Alpine PXA-H800 43-EN, Press the Rotary encoder, When Finished appears, press Rotary encoder

Page 45

6 Rotate the [Rotary encoder] to select “Auto TCR,” and then press the [Rotary encoder].

The AUTO TCR screen is displayed.

7 Press the [Rotary encoder].

Countdown will start.

During the 10 second countdown, go outside the vehicle and close the door.

A test signal will be output from the speakers to measure the acoustic characteristics of the cabin. Do not open any doors until the screen indicates “Finished.” If external noise interferes with the measurement, the “Calibration Error” message will appear on the screen. In this case, click [Rotary encoder] again to re-measure.

If you want to stop measurement, press [ ].

If the microphone is not connected, “No Mic” will be displayed and

the measurement will not be carried out. Press [ ] or [Rotary Encoder] to cancel the indication.

8 When “Finished” appears, press [Rotary encoder].

This function is not available when Defeat is set to ON.

Measurement of Auto TCR takes approximately 5 minutes.

Auto TCR measurement result overwrites the manual TCR measurement result.

Sound may arrive at the listening position at slightly different times, depending on the speaker and enclosure. To compensate for this, the distance can be adjusted to be larger than the actual distance.

After the setting, it is recommended to store the setting contents on the unit. For details, refer to “Storing the Preset Values (Preset Store)” (page 36).

Adjusting for Road Noise (RoadEQ)

RoadEQ (REAL-TIME OPTIMIZED ADAPTIVE DRIVING EQ) is a function to automatically adjust the EQ properties in accordance with the road noise while driving.

The Road Equalizer compensates for constantly changing noise, so always keep the microphones connected.

1 Preparing for measurement.

Park the vehicle in a quiet location.

Close doors, windows, sunroof, etc.

Turn the air-conditioner and heater OFF.

Turn off the engine of the vehicle.

2 Preparing the microphone.

Refer to the installation manual.

3 Turn the ignition switch of the vehicle to ACC (On).

If an air-conditioner or heater is turned on, turn it off. Measurement should not be performed if air-conditioner or heater noise is present.

4 Press [FUNC.].

From the Commander

5 Rotate the [Rotary encoder] to select “RoadEQ,” and then press the [Rotary encoder].

6 Rotate the [Rotary encoder] to select “Calibration,” and then press the [Rotary encoder].

The CALIBRATION screen is displayed.

7 Press the [Rotary encoder].

Countdown will start.

During the 10 second countdown, go outside the vehicle and close the door.

A test signal will be output from the speakers to measure the acoustic characteristics of the cabin. Do not open any doors until the screen indicates “Finished.” If external noise interferes with the measurement, the “Calibration Error” message will appear on the screen. In this case, click [Rotary encoder] again to re-measure.

If you want to stop measurement, press [ ].

If the microphone is not connected, “No Mic” will be displayed and

the measurement will not be carried out. Press [ ] or [Rotary Encoder] to cancel the indication.

8 When “Finished” appears, press [Rotary encoder].

This function is not available when Defeat is set to ON.

Measurement of RoadEQ takes approximately 7 minutes.

When you select “Calibration” again, the previous setup data will be erased when count-down is started.

Measurement values will not be lost in the event the system is reset or battery power is disconnected.

Turning RoadEQ On/Off

When automatic measurement is completed, RoadEQ can be turned on or off and its level can be selected.

1 Press [FUNC.].

2 Rotate the [Rotary encoder] to select “Road EQ,” and then press the [Rotary encoder].

3 Rotate the [Rotary encoder] to select “Level Adjustment,” and then press the [Rotary encoder].

The LEVEL ADJUSTMENT screen is displayed.

43-EN

Image 45
Contents PXA-H800 Page From a PC From the Commander Information Operating Instructions From a PC From the Commander Function list How to Read this ManualLocation of Controls PXA-H800Sound Manager for PXA-H800 RUX-C800 Commander sold separately About the Audio Setting FeaturesBefore You First Use the Unit About OperatingAbout the Offline mode Installing Sound Manager for PXA-H800Before installing, all active programs must be stopped Start Sound Manager for PXA-H800Turning Power On and Off Using with Ai-NET ConnectionsInitial System Start-Up Operating the Sound Manager for PXA- H800 MenuLoading the ImprintEQ Measurement Data File Audio AdjustmentDownloading the Software Option Viewing the Version Information OptionSetting Defeat Switching the SourcesStoring the Preset Values Preset Store Recalling a Stored Setting Preset Call Setting the Speaker System Output System Select13-EN Setting the Speakers Speaker Setup/ Setting the Subwoofers Setting the AUX Input System AUX Input System Select14-EN Setting the Digital Input Digital AUX Setting the AUX Input AUXSetting the AUX Volume Input level AUX in Gain Adjusting the AUX Volume level AUX LevelBefore Performing Automatic Measurement Naming the AUX Input AUX Name16-EN 17-EN Setting ImprintEQ18-EN Turning ImprintEQ On/Off Adjusting and Saving the Target CurveSaving ImprintEQ Measurement Data on a 19-ENAdjusting for Road Noise RoadEQ Adjusting the Time Correction Automatically Auto TCR20-EN Click Auto TCR for Shortcut tab in the main menuTurning RoadEQ On/Off When you click ON, select the level21-EN Click on or OFF for RoadEQSetting MX Plus Ai-NET Mode Setting MX Plus Standalone Mode22-EN 23-EN Setting the Graphic EQTo adjust another channel, repeat Steps 4 through Click a frequency and drag up or down to adjust the level24-EN Displaying the data Click Show All Data25-EN Setting the Parametric EQClick P.EQ for Shortcut tab in the main menu Click P.EQ in the main menuAbout the Crossover X-Over Adjusting X-Over and Switching the Phases26-EN Crossover X-OverClick the indicator of Show 27-ENArrow indicating the dragging direction appears Calculation of time correction Adjusting the Time Correction TCREntering the time correction 28-ENSetting contents Inch Setting contents 0.00 to 20.00 ms in 0.05 ms steps29-EN Click either cm or inchClick Multi Channel Manager of the Function switching tab Setting Euphony EuphonySet and adjust 2ch Playback Mode, EUPHONY, Dolby Pro Logic 30-EN31-EN Using Dolby Pro Logic II Dolby Pro LogicMulti Channel Function Adjustment Procedure Multi Channel Setup32-EN Adjusting the Acoustic Image BI Adjusting the Speaker Volume Level Output LevelMixing the Low Range Audio for the Rear Rear Mix 33-ENAchieving Powerful High Volume Sound Listening Mode Setting the Linear PCM PCM ModeAdjusting the DVD Level DVD Level 34-ENAdjusting Subwoofer Subwoofer Navigation Audio Volume Adjustment35-EN Adjusting Balance Between Left and Right Balance Adjusting the MX Plus Level MX Plus SETUP/LEVEL AdjustmentAdjusting Fader Between Front and Rear Fader Setting Defeat Defeat37-EN Setting the Speaker System System SelectSetting the Subwoofer Output SW Channel Setting the Speakers Speaker Setup38-EN OFF/ONSetting the AUX Input System AUX Input Setup Setting the AUX Input AUX39-EN Setting the AUX Volume Input Level AUX in Gain Setting the Digital Input Digital AUXAdjusting the AUX Volume Level AUX Level 40-ENRotate the Rotary encoder to make adjustment Mixing Navi Audio Guidance Navi Mix SetupWhen the setting is complete, press Naming the AUX Input AUX Name42-EN Turning ImprintEQ On/OffBe sure to read before performing the automatic measurement Press and hold FUNC. for at least 2 secondsWhen Finished appears, press Rotary encoder 43-ENPress the Rotary encoder 44-EN Setting the MX Plus Ai-NET ModeTo adjust another source, press and repeat Steps 8 through Setting the MX Plus Standalone Mode45-EN Press twice to go back to the screen for StepSetting the Equalizer Mode EQ Mode 46-ENG-EQ screen is displayed 47-EN Select the channel you want to adjust by pressing ChannelBand FRONT/REAR/CENTER 1 to 48-ENHz to 20kHz in 1/6 octave steps Hz to 200 Hz in 1/6 octave steps49-EN Front LOW Rear Center SUBWOOFER*1 Front HighFront L MID Front R MID TCR screen is displayed 50-ENSetting the Time Correction Adjustment Unit TCR Parameter To adjust another channel, repeat Steps 9 through51-EN Setting the 2-Channel Signal Playback Mode Mode Setting Euphony Euphony52-EN Using Dolby Pro Logic II Dolby Plii 53-ENDolby Plii screen is displayed Adjusting the Speaker Volume Level Output Level 54-ENSelect the channel by pressing Channel Adjusting the Acoustic Image BI Mixing the Low Range Audio for the Rear Rear Mix55-EN Achieving Powerful High Volume Sound Listening Mode Setting the Linear PCM PCM ModeAdjust the frequency by rotating the Rotary encoder 56-ENLowering Volume Quickly Mute Adjusting the DVD Level DVD LevelTurning the Back Light Off Black OUT function 57-ENAdjusting the Brightness Level of the Display Dimmer Level Adjusting the Brightness of the Display Dimmer58-EN Display mode switches for every push Switching the Display59-EN Press View60-EN System ConfigurationOutput System Input System61-EN TerminologyIndication Commander RUX-C800 Case of Difficulty62-EN 63-EN SpecificationsDimensions 64-ENComponents