NordicTrack NTL99030 user manual Tighten all four Handrail Bolts, Mill to protect the floor, Shown

Page 7

4. Cut the plastic tie holding the Upright Wire Harness (98).

4

 

 

Have a second person hold the Handrails (66) near the

 

 

 

 

81

Uprights (69). Connect the Upright Wire Harness to the

 

 

 

 

 

wires extending from the Console Base (81).

The connec-

 

 

tors should slide together easily and snap into place.

 

 

98

If they do not, turn one connector and try again.

Then,

 

 

insert the connectors and the Upright Wire Harness into

 

 

 

the hole in the right Upright. Set the Handrails on the

 

 

 

Uprights, being careful not to pinch the wires.

 

 

 

5. Insert two Handrail Bolts (78) with Handrail Spacers (77)

 

66

69

 

 

 

into the right Upright (69) and the right Handrail (66).

Be

 

 

careful not to pinch the wires.

Make sure that the

 

 

Handrail Spacers are flush against the right Upright, with

5

 

 

the thick sides facing the center of the treadmill, as shown

 

 

 

 

 

in the inset drawing. Next, lift the right Handrail (66) slightly

 

 

 

and align the Bolts with the holes in the Handrail. Thread

 

 

 

the Bolts into the Handrail.

Do not tighten the Bolts yet.

 

69

 

 

 

 

 

Attach the left Handrail (not shown) in the same way.

 

66

77

Then,

tighten all four Handrail Bolts (78).

 

Thick

 

 

 

 

 

 

 

6. Make sure that all parts are properly tightened before

 

 

Side

 

 

 

you use the treadmill. Place a mat beneath the tread-

 

77

78

mill to protect the floor.

 

 

 

 

If you purchase the optional chest pulse sensor (see

1

82

 

page 21), follow the steps below to install the receiver

 

included with the chest pulse sensor.

 

 

 

 

1. Make sure that the power cord is unplugged.

Remove

 

 

the indicated screws from the Console Back (88).

 

 

 

(Important: The screws may be different lengths; note

 

 

 

the original locations of the screws.)

Next, remove the

88

 

Console Back.

 

 

 

 

 

 

Screws

 

 

 

 

 

2. Peel the paper off the pad on the bottom of the Receiver

 

2

(A).Turn the Receiver so the cylinder is on the side

 

 

shown,

and press the Receiver into the Console Base (81)

 

in the indicated location.

 

A

 

 

 

 

 

 

Cylinder

 

 

 

81

3. Connect the included Short Jumper Wire (B) to the wire on

 

3

the Receiver (A). Connect the other end of the Short

 

 

PLS2

Jumper Wire to the PLS2 jack on the underside of the

 

 

Jack

Console (82). (Note: If there is already a wire in the PLS2

82

jack, unplug it.) Discard the other wires included with the

receiver. Use the included wire tie to secure the wires, if

 

 

needed.

 

 

 

Make sure that no wires are pinched.

See step 1.

Reattach the Console (82) with the screws.

 

Important: If

the screws are not in their original locations, the

 

B

Console may be damaged.

 

 

 

 

A

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Customer HOT Line To Avoid DELAYS, Please Call Direct to OUR TollTable of Contents Same circuit. Do not use an extension cord Important PrecautionsUse the treadmill only as described Both men and womenNever insert or drop any object into any opening Using themRight Side Using the treadmillBefore YOU Begin Left Side100 102 Worn AssemblyAssembly requires two people Make sure that Extension Legs 102 remain in the UprightsShown Make sure that no wires are pinchedTighten all four Handrail Bolts Mill to protect the floorThis product must be grounded.If it should malfunc HOW to Plug in the Power CordPerformant Lube Use only a single-outlet surge suppressor that isVideo Features of the ConsoleHOW to USE the Manual Mode HOW to Turn on the PowerMeasure your heart rate, if desired Follow your progress with the displays ProgramTraining Zone Incline/Distance DisplayStart the program HOW to USE Preset ProgramsSelect one of the four preset programs 7Turn on the fans if desiredTurn on the fans if desired Press the Start button or the Speed + button HOW to Create Custom ProgramsWhen the program has ended, remove the key Select one of the custom programsFollow your progress with the displays HOW to USE Custom ProgramsHOW to Connect Your Portable Stereo HOW to Connect Your Portable CD PlayerVideocassettes Audio 5mm Cable Adapter HOW to Connect Your Home StereoHOW to Connect Your Computer Plug the adapter into the Line OUT jack on your stereoPrograms HOW to Connect Your VCRVCR Console Next settings of the CD or video programTings of the CD or video program Start button or the SpeedFollow the on-line instructions to start Program HOW to USE Programs Directly from OUR WEB SiteNext settings of the program 9When the program has ended, remove the keyOptional Chest Pulse Sensor Information MODE/DEMO ModeShould be blank If a d apHOW to Lower the Treadmill for USE HOW to Fold and Move the TreadmillHOW to Fold the Treadmill for Storage HOW to Move the TreadmillSolution TroubleshootingShifted to the left Problem The walking belt slows when walked onPower Cord If the walking belt hasExercise Frequency Conditioning GuidelinesExercise Intensity Workout GuidelinesQty Description 109 Power Cord Grommet Ordering Replacement Parts105 Silver Screw Thick Base Pad 106 Extension Leg Assembly 107 Fan Blue Wire, 2F 108 Book HolderR0503A Exploded DRAWING-Model No. NTL99030Exploded DRAWING-Model No. NTL99030 Icon Health & FITNESS, INC., 1500 S W., LOGAN, UT Limited WarrantyWhat is COVERED-The entire NordicTrack Part No R0503A
Top Page Image Contents