Alpine PXA-H800 owner manual Setting the Equalizer Mode EQ Mode, 46-EN, G-EQ screen is displayed

Page 48

From the Commander

9 Select the level you want by rotating the [Rotary encoder], and press the [Rotary encoder].

Compressed 1 to 3:

This corrects information lost in the compression process. This reproduces a well-balanced sound close to the original. By supplementing mid- to high- frequency sound data, the sound is reproduced with more brightness and ambience.

Music 1 to 3:

Lower register sounds (drums, bass, etc.) and vocals are emphasized for clean and clear output.

Cinema:

Video dialogue is reproduced more clearly. Action movies are reproduced with more powerful sound.

Action:

Action movies are reproduced with more powerful sound.

Drama/Talk:

The dialogue portion of a video is reproduced more clearly.

When “Non Effect” is selected, MX Plus becomes disabled.

Sources to be set vary depending on the system set in “Setting the AUX Input System (AUX Input Setup)” (page 39).

10 To adjust another source, press [ ] and repeat Steps 8 through 9.

You can listen with Defeat OFF (adjusted setup values) or with Defeat ON (Initial value) to compare, by following the steps below.

1Press and hold the [Rotary Encoder] for 2 seconds or longer while in the adjustment mode.

2Rotate the [Rotary Encoder] to switch on/off Defeat, and listen to compare.

3To exit, select “OFF” and then press [ ].

11 When the setting is complete, press and hold [ ] for at least 2 seconds.

If [ ] is pressed during setting, the unit returns to the previous item.

This function is not available when Defeat is set to ON.

After the setting, it is recommended to store the setting contents on the unit. For details, refer to “Storing the Preset Values (Preset Store)” (page 36).

Setting the Equalizer Mode (EQ Mode)

You can choose either the Graphic EQ or the Parametric EQ for the equalizer mode. You can also turn it off. (Initial setting: “OFF”)

1 Press [FUNC.].

2 Rotate the [Rotary encoder] to select “Sound Field Adj.,” and then press the [Rotary encoder].

3 Rotate the [Rotary encoder] to select “Setup,” and then press the [Rotary encoder].

4 Rotate the [Rotary encoder] to select “EQ Mode,” and then press the [Rotary encoder].

5 Select either “G.EQ,” “P.EQ,” or “OFF” by rotating the [Rotary encoder], and press the [Rotary encoder].

EQ MODE

G.EQ

G.EQ: Graphic EQ is used.

P.EQ: Parametric EQ is used.

OFF: EQ mode is disabled.

6 When the setting is complete, press and hold [ ] for at least 2 seconds.

If [ ] is pressed during setting, the unit returns to the previous item.

This function is not available when Defeat is set to ON.

After the setting, it is recommended to store the setting contents on the unit. For details, refer to “Storing the Preset Values (Preset Store)” (page 36).

Setting the Graphic EQ

The graphic equalizer allows you to modify the sound using 31 bands each for the front (left and right), rear (left and right) and center speakers. An additional 10 bands are available for the subwoofer. This allows you to customize the sound to suit your taste.

Set “Setting the Equalizer Mode (EQ Mode)” on page 46 to “G.EQ.”

1 Press [FUNC.].

2 Rotate the [Rotary encoder] to select “Sound Field Adj.,” and then press the [Rotary encoder].

3 Rotate the [Rotary encoder] to select “EQ Adjustment,” and then press the [Rotary encoder].

The G-EQ screen is displayed.

4 Press and hold [CHANNEL] for at least 2 seconds. Rotate the [Rotary encoder] to select either “L+R” or “L or R,” and press the [Rotary encoder].

L or R: Channels Right and Left can be set independently.

L+R: Both Right and Left channels are set at the same value (The initial setting).

When you switch from “L or R” to “L+R,” choose which adjustment of the R and L channels to be applied.

1Select either “L R” or “R L” by rotating the [Rotary encoder], and press the [Rotary encoder].

L R: The adjustment of the Left channel is to be applied to both Right and Left channels.

R L: The adjustment of the Right channel is to be applied to both Right and Left channels.

46-EN

Image 48
Contents PXA-H800 Page From a PC From the Commander Information Operating Instructions How to Read this Manual From a PC From the Commander Function listLocation of Controls PXA-H800Sound Manager for PXA-H800 RUX-C800 Commander sold separately Features About the Audio SettingBefore You First Use the Unit About OperatingInstalling Sound Manager for PXA-H800 About the Offline modeBefore installing, all active programs must be stopped Start Sound Manager for PXA-H800Using with Ai-NET Connections Turning Power On and OffInitial System Start-Up Operating the Sound Manager for PXA- H800 MenuAudio Adjustment Loading the ImprintEQ Measurement Data FileDownloading the Software Option Viewing the Version Information OptionSetting Defeat Switching the SourcesStoring the Preset Values Preset Store Recalling a Stored Setting Preset Call Setting the Speaker System Output System Select13-EN Setting the Speakers Speaker Setup/ Setting the Subwoofers Setting the AUX Input System AUX Input System Select14-EN Setting the AUX Input AUX Setting the Digital Input Digital AUXSetting the AUX Volume Input level AUX in Gain Adjusting the AUX Volume level AUX LevelBefore Performing Automatic Measurement Naming the AUX Input AUX Name16-EN Setting ImprintEQ 17-EN18-EN Adjusting and Saving the Target Curve Turning ImprintEQ On/OffSaving ImprintEQ Measurement Data on a 19-ENAdjusting the Time Correction Automatically Auto TCR Adjusting for Road Noise RoadEQ20-EN Click Auto TCR for Shortcut tab in the main menuWhen you click ON, select the level Turning RoadEQ On/Off21-EN Click on or OFF for RoadEQSetting MX Plus Ai-NET Mode Setting MX Plus Standalone Mode22-EN Setting the Graphic EQ 23-ENClick a frequency and drag up or down to adjust the level To adjust another channel, repeat Steps 4 through24-EN Displaying the data Click Show All DataSetting the Parametric EQ 25-ENClick P.EQ for Shortcut tab in the main menu Click P.EQ in the main menuAdjusting X-Over and Switching the Phases About the Crossover X-Over26-EN Crossover X-OverClick the indicator of Show 27-ENArrow indicating the dragging direction appears Adjusting the Time Correction TCR Calculation of time correctionEntering the time correction 28-ENSetting contents 0.00 to 20.00 ms in 0.05 ms steps Setting contents Inch29-EN Click either cm or inchSetting Euphony Euphony Click Multi Channel Manager of the Function switching tabSet and adjust 2ch Playback Mode, EUPHONY, Dolby Pro Logic 30-ENUsing Dolby Pro Logic II Dolby Pro Logic 31-ENMulti Channel Function Adjustment Procedure Multi Channel Setup32-EN Adjusting the Speaker Volume Level Output Level Adjusting the Acoustic Image BIMixing the Low Range Audio for the Rear Rear Mix 33-ENSetting the Linear PCM PCM Mode Achieving Powerful High Volume Sound Listening ModeAdjusting the DVD Level DVD Level 34-ENAdjusting Subwoofer Subwoofer Navigation Audio Volume Adjustment35-EN Adjusting the MX Plus Level MX Plus SETUP/LEVEL Adjustment Adjusting Balance Between Left and Right BalanceAdjusting Fader Between Front and Rear Fader Setting Defeat DefeatSetting the Speaker System System Select 37-ENSetting the Speakers Speaker Setup Setting the Subwoofer Output SW Channel38-EN OFF/ONSetting the AUX Input System AUX Input Setup Setting the AUX Input AUX39-EN Setting the Digital Input Digital AUX Setting the AUX Volume Input Level AUX in GainAdjusting the AUX Volume Level AUX Level 40-ENMixing Navi Audio Guidance Navi Mix Setup Rotate the Rotary encoder to make adjustmentWhen the setting is complete, press Naming the AUX Input AUX NameTurning ImprintEQ On/Off 42-ENBe sure to read before performing the automatic measurement Press and hold FUNC. for at least 2 secondsWhen Finished appears, press Rotary encoder 43-ENPress the Rotary encoder Setting the MX Plus Ai-NET Mode 44-ENSetting the MX Plus Standalone Mode To adjust another source, press and repeat Steps 8 through45-EN Press twice to go back to the screen for StepSetting the Equalizer Mode EQ Mode 46-ENG-EQ screen is displayed Select the channel you want to adjust by pressing Channel 47-EN48-EN Band FRONT/REAR/CENTER 1 toHz to 20kHz in 1/6 octave steps Hz to 200 Hz in 1/6 octave steps49-EN Front LOW Rear Center SUBWOOFER*1 Front HighFront L MID Front R MID 50-EN TCR screen is displayedSetting the Time Correction Adjustment Unit TCR Parameter To adjust another channel, repeat Steps 9 through51-EN Setting the 2-Channel Signal Playback Mode Mode Setting Euphony Euphony52-EN Using Dolby Pro Logic II Dolby Plii 53-ENDolby Plii screen is displayed Adjusting the Speaker Volume Level Output Level 54-ENSelect the channel by pressing Channel Adjusting the Acoustic Image BI Mixing the Low Range Audio for the Rear Rear Mix55-EN Setting the Linear PCM PCM Mode Achieving Powerful High Volume Sound Listening ModeAdjust the frequency by rotating the Rotary encoder 56-ENAdjusting the DVD Level DVD Level Lowering Volume Quickly MuteTurning the Back Light Off Black OUT function 57-ENAdjusting the Brightness Level of the Display Dimmer Level Adjusting the Brightness of the Display Dimmer58-EN Switching the Display Display mode switches for every push59-EN Press ViewSystem Configuration 60-ENOutput System Input SystemTerminology 61-ENIndication Commander RUX-C800 Case of Difficulty62-EN Specifications 63-ENDimensions 64-ENComponents