NordicTrack NTL99030 user manual Troubleshooting, Solution

Page 23

TROUBLESHOOTING

Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and follow the steps listed. If further assistance is needed, please call our Customer Service Department toll-

free at 1-888-825-2588, Monday through Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays).

PROBLEM: The power does not turn on

SOLUTION: a. Make sure that the power cord is plugged into a surge suppressor, and that the surge suppressor

is plugged into a properly grounded outlet (see page 8). Use only a single-outlet surge suppressor that meets all of the specifications described on page 8. Important: The treadmill is not compatible with GFCI-equipped outlets.

b. After the power cord has been plugged in, make sure that the key is fully inserted into the console.

c.Check the on/off circuit breaker located on the treadmill frame near the power cord. If the switch protrudes as shown, the on/off circuit breaker has tripped. To reset the on/off circuit breaker, wait for five minutes and then press the switch back in.

PROBLEM: The power turns off during use

c

Tripped

Reset

SOLUTION: a. Check the on/off circuit breaker (see the drawing above). If the on/off circuit breaker has tripped, wait for five minutes and then press the switch back in.

b. Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for five minutes, and then plug it back in.

c. Remove the key from the console. Reinsert the key fully into the console.

d. If the treadmill still will not run, please call our Customer Service Department, toll-free.

PROBLEM: The displays of the console do not function properly

SOLUTION:

a. Remove the key from the console and

unplug the

 

power cord.

Carefully tip the treadmill down as shown

in drawing a. Remove the Screws (83) from the hood. Raise the Uprights (69) and carefully remove the hood.

Locate the Reed Switch (10) and the Magnet (7) on

 

the left side of the Pulley (8). Turn the Pulley until the

 

Magnet is aligned with the Reed Switch.

Make sure

that the gap between the Magnet and the Reed

 

Switch is about 1/8”.

If necessary, loosen the Screw

(27)and move the Reed Switch slightly. Retighten the Screw. Re-attach the hood, and run the treadmill for a few minutes to check for a correct speed reading.

a

 

 

83

69

 

1/8”

8

27

 

10

7

Top

 

View

 

23

Page 22 Page 24
Image 23
Page 22 Page 24
Contents Customer HOT Line To Avoid DELAYS, Please Call Direct to OUR TollTable of Contents Same circuit. Do not use an extension cord Important PrecautionsUse the treadmill only as described Both men and womenNever insert or drop any object into any opening Using themRight Side Using the treadmillBefore YOU Begin Left Side100 102 Worn AssemblyAssembly requires two people Make sure that Extension Legs 102 remain in the UprightsShown Make sure that no wires are pinchedTighten all four Handrail Bolts Mill to protect the floorThis product must be grounded.If it should malfunc HOW to Plug in the Power CordPerformant Lube Use only a single-outlet surge suppressor that isVideo Features of the ConsoleHOW to USE the Manual Mode HOW to Turn on the PowerMeasure your heart rate, if desired Follow your progress with the displays ProgramTraining Zone Incline/Distance DisplayStart the program HOW to USE Preset ProgramsSelect one of the four preset programs 7Turn on the fans if desiredTurn on the fans if desired Press the Start button or the Speed + button HOW to Create Custom ProgramsWhen the program has ended, remove the key Select one of the custom programsFollow your progress with the displays HOW to USE Custom ProgramsVideocassettes HOW to Connect Your Portable CD PlayerHOW to Connect Your Portable Stereo Audio 5mm Cable Adapter HOW to Connect Your Home StereoHOW to Connect Your Computer Plug the adapter into the Line OUT jack on your stereoVCR HOW to Connect Your VCRPrograms Console Next settings of the CD or video programTings of the CD or video program Start button or the SpeedFollow the on-line instructions to start Program HOW to USE Programs Directly from OUR WEB SiteNext settings of the program 9When the program has ended, remove the keyOptional Chest Pulse Sensor Information MODE/DEMO ModeShould be blank If a d apHOW to Lower the Treadmill for USE HOW to Fold and Move the TreadmillHOW to Fold the Treadmill for Storage HOW to Move the TreadmillSolution TroubleshootingShifted to the left Problem The walking belt slows when walked onPower Cord If the walking belt hasExercise Frequency Conditioning GuidelinesExercise Intensity Workout GuidelinesQty Description 109 Power Cord Grommet Ordering Replacement Parts105 Silver Screw Thick Base Pad 106 Extension Leg Assembly 107 Fan Blue Wire, 2F 108 Book HolderR0503A Exploded DRAWING-Model No. NTL99030Exploded DRAWING-Model No. NTL99030 Icon Health & FITNESS, INC., 1500 S W., LOGAN, UT Limited WarrantyWhat is COVERED-The entire NordicTrack Part No R0503A
Top Page Image Contents