusting Balance Between Left and Right Balance Adjusting Fader Between Front and Rear Fader37-EN Setting the Speaker System System SelectOFF/ON Setting the Speakers Speaker SetupSetting the Subwoofer Output SW Channel 38-ENSetting the AUX Input AUX Setting the AUX Input System AUX Input Setup39-EN 40-EN Setting the Digital Input Digital AUXSetting the AUX Volume Input Level AUX in Gain Adjusting the AUX Volume Level AUX LevelNaming the AUX Input AUX Name Mixing Navi Audio Guidance Navi Mix SetupRotate the Rotary encoder to make adjustment When the setting is complete, pressPress and hold FUNC. for at least 2 seconds Turning ImprintEQ On/Off42-EN Be sure to read before performing the automatic measurement43-EN When Finished appears, press Rotary encoderPress the Rotary encoder 44-EN Setting the MX Plus Ai-NET ModePress twice to go back to the screen for Step Setting the MX Plus Standalone ModeTo adjust another source, press and repeat Steps 8 through 45-EN46-EN Setting the Equalizer Mode EQ ModeG-EQ screen is displayed 47-EN Select the channel you want to adjust by pressing ChannelHz to 200 Hz in 1/6 octave steps 48-ENBand FRONT/REAR/CENTER 1 to Hz to 20kHz in 1/6 octave stepsFront LOW Rear Center SUBWOOFER*1 Front High 49-ENFront L MID Front R MID TCR screen is displayed 50-ENTo adjust another channel, repeat Steps 9 through Setting the Time Correction Adjustment Unit TCR Parameter51-EN Setting Euphony Euphony Setting the 2-Channel Signal Playback Mode Mode52-EN 53-EN Using Dolby Pro Logic II Dolby PliiDolby Plii screen is displayed 54-EN Adjusting the Speaker Volume Level Output LevelSelect the channel by pressing Channel Mixing the Low Range Audio for the Rear Rear Mix Adjusting the Acoustic Image BI55-EN 56-EN Setting the Linear PCM PCM ModeAchieving Powerful High Volume Sound Listening Mode Adjust the frequency by rotating the Rotary encoder57-EN Adjusting the DVD Level DVD LevelLowering Volume Quickly Mute Turning the Back Light Off Black OUT functionAdjusting the Brightness of the Display Dimmer Adjusting the Brightness Level of the Display Dimmer Level58-EN Press View Switching the DisplayDisplay mode switches for every push 59-ENInput System System Configuration60-EN Output System61-EN TerminologyCase of Difficulty Indication Commander RUX-C80062-EN 63-EN Specifications64-EN DimensionsComponents