Alpine PXA-H800 Turning ImprintEQ On/Off, Saving ImprintEQ Measurement Data on a, 19-EN

Page 21

20 Select and click the memory where the curve is to be

saved from [ImprintEQ Memory 1] or [ImprintEQ Memory 2]. Click [OK].

From a PC

After the setting, it is recommended to store the setting contents on the unit. For details, refer to “Storing the Preset Values (Preset Store)” (page 12).

Select [File] to save ImprintEQ measurement data on a PC. Refer to “Saving ImprintEQ Measurement Data on a PC” (page 19).

21 Click [Close Window].

To enable this function, Defeat should be is set to ON.

Graphic EQ, Parametric EQ and X-Over Level are set to their initial values during ImprintEQ measurement.

The file extension of the ImprintEQ setting data file is “.ieq”.

When you save the measurement result of ImprintEQ in Memory 1 or 2 for the second time, the memory will be overwritten and the previous data will be lost.

Sound may arrive at the listening position at slightly different times, depending on the speaker and enclosure. To compensate for this, the distance can be adjusted to be larger than the actual distance.

Measurement values will not be lost in the event the system is reset or battery power is disconnected.

Turning ImprintEQ On/Off

1 Click [ImprintEQ] for [Shortcut] tab in the main menu.

The Automatic Measurement tab screen will be displayed.

When you click [Automatic Measurement] in the Function switching tab, the Automatic Measurement tab screen will also be displayed. Refer to “Operating the Function Switching Tab” (page 7).

2 Click [ON] or [OFF] for “ImprintEQ.”

If you click [ON], select the setting value.

3 Click [ ] and select and click either [Memory 1] or [Memory 2].

If you do not use ImprintEQ is not used, select [OFF].

If the speaker system in the “Memory” and the current speaker system do not match, the Memory cannot be retrieved.

When you turn on ImprintEQ, the Graphic EQ, Parametric EQ, Time Correction, and Output Level are automatically adjusted. Each of these values can be further adjusted, but the adjustment ranges for the Graphic EQ and the Parametric EQ are restricted.

When ImprintEQ is on, the Time Correction and X-Over channel will be automatically set at the L/R Separate Adjustment mode.

Saving ImprintEQ Measurement Data on a

PC

1 Click [File] in Step 20 for “Setting ImprintEQ”, and click [OK].

The “Save As” box will be shown.

2 Select the location where you want to save the file and enter a name for the file to save.

For the method to load the data saved on a PC, refer to “Loading the ImprintEQ Measurement Data (File)” (page 11).

Adjusting and Saving the Target Curve

You can adjust the target curve and save it on a PC.

1 Click [Target Curve Setting] in Step 17 for “Setting ImprintEQ.”

The Target Curve Setting screen will be displayed.

When you click [Target Curve] for the [Shortcut] tab in the main menu, the Target Curve Setting screen will be displayed.

2 Drag the curve to adjust it.

Setting contents: -6 to +6dB

3 Click [Save].

The “Save As” box will be shown.

4 Select the location where you want to save the file and enter a name for the file to save.

The file extension of the measurement data file is “.tcv”.

You can retrieve the saved data by clicking [Load].

To restore the target curve to the initial settings, click [Reset]. Click [OK] when confirmation message appears.

Mouse trace function

When you click [Mouse Trace OFF], the mouse trace function becomes enabled, and [Mouse Trace OFF] changes to [Mouse Trace ON]. When dragged, the curve (settings) changes in accordance with the movement of the cursor.

To disable the mouse trace function, click the [Mouse Trace ON].

19-EN

Image 21
Contents PXA-H800 Page From a PC From the Commander Information Operating Instructions From a PC From the Commander Function list How to Read this ManualLocation of Controls PXA-H800Sound Manager for PXA-H800 RUX-C800 Commander sold separately About the Audio Setting FeaturesBefore You First Use the Unit About OperatingAbout the Offline mode Installing Sound Manager for PXA-H800Before installing, all active programs must be stopped Start Sound Manager for PXA-H800Turning Power On and Off Using with Ai-NET ConnectionsInitial System Start-Up Operating the Sound Manager for PXA- H800 MenuLoading the ImprintEQ Measurement Data File Audio AdjustmentDownloading the Software Option Viewing the Version Information OptionSetting Defeat Switching the SourcesStoring the Preset Values Preset Store Recalling a Stored Setting Preset Call Setting the Speaker System Output System Select13-EN Setting the Speakers Speaker Setup/ Setting the Subwoofers Setting the AUX Input System AUX Input System Select14-EN Setting the Digital Input Digital AUX Setting the AUX Input AUXSetting the AUX Volume Input level AUX in Gain Adjusting the AUX Volume level AUX LevelBefore Performing Automatic Measurement Naming the AUX Input AUX Name16-EN 17-EN Setting ImprintEQ18-EN Turning ImprintEQ On/Off Adjusting and Saving the Target CurveSaving ImprintEQ Measurement Data on a 19-ENAdjusting for Road Noise RoadEQ Adjusting the Time Correction Automatically Auto TCR20-EN Click Auto TCR for Shortcut tab in the main menuTurning RoadEQ On/Off When you click ON, select the level21-EN Click on or OFF for RoadEQSetting MX Plus Ai-NET Mode Setting MX Plus Standalone Mode22-EN 23-EN Setting the Graphic EQTo adjust another channel, repeat Steps 4 through Click a frequency and drag up or down to adjust the level24-EN Displaying the data Click Show All Data25-EN Setting the Parametric EQClick P.EQ for Shortcut tab in the main menu Click P.EQ in the main menuAbout the Crossover X-Over Adjusting X-Over and Switching the Phases26-EN Crossover X-OverClick the indicator of Show 27-ENArrow indicating the dragging direction appears Calculation of time correction Adjusting the Time Correction TCREntering the time correction 28-ENSetting contents Inch Setting contents 0.00 to 20.00 ms in 0.05 ms steps29-EN Click either cm or inchClick Multi Channel Manager of the Function switching tab Setting Euphony EuphonySet and adjust 2ch Playback Mode, EUPHONY, Dolby Pro Logic 30-EN31-EN Using Dolby Pro Logic II Dolby Pro LogicMulti Channel Function Adjustment Procedure Multi Channel Setup32-EN Adjusting the Acoustic Image BI Adjusting the Speaker Volume Level Output LevelMixing the Low Range Audio for the Rear Rear Mix 33-ENAchieving Powerful High Volume Sound Listening Mode Setting the Linear PCM PCM ModeAdjusting the DVD Level DVD Level 34-ENAdjusting Subwoofer Subwoofer Navigation Audio Volume Adjustment35-EN Adjusting Balance Between Left and Right Balance Adjusting the MX Plus Level MX Plus SETUP/LEVEL AdjustmentAdjusting Fader Between Front and Rear Fader Setting Defeat Defeat37-EN Setting the Speaker System System SelectSetting the Subwoofer Output SW Channel Setting the Speakers Speaker Setup38-EN OFF/ONSetting the AUX Input System AUX Input Setup Setting the AUX Input AUX39-EN Setting the AUX Volume Input Level AUX in Gain Setting the Digital Input Digital AUXAdjusting the AUX Volume Level AUX Level 40-ENRotate the Rotary encoder to make adjustment Mixing Navi Audio Guidance Navi Mix SetupWhen the setting is complete, press Naming the AUX Input AUX Name42-EN Turning ImprintEQ On/OffBe sure to read before performing the automatic measurement Press and hold FUNC. for at least 2 secondsWhen Finished appears, press Rotary encoder 43-ENPress the Rotary encoder 44-EN Setting the MX Plus Ai-NET ModeTo adjust another source, press and repeat Steps 8 through Setting the MX Plus Standalone Mode45-EN Press twice to go back to the screen for StepSetting the Equalizer Mode EQ Mode 46-ENG-EQ screen is displayed 47-EN Select the channel you want to adjust by pressing ChannelBand FRONT/REAR/CENTER 1 to 48-ENHz to 20kHz in 1/6 octave steps Hz to 200 Hz in 1/6 octave steps49-EN Front LOW Rear Center SUBWOOFER*1 Front HighFront L MID Front R MID TCR screen is displayed 50-ENSetting the Time Correction Adjustment Unit TCR Parameter To adjust another channel, repeat Steps 9 through51-EN Setting the 2-Channel Signal Playback Mode Mode Setting Euphony Euphony52-EN Using Dolby Pro Logic II Dolby Plii 53-ENDolby Plii screen is displayed Adjusting the Speaker Volume Level Output Level 54-ENSelect the channel by pressing Channel Adjusting the Acoustic Image BI Mixing the Low Range Audio for the Rear Rear Mix55-EN Achieving Powerful High Volume Sound Listening Mode Setting the Linear PCM PCM ModeAdjust the frequency by rotating the Rotary encoder 56-ENLowering Volume Quickly Mute Adjusting the DVD Level DVD LevelTurning the Back Light Off Black OUT function 57-ENAdjusting the Brightness Level of the Display Dimmer Level Adjusting the Brightness of the Display Dimmer58-EN Display mode switches for every push Switching the Display59-EN Press View60-EN System ConfigurationOutput System Input System61-EN TerminologyIndication Commander RUX-C800 Case of Difficulty62-EN 63-EN SpecificationsDimensions 64-ENComponents