Alpine PXA-H800 Setting the Linear PCM PCM Mode, Adjusting the DVD Level DVD Level, 34-EN

Page 36

From a PC

Avoid stopping, pausing, switching the disc, cueing, fast-forwarding or switching the audio channel of this unit while making this adjustment. The setting is cancelled if the decode mode is switched.

When the Rear speaker is off in “Setting the Speaker System (Output System Select)” (page 13)/ “Setting the Speakers (Speaker Setup)/ Setting the Subwoofers” (page 14), this item cannot be set.

Effective only for Dolby Pro Logic II, EUPHONY and DTS (with rear signal).

Mixing the Low Range Audio of the Center with the Front L/R (Center Bass Split)

Turning on this function sends the Center channel low frequencies, equally to the front Left and Right speakers. This enhances the overall sound when using a small center speaker. This is used when the center speaker has a small diameter and cannot produce low frequency sounds. (Initial setting: “OFF”, “315 Hz”)

1 Click [ON] of “Center Bass Split.”

Turning this feature on mixes the audio signals output from the rear speakers with the front audio signals.

2 Click [ ] for “Frequency” and select and click a frequency you want from the pull-down menu.

Frequency:

200 Hz/225 Hz/250 Hz/280 Hz/315 Hz/350 Hz/400 Hz/450

Hz/500 Hz

Avoid stopping, pausing, switching the disc, cueing, fast-forwarding or switching the audio channel of this unit while making this adjustment. The effect may not be recognized easily depending on the decoding conditions.

When the Center speaker is off in “Setting the Speaker System (Output System Select)” (page 13)/ “Setting the Speakers (Speaker Setup)/Setting the Subwoofers” (page 14), this item cannot be set.

Effective only for Dolby Pro Logic II, EUPHONY and DTS (with Center signal).

Setting the Linear PCM (PCM Mode)

The output can be set to 2 or 3 channels when playing discs recorded in linear PCM. (Initial setting: “2ch”)

1 Click [ ] for “PCM Mode” and click either [2ch] or [3ch] from the pull-down menu.

2ch: 2ch Output (L/R)

3ch: 3ch Output (L/R/CENTER)

When the Center speaker is off in “Setting the Speaker System (Output System Select)” (page 13)/ “Setting the Speakers (Speaker Setup)/Setting the Subwoofers” (page 14), this item cannot be set.

Achieving Powerful High Volume Sound (Listening Mode)

With Dolby Digital, the dynamic range is compressed so that powerful sound can be achieved at regular volume levels. This compression can be cancelled to achieve an energetic sound with even greater power, like the sound in a movie theater. This function works only in the Dolby Digital mode. (Initial setting: “Standard”)

1 Click [ ] for “Listening Mode” and click either [Standard] or [Maximum] from the pull-down menu.

Standard: To enjoy the dynamic sound at regular volume

Maximum: To enjoy the dynamic sound at maximum volume

This feature is effective only for Dolby Digital.

Use this feature at a volume level at which you can still hear sound outside of the cabin.

Depending on the types of source, such as DVD software, this feature may be ineffective.

Adjusting the DVD Level (DVD Level)

The volume level for Dolby Digital, Dolby Pro Logic II, DTS, EUPHONY and PCM modes can be set. (Initial setting: “±0dB”)

1 Click [ ] for “DVD Level” and select and click the level of mode you want from the pull-down menu.

Adjustment modes: Dolby Digital/Dolby Pro Logic II/DTS /

 

PCM/EUPHONY

Level:

-10 to +10 dB (in 1 dB steps)

Avoid stopping, pausing, switching the disc, cueing, fast-forwarding or switching the audio channel of this unit while making this adjustment. The effect may not be recognized easily depending on the decoding conditions.

34-EN

Image 36
Contents PXA-H800 Page From a PC From the Commander Information Operating Instructions How to Read this Manual From a PC From the Commander Function listLocation of Controls PXA-H800Sound Manager for PXA-H800 RUX-C800 Commander sold separately Features About the Audio SettingBefore You First Use the Unit About OperatingInstalling Sound Manager for PXA-H800 About the Offline modeBefore installing, all active programs must be stopped Start Sound Manager for PXA-H800Using with Ai-NET Connections Turning Power On and OffInitial System Start-Up Operating the Sound Manager for PXA- H800 MenuAudio Adjustment Loading the ImprintEQ Measurement Data FileDownloading the Software Option Viewing the Version Information OptionSetting Defeat Switching the SourcesStoring the Preset Values Preset Store Recalling a Stored Setting Preset Call Setting the Speaker System Output System Select13-EN Setting the Speakers Speaker Setup/ Setting the Subwoofers Setting the AUX Input System AUX Input System Select14-EN Setting the AUX Input AUX Setting the Digital Input Digital AUXSetting the AUX Volume Input level AUX in Gain Adjusting the AUX Volume level AUX LevelBefore Performing Automatic Measurement Naming the AUX Input AUX Name16-EN Setting ImprintEQ 17-EN18-EN Adjusting and Saving the Target Curve Turning ImprintEQ On/OffSaving ImprintEQ Measurement Data on a 19-ENAdjusting the Time Correction Automatically Auto TCR Adjusting for Road Noise RoadEQ20-EN Click Auto TCR for Shortcut tab in the main menuWhen you click ON, select the level Turning RoadEQ On/Off21-EN Click on or OFF for RoadEQSetting MX Plus Ai-NET Mode Setting MX Plus Standalone Mode22-EN Setting the Graphic EQ 23-ENClick a frequency and drag up or down to adjust the level To adjust another channel, repeat Steps 4 through24-EN Displaying the data Click Show All DataSetting the Parametric EQ 25-ENClick P.EQ for Shortcut tab in the main menu Click P.EQ in the main menuAdjusting X-Over and Switching the Phases About the Crossover X-Over26-EN Crossover X-OverClick the indicator of Show 27-ENArrow indicating the dragging direction appears Adjusting the Time Correction TCR Calculation of time correctionEntering the time correction 28-ENSetting contents 0.00 to 20.00 ms in 0.05 ms steps Setting contents Inch29-EN Click either cm or inchSetting Euphony Euphony Click Multi Channel Manager of the Function switching tabSet and adjust 2ch Playback Mode, EUPHONY, Dolby Pro Logic 30-ENUsing Dolby Pro Logic II Dolby Pro Logic 31-ENMulti Channel Function Adjustment Procedure Multi Channel Setup32-EN Adjusting the Speaker Volume Level Output Level Adjusting the Acoustic Image BIMixing the Low Range Audio for the Rear Rear Mix 33-ENSetting the Linear PCM PCM Mode Achieving Powerful High Volume Sound Listening ModeAdjusting the DVD Level DVD Level 34-ENAdjusting Subwoofer Subwoofer Navigation Audio Volume Adjustment35-EN Adjusting the MX Plus Level MX Plus SETUP/LEVEL Adjustment Adjusting Balance Between Left and Right BalanceAdjusting Fader Between Front and Rear Fader Setting Defeat DefeatSetting the Speaker System System Select 37-ENSetting the Speakers Speaker Setup Setting the Subwoofer Output SW Channel38-EN OFF/ONSetting the AUX Input System AUX Input Setup Setting the AUX Input AUX39-EN Setting the Digital Input Digital AUX Setting the AUX Volume Input Level AUX in GainAdjusting the AUX Volume Level AUX Level 40-ENMixing Navi Audio Guidance Navi Mix Setup Rotate the Rotary encoder to make adjustmentWhen the setting is complete, press Naming the AUX Input AUX NameTurning ImprintEQ On/Off 42-ENBe sure to read before performing the automatic measurement Press and hold FUNC. for at least 2 secondsWhen Finished appears, press Rotary encoder 43-ENPress the Rotary encoder Setting the MX Plus Ai-NET Mode 44-ENSetting the MX Plus Standalone Mode To adjust another source, press and repeat Steps 8 through45-EN Press twice to go back to the screen for StepSetting the Equalizer Mode EQ Mode 46-ENG-EQ screen is displayed Select the channel you want to adjust by pressing Channel 47-EN48-EN Band FRONT/REAR/CENTER 1 toHz to 20kHz in 1/6 octave steps Hz to 200 Hz in 1/6 octave steps49-EN Front LOW Rear Center SUBWOOFER*1 Front HighFront L MID Front R MID 50-EN TCR screen is displayedSetting the Time Correction Adjustment Unit TCR Parameter To adjust another channel, repeat Steps 9 through51-EN Setting the 2-Channel Signal Playback Mode Mode Setting Euphony Euphony52-EN Using Dolby Pro Logic II Dolby Plii 53-ENDolby Plii screen is displayed Adjusting the Speaker Volume Level Output Level 54-ENSelect the channel by pressing Channel Adjusting the Acoustic Image BI Mixing the Low Range Audio for the Rear Rear Mix55-EN Setting the Linear PCM PCM Mode Achieving Powerful High Volume Sound Listening ModeAdjust the frequency by rotating the Rotary encoder 56-ENAdjusting the DVD Level DVD Level Lowering Volume Quickly MuteTurning the Back Light Off Black OUT function 57-ENAdjusting the Brightness Level of the Display Dimmer Level Adjusting the Brightness of the Display Dimmer58-EN Switching the Display Display mode switches for every push59-EN Press ViewSystem Configuration 60-ENOutput System Input SystemTerminology 61-ENIndication Commander RUX-C800 Case of Difficulty62-EN Specifications 63-ENDimensions 64-ENComponents