3. Cut the rubber band securing the Upright Wire Harness |
| 3 | 98 | ||
(98). Have a second person hold the console assembly |
| ||||
|
| ||||
|
|
| |||
near the Uprights (69). Connect the Upright Wire Harness |
| 81 | |||
to the wires extending from the Console Base (81). | The |
| |||
connectors should slide together easily and snap into |
|
|
| ||
place. If they do not, turn one connector and try again. |
|
|
| ||
Insert the connectors and the Upright Wire Harness down |
|
| 98 | ||
into the | right Upright, and then set the | console assembly |
|
| |
on the Uprights. | Be careful not to pinch the wires. |
|
| ||
|
|
|
| 69 |
|
|
|
| Console |
|
|
|
|
| Assembly |
|
|
4. Insert a Handrail (118) into the right side of the console |
| 4 |
|
| |
assembly as shown. (Note: It may be helpful to twist the |
|
|
| ||
|
|
|
| ||
Handrail as you insert it.) Next, insert two 4 1/2” Bolts (78) |
|
|
| ||
with Handrail Spacers (77) into the right Upright (69) and |
|
|
| ||
the Handrail. | Be careful not to pinch the wires. | Make |
|
|
|
sure that the Handrail Spacers are flush against the right |
|
|
|
| |
Upright, with the thicker sides of the Handrail Spacers to- |
|
| 69 |
| |
ward the center of the treadmill, as shown in the inset |
|
| Thick | ||
|
| 77 | |||
drawing. |
|
|
|
| Side |
Next, lift the console assembly and the Handrail (118) |
| 118 |
|
| |
|
|
|
| ||
slightly and align the 4 1/2” Bolts (78) with the holes in the |
|
|
| ||
Handrail. Thread the Bolts into the Handrail until the |
| 77 | 78 |
| |
heads of the Bolts are against the right Upright (69). | Do |
| |||
|
|
| |||
not tighten the Bolts yet. |
| Console |
|
| |
|
|
| Assembly |
|
|
Attach the other Handrail (not shown) in the same way. |
|
|
|
| |
Note: There are no wires on the left side. |
|
|
|
| |
5. With the help of a second person, carefully tip the |
| 5 |
|
| |
Uprights (69) down to the position shown. | Make sure that |
|
| ||
|
| 99 | |||
the Extension Legs (102) remain in the Uprights. |
|
|
| ||
|
|
|
| ||
Attach each Extension Leg (102) with two 1” Tek Screws |
| 69 |
| 53 | |
|
|
| |||
(47). Next, align the lower ends of the Handrails (118) |
|
|
| ||
with the holes in the base of the Uprights (69). Attach |
|
|
|
| |
each Handrail with a 4” Bolt (53) as shown. | Note: The |
|
| 47 | |
Bolts must be at an angle that matches the angle of |
| 99 |
|
| |
the Handrails, as shown in the inset drawing. |
|
| 102 | 99 | |
|
|
| 53 |
| |
|
|
|
|
| |
With the help of a second person, carefully tip the |
|
| |
Uprights (69) back to the vertical position. See step 4. |
|
| |
Tighten the four 4 1/2” Bolts (78). | 118 | 47 | |
Note: One replacement Base Pad (99) may be included. | 102 | 53 | |
99 | |||
Use the Base Pad to replace any Base Pad that becomes |
| ||
| 118 | ||
worn. |
|
7