Alpine PXA-H800 owner manual 18-EN

Page 20

From a PC

12 Move the microphone to a spot specified in the screen and position it firmly.

The microphone should be placed at shoulder height.

13 Click [Measure]. When the measurement start screen appears, click [START].

Countdown will start.

During the 10 second countdown, go outside the vehicle and close the door.

A test signal will be output from the speakers to measure the acoustic characteristics of the cabin. Do not open any doors until the finish message appears on the screen. If external noise interferes with the measurement, click the [Measure] again to re-measure.

Measurement takes approximately 5 to 15 minutes.

If you want to stop measurement, click [CANCEL].

14 Click [OK] when a completed message appears.

15 When measurement for Position 1 is completed, move the microphone to the next measuring position and secure it following the guidance on the screen. When the microphone is properly located, repeat Step 13 following the guidance on the screen.

You can perform measurement from up to 6 listening positions.

We recommend that you should take measurements from at least 2 listening positions.

To close measurement, go to Step 16.

For more accurate measurement, you can make measurements from 6 listening positions. However, it takes approximately 70 minutes to complete the entire procedure. Therefore, be sure to charge the vehicle battery while taking measurements.

If no microphone is connected, a confirmation message will be displayed and measurement will not be carried out. Click [OK] to cancel the indication.

If you want to re-measure from the same position, click [Reset].

16 When measurement is complete, click [Result].

The result screen will be displayed.

The adjustment result when the Target Curve is “REFERENCE” will be displayed.

If you want to select another target curve, go to Step 17. If you want to save the adjustment result, go to Step 19.

17 Click [Target Curve Select].

The name of the curve currently selected.

The Target Curve Selection screen will be displayed.

18 Select and click the target curve you want. Then, click [OK].

The adjustment result for the selected Target Curve will be displayed.

REFERENCE:

Enjoy the rhythm and balance of music to the best acoustic effect, suitable for the vehicle interior.

Reference With Mid-range Comp.:

Select this if the tweeter and midrange speakers are installed in the dashboard, and mid or high range harshness is apparent.

LINEAR:

A linear (flat) acoustic effect is actualized. This setting recreates the balanced sound of a studio listening room.

USERS:

You can select this only when you have adjusted the curve. Refer to “Adjusting and Saving the Target Curve” (page 19).

If you are not satisfied with the measurement result, click [Re- Measure] to perform measurement again.

19 Click [Send Filter].

The Memory selection screen will be displayed.

18-EN

Image 20
Contents PXA-H800 Page From a PC From the Commander Information Operating Instructions How to Read this Manual From a PC From the Commander Function listSound Manager for PXA-H800 Location of ControlsPXA-H800 RUX-C800 Commander sold separately Features About the Audio SettingBefore You First Use the Unit About OperatingInstalling Sound Manager for PXA-H800 About the Offline modeBefore installing, all active programs must be stopped Start Sound Manager for PXA-H800Using with Ai-NET Connections Turning Power On and OffInitial System Start-Up Operating the Sound Manager for PXA- H800 MenuAudio Adjustment Loading the ImprintEQ Measurement Data FileDownloading the Software Option Viewing the Version Information OptionStoring the Preset Values Preset Store Setting DefeatSwitching the Sources 13-EN Recalling a Stored Setting Preset CallSetting the Speaker System Output System Select 14-EN Setting the Speakers Speaker Setup/ Setting the SubwoofersSetting the AUX Input System AUX Input System Select Setting the AUX Input AUX Setting the Digital Input Digital AUXSetting the AUX Volume Input level AUX in Gain Adjusting the AUX Volume level AUX Level16-EN Before Performing Automatic MeasurementNaming the AUX Input AUX Name Setting ImprintEQ 17-EN18-EN Adjusting and Saving the Target Curve Turning ImprintEQ On/OffSaving ImprintEQ Measurement Data on a 19-ENAdjusting the Time Correction Automatically Auto TCR Adjusting for Road Noise RoadEQ20-EN Click Auto TCR for Shortcut tab in the main menuWhen you click ON, select the level Turning RoadEQ On/Off21-EN Click on or OFF for RoadEQ22-EN Setting MX Plus Ai-NET ModeSetting MX Plus Standalone Mode Setting the Graphic EQ 23-ENClick a frequency and drag up or down to adjust the level To adjust another channel, repeat Steps 4 through24-EN Displaying the data Click Show All DataSetting the Parametric EQ 25-ENClick P.EQ for Shortcut tab in the main menu Click P.EQ in the main menuAdjusting X-Over and Switching the Phases About the Crossover X-Over26-EN Crossover X-OverArrow indicating the dragging direction appears Click the indicator of Show27-EN Adjusting the Time Correction TCR Calculation of time correctionEntering the time correction 28-ENSetting contents 0.00 to 20.00 ms in 0.05 ms steps Setting contents Inch29-EN Click either cm or inchSetting Euphony Euphony Click Multi Channel Manager of the Function switching tabSet and adjust 2ch Playback Mode, EUPHONY, Dolby Pro Logic 30-ENUsing Dolby Pro Logic II Dolby Pro Logic 31-EN32-EN Multi Channel Function Adjustment ProcedureMulti Channel Setup Adjusting the Speaker Volume Level Output Level Adjusting the Acoustic Image BIMixing the Low Range Audio for the Rear Rear Mix 33-ENSetting the Linear PCM PCM Mode Achieving Powerful High Volume Sound Listening ModeAdjusting the DVD Level DVD Level 34-EN35-EN Adjusting Subwoofer SubwooferNavigation Audio Volume Adjustment Adjusting the MX Plus Level MX Plus SETUP/LEVEL Adjustment Adjusting Balance Between Left and Right BalanceAdjusting Fader Between Front and Rear Fader Setting Defeat DefeatSetting the Speaker System System Select 37-ENSetting the Speakers Speaker Setup Setting the Subwoofer Output SW Channel38-EN OFF/ON39-EN Setting the AUX Input System AUX Input SetupSetting the AUX Input AUX Setting the Digital Input Digital AUX Setting the AUX Volume Input Level AUX in GainAdjusting the AUX Volume Level AUX Level 40-ENMixing Navi Audio Guidance Navi Mix Setup Rotate the Rotary encoder to make adjustmentWhen the setting is complete, press Naming the AUX Input AUX NameTurning ImprintEQ On/Off 42-ENBe sure to read before performing the automatic measurement Press and hold FUNC. for at least 2 secondsPress the Rotary encoder When Finished appears, press Rotary encoder43-EN Setting the MX Plus Ai-NET Mode 44-ENSetting the MX Plus Standalone Mode To adjust another source, press and repeat Steps 8 through45-EN Press twice to go back to the screen for StepG-EQ screen is displayed Setting the Equalizer Mode EQ Mode46-EN Select the channel you want to adjust by pressing Channel 47-EN48-EN Band FRONT/REAR/CENTER 1 toHz to 20kHz in 1/6 octave steps Hz to 200 Hz in 1/6 octave stepsFront L MID Front R MID 49-ENFront LOW Rear Center SUBWOOFER*1 Front High 50-EN TCR screen is displayed51-EN Setting the Time Correction Adjustment Unit TCR ParameterTo adjust another channel, repeat Steps 9 through 52-EN Setting the 2-Channel Signal Playback Mode ModeSetting Euphony Euphony Dolby Plii screen is displayed Using Dolby Pro Logic II Dolby Plii53-EN Select the channel by pressing Channel Adjusting the Speaker Volume Level Output Level54-EN 55-EN Adjusting the Acoustic Image BIMixing the Low Range Audio for the Rear Rear Mix Setting the Linear PCM PCM Mode Achieving Powerful High Volume Sound Listening ModeAdjust the frequency by rotating the Rotary encoder 56-ENAdjusting the DVD Level DVD Level Lowering Volume Quickly MuteTurning the Back Light Off Black OUT function 57-EN58-EN Adjusting the Brightness Level of the Display Dimmer LevelAdjusting the Brightness of the Display Dimmer Switching the Display Display mode switches for every push59-EN Press ViewSystem Configuration 60-ENOutput System Input SystemTerminology 61-EN62-EN Indication Commander RUX-C800Case of Difficulty Specifications 63-ENComponents Dimensions64-EN