Alpine PXA-H800 Setting the AUX Input System AUX Input Setup, Setting the AUX Input AUX, 39-EN

Page 41

5 When the setting is complete, press and hold [ ] for at least 2 seconds.

Only when two subwoofers are connected in “Setting the Speaker System (System Select)” (page 37)/“Setting the Speakers (Speaker Setup)” (page 38), is this item able to be set.

If [ ] is pressed during setting, the unit returns to the previous item.

After the setting, it is recommended to store the setting contents on the unit. For details, refer to “Storing the Preset Values (Preset Store)” (page 36).

Setting the AUX Input System (AUX Input Setup)

This step sets the six channel Analog (RCA) input of the unit. The input volume levels can also be set.

At the initial startup, the AUX Input System Select screen is displayed automatically after the speakers are set. Go to Step 3.

1 Press [FUNC.].

2 Rotate the [Rotary encoder] to select “Input Setup,” and then press the [Rotary encoder].

3 Rotate the [Rotary encoder] to select “AUX Input

Setup,” and then press the [Rotary encoder].

The AUX Input setup screen is displayed.

4 Rotate the [Rotary encoder] to select the desired system, and then press the [Rotary encoder].

5.1ch Input:

AUX1 (Front Left, Front Right, Rear Left,

 

Rear Right, Center, Subwoofer)

4ch&2ch Input: AUX1 (Front Left, Front Right, Rear Left,

 

Rear Right)/AUX2 (Left, Right)

2ch×3 Input:

AUX1 (Left, Right)/AUX2 (Left, Right)/AUX3

 

(Left, Right)

Refer to Table 2 (Input Configuration) in “System Configuration” (page 60).

5 Select “OK” by rotating the [Rotary encoder] when a confirmation message appears, and press the [Rotary encoder].

The AUX IN Gain Setup screen is displayed.

When “OK” is selected, the audio output is stopped until the ignition key is turned on/off.

6 Select either “High” or “Low” for each AUX by rotating the [Rotary encoder], and press the [Rotary encoder].

High: When the volume level of the external input is high.

Low: When the volume level of the external input is low.

From the Commander

7 The “Turn ACC Off” screen will be displayed. Turn the ignition key to and then on again.

The settings become effective.

If [ ] is pressed during setting, the unit returns to the previous item.

Gain can also be set in “Setting the AUX Volume Input Level (AUX IN Gain)” (page 40).

When the AUX input system is changed, all the setup values for AUX input will be restored to the initial setup values.

After the setting, it is recommended to store the setting contents on the unit. For details, refer to “Storing the Preset Values (Preset Store)” (page 36).

Setting the AUX Input (AUX IN)

A TV or VCR with RCA audio output can be connected to the unit. Select OFF for the external input not connected (Initial setting: “ON”).

1 Press [FUNC.].

2 Rotate the [Rotary encoder] to select “Input Setup,” and then press the [Rotary encoder].

3 Rotate the [Rotary encoder] to select “AUX IN,” and then press the [Rotary encoder].

The AUX selection screen is displayed.

4 Select the AUX you want to set by rotating the [Rotary encoder], and press the [Rotary encoder].

Settings item:

AUX 2/AUX 3/Ai-NET(HU)/Ai-NET(CHG)

AUX1 cannot be set.

If you connect Ai-NET/RCA Interface cable (KCA-121B) to the terminals of the device Head Unit input terminal (Ai-NET input) / Changer input terminal (Ai-NET input), you can use it as AUX.

The number of AUX varies depending on the AUX Input Setup (page 39).

5 Rotate the [Rotary encoder] to select “ON” or “OFF”, and then press the [Rotary encoder].

6 To set another AUX, press [ ] and repeat Steps 4 and 5.

7 When the setting is complete, press and hold [ ] for at least 2 seconds.

When an Ai-NET compatible head unit is connected, external input of the PXA-H800 becomes unavailable, and this setting will be disabled.

If [ ] is pressed during setting, the unit returns to the previous item.

After the setting, it is recommended to store the setting contents on the unit. For details, refer to “Storing the Preset Values (Preset Store)” (page 36).

39-EN

Image 41
Contents PXA-H800 Page From a PC From the Commander Information Operating Instructions From a PC From the Commander Function list How to Read this ManualSound Manager for PXA-H800 Location of ControlsPXA-H800 RUX-C800 Commander sold separately About the Audio Setting FeaturesBefore You First Use the Unit About OperatingAbout the Offline mode Installing Sound Manager for PXA-H800Before installing, all active programs must be stopped Start Sound Manager for PXA-H800Turning Power On and Off Using with Ai-NET ConnectionsInitial System Start-Up Operating the Sound Manager for PXA- H800 MenuLoading the ImprintEQ Measurement Data File Audio AdjustmentDownloading the Software Option Viewing the Version Information OptionStoring the Preset Values Preset Store Setting DefeatSwitching the Sources 13-EN Recalling a Stored Setting Preset CallSetting the Speaker System Output System Select 14-EN Setting the Speakers Speaker Setup/ Setting the SubwoofersSetting the AUX Input System AUX Input System Select Setting the Digital Input Digital AUX Setting the AUX Input AUXSetting the AUX Volume Input level AUX in Gain Adjusting the AUX Volume level AUX Level16-EN Before Performing Automatic MeasurementNaming the AUX Input AUX Name 17-EN Setting ImprintEQ18-EN Turning ImprintEQ On/Off Adjusting and Saving the Target CurveSaving ImprintEQ Measurement Data on a 19-ENAdjusting for Road Noise RoadEQ Adjusting the Time Correction Automatically Auto TCR20-EN Click Auto TCR for Shortcut tab in the main menuTurning RoadEQ On/Off When you click ON, select the level21-EN Click on or OFF for RoadEQ22-EN Setting MX Plus Ai-NET ModeSetting MX Plus Standalone Mode 23-EN Setting the Graphic EQTo adjust another channel, repeat Steps 4 through Click a frequency and drag up or down to adjust the level24-EN Displaying the data Click Show All Data25-EN Setting the Parametric EQClick P.EQ for Shortcut tab in the main menu Click P.EQ in the main menuAbout the Crossover X-Over Adjusting X-Over and Switching the Phases26-EN Crossover X-OverArrow indicating the dragging direction appears Click the indicator of Show27-EN Calculation of time correction Adjusting the Time Correction TCREntering the time correction 28-ENSetting contents Inch Setting contents 0.00 to 20.00 ms in 0.05 ms steps29-EN Click either cm or inchClick Multi Channel Manager of the Function switching tab Setting Euphony EuphonySet and adjust 2ch Playback Mode, EUPHONY, Dolby Pro Logic 30-EN31-EN Using Dolby Pro Logic II Dolby Pro Logic32-EN Multi Channel Function Adjustment ProcedureMulti Channel Setup Adjusting the Acoustic Image BI Adjusting the Speaker Volume Level Output LevelMixing the Low Range Audio for the Rear Rear Mix 33-ENAchieving Powerful High Volume Sound Listening Mode Setting the Linear PCM PCM ModeAdjusting the DVD Level DVD Level 34-EN35-EN Adjusting Subwoofer SubwooferNavigation Audio Volume Adjustment Adjusting Balance Between Left and Right Balance Adjusting the MX Plus Level MX Plus SETUP/LEVEL AdjustmentAdjusting Fader Between Front and Rear Fader Setting Defeat Defeat37-EN Setting the Speaker System System SelectSetting the Subwoofer Output SW Channel Setting the Speakers Speaker Setup38-EN OFF/ON39-EN Setting the AUX Input System AUX Input SetupSetting the AUX Input AUX Setting the AUX Volume Input Level AUX in Gain Setting the Digital Input Digital AUXAdjusting the AUX Volume Level AUX Level 40-ENRotate the Rotary encoder to make adjustment Mixing Navi Audio Guidance Navi Mix SetupWhen the setting is complete, press Naming the AUX Input AUX Name42-EN Turning ImprintEQ On/OffBe sure to read before performing the automatic measurement Press and hold FUNC. for at least 2 secondsPress the Rotary encoder When Finished appears, press Rotary encoder43-EN 44-EN Setting the MX Plus Ai-NET ModeTo adjust another source, press and repeat Steps 8 through Setting the MX Plus Standalone Mode45-EN Press twice to go back to the screen for StepG-EQ screen is displayed Setting the Equalizer Mode EQ Mode46-EN 47-EN Select the channel you want to adjust by pressing ChannelBand FRONT/REAR/CENTER 1 to 48-ENHz to 20kHz in 1/6 octave steps Hz to 200 Hz in 1/6 octave stepsFront L MID Front R MID 49-ENFront LOW Rear Center SUBWOOFER*1 Front High TCR screen is displayed 50-EN51-EN Setting the Time Correction Adjustment Unit TCR ParameterTo adjust another channel, repeat Steps 9 through 52-EN Setting the 2-Channel Signal Playback Mode ModeSetting Euphony Euphony Dolby Plii screen is displayed Using Dolby Pro Logic II Dolby Plii53-EN Select the channel by pressing Channel Adjusting the Speaker Volume Level Output Level54-EN 55-EN Adjusting the Acoustic Image BIMixing the Low Range Audio for the Rear Rear Mix Achieving Powerful High Volume Sound Listening Mode Setting the Linear PCM PCM ModeAdjust the frequency by rotating the Rotary encoder 56-ENLowering Volume Quickly Mute Adjusting the DVD Level DVD LevelTurning the Back Light Off Black OUT function 57-EN58-EN Adjusting the Brightness Level of the Display Dimmer LevelAdjusting the Brightness of the Display Dimmer Display mode switches for every push Switching the Display59-EN Press View60-EN System ConfigurationOutput System Input System61-EN Terminology62-EN Indication Commander RUX-C800Case of Difficulty 63-EN SpecificationsComponents Dimensions64-EN