Gold's Gym GGTL78609.0 manual Uprights. Be careful not to pinch any wires

Page 10

11. Identify the Left Accessory Tray (112) and the	11	2		2
Right Accessory Tray (116). Attach the Left	11	2		2
Accessory Tray and the Right Accessory Tray
to the console assembly with eight #8 x 1/2"			112	116
Screws (2).			112	116
			Console
			Assembly
12. Have a second person hold the console assem-	12			Console
bly near the Uprights (85, 86).				Assembly
Connect the Upright Wire (97) to the console
wire extending from the console assembly. See
the inset drawing. The connectors should
slide together easily and snap into place. If
they do not, turn one connector and try again. IF
THE CONNECTORS ARE NOT CONNECTED
PROPERLY, THE CONSOLE MAY BE DAM-
AGED WHEN THE POWER IS TURNED ON.		85		Console
Remove the wire tie from the Upright Wire (97).		85		Console
Insert the excess wire into the Right Upright (86)				Wire
as you set the console assembly on the		Console		97
Uprights. Be careful not to pinch any wires.		Console	Wire	97
		Wire	Wire	86
		97	Tie
		97

13.Attach the console assembly to the Uprights (85, 86) with four 3/8" x 1 1/4" Bolts (7) and four 3/8" Star Washers (10). Start all four Bolts be- fore tightening any of them.

See steps 4 and 6. Fully tighten the four 3/8" x 4 1/2" Bolts (6).

13 Console Assembly

107	10	7	10
	85	10	7 86
		10	7 86
		7

10

Image 10

Contents Mon.-Fri a.m.-6 p.m. MT Sat a.m.-4 p.m. MT QUESTIONS?Model No. GGTL78609.0 Serial No On the WEBTable of Contents Important Precautions Pulse sensor is not a medical devicePage Before YOU Begin Assembly Do not fully fold the Frame yetTighten the Nut the Wheel must turn freely Ful not to pinch the Upright WireSpacer 92. Be careful not to pinch Upright Wire Not fully tighten the Bolts yetWheel must turn freely Console assembly. See the inset drawing Bar. See the inset drawing. The connectorsNo wires are pinched. Do not fully tighten Should slide together easily and snap intoUprights. Be careful not to pinch any wires 108 Next, hold the receiver so that the antenna is HOW to Plug in the Power Cord Operation and AdjustmentPRE-LUBRICATED Walking Belt Console Diagram Features of the ConsoleHOW to USE the Manual Mode HOW to Turn on the PowerInsert the key into the console Distance Follow your progress with the displays. The matrix-When youTurn on the fans if desired Select a preset workout HOW to USE a Preset WorkoutStart the workout HOW to Create a Custom Workout Select a custom workoutHOW to USE a Custom Workout HOW to USE AN Ifit Workout Insert an iFit card and select a workoutHOW to USE the Stereo Sound System Information ModeMake sure that the audio wire is fully plugged Optional Chest Pulse Sensor HOW to Fold and Move the Treadmill HOW to Move the TreadmillHOW to Lower the Treadmill for USE Troubleshooting Problem The power turns off during useProblem The walking belt slows when walked on TopProblem Solution Workout Guidelines Exercise GuidelinesExercise Intensity Exercise FrequencyPart LIST-Model No. GGTL78609.0 Key No. Qty DescriptionQty Exploded Drawing A-Model No. GGTL78609.0 R0709A Exploded Drawing B-Model No. GGTL78609.0 R0709A Exploded Drawing C-Model No. GGTL78609.0 R0709A 10 101 100 104 124 102 103 105 106 107 108 122 Limited Warranty Ordering Replacement PartsIcon Health & Fitness, Inc., 1500 S W., Logan, UT