PART | R0702A |
To locate the parts listed below, refer to the EXPLODED DRAWING attached in the center of this manual.
Key No. | Qty. | Description | Key No. Qty. | Description |
| |
1 | 2 | Foot Rail Insert |
| 52 | 1 | Walking Platform |
2 | 2 | Foot Rail |
| 53 | 6 | Platform Screw |
3 | 2 | Foot Rail Cap Screw |
| 54 | 2 | Rear Platform Screw |
4 | 1 | Left Foot Rail Cap |
| 55 | 2 | Rear Isolator |
5 | 2 | Frame Pivot Bolt |
| 56 | 5 | Ground Screw/Controller Screw |
6 | 2 | Frame Pivot Spacer |
| 57 | 1 | Ground Wire |
7 | 1 | Magnet |
| 58 | 1 | Rear Endcap |
8 | 1 | Front Roller/Pulley |
| 59 | 2 | Rear Roller Adj. Bolt |
9 | 5 | Frame Pivot Nut |
| 60 | 1 | Warning Decal |
10 | 1 | Reed Switch/Sensor Wire |
| 61 | 1 | Allen Wrench |
11 | 4 |
| 62 | 1 | Rear Roller | |
12 | 1 | Reed Switch Clip | 63** | 1 | Optional Chest Pulse Strap | |
13 | 1 | Lift Frame | 64** | 1 | Optional Chest Pulse | |
14 | 2 | Ground Bracket |
| 65 | 2 | Handrail Spacer |
15* | 1 | Idler Assembly |
| 66 | 1 | Handrail |
16 | 1 | Motor/Pulley/Flywheel/Fan |
| 67 | 2 | Endcap Clip |
17 | 1 | Idler Arm |
| 68 | 1 | Lock Knob |
18 | 1 | Motor Belt |
| 69 | 1 | Upright |
19 | 1 | Idler Pulley |
| 70 | 1 | Lock Knob Sleeve |
20 | 1 | Tension Bolt |
| 71 | 1 | Spring |
21 | 1 | Incline Motor Bolt |
| 72 | 1 | Lock Pin Collar |
22 | 2 | Motor Bolt |
| 73 | 1 | Pin Clip |
23 | 1 | Hood |
| 74 | 1 | Lock Pin |
24 | 1 | Short Incline Motor Bolt |
| 75 | 4 | Handrail Bushing |
25 | 4 | Plastic |
| 76 | 1 | Pulse Grip Assembly |
26 | 1 | Power Board |
| 77 | 4 | Handrail Washer |
27 | 15 | Screw |
| 78 | 4 | Handrail Bolt |
28 | 1 | Pulley Spacer |
| 79 | 2 | Upright Endcap |
29 | 1 | Controller |
| 80 | 1 | Pulley Nut |
30 | 1 | Electronics Plate |
| 81 | 1 | Console Base |
31 | 1 | 8” Wire Harness |
| 82 | 1 | Console |
32 | 1 | Front Roller Adj. Bolt |
| 83 | 2 | Belly Pan Screw (Short) |
33* | 1 | Latch Assembly |
| 84 | 1 | Key/Clip |
34 | 3 | Roller Washer |
| 85 | 1 | iFIT.com Wire |
35 | 1 | Front Roller Nut |
| 86 | 1 | Jack |
36 | 1 | Incline Motor |
| 87 | 2 | Handrail Endcap |
37 | 1 | Incline Motor Stop |
| 88 | 1 | Console Back |
38 | 1 | Belly Pan |
| 89 | 1 | Releaseable Tie |
39 | 2 | Belly Pan Screw (Long) |
| 90 | 10 | 1” Console Screw |
40 | 2 | Static Decal |
| 91 | 3 | Cable Tie Clamp |
41 | 1 | Circuit Breaker |
| 92 | 1 | 8” Cable Tie |
42 | 1 | Power Cord |
| 93 | 2 | Lift Pivot Bolt |
43 | 1 | On/Off Switch |
| 94 | 2 | Wheel Bolt |
44 | 1 | Left Endcap Insert |
| 95 | 2 | Wheel |
45 | 4 | Belt Guide Screw |
| 96 | 1 | Right Endcap Insert |
46 | 1 | Belt Guide |
| 97 | 1 | Grommet |
47 | 4 | Isolator |
| 98 | 1 | Upright Wire Harness |
48 | 1 | Idler Spring |
| 99 | 5 | Base Pad |
49 | 16 | Fastener |
| 100 | 13 | Screw |
50 | 1 | Belly Pan |
| 101 | 1 | Tension Nut |
51 | 1 | Right Foot Rail Cap |
| 102 | 2 | Extension Leg |
30