Gold's Gym GGTL78609.0 manual Wheel must turn freely

Page 8

5.With the help of a second person, carefully tip the treadmill onto its right side. Partially fold the Frame (57) so the treadmill is more stable; do not fully fold the Frame yet.

Attach a Base Foot (93) to the Base (95) in the location shown with a #8 x 1" Tek Screw (4) and a Base Foot Spacer (11). Then, attach another Base Foot (93) with only a #8 x 1" Tek Screw (4). Attach a Wheel (96) with a 3/8" x 2" Bolt (5) and a 3/8" Nut (9). Do not overtighten the Nut; the

Wheel must turn freely.

6.Set the Left Upright Spacer (87) on the Base

(95).Have a second person hold the Left Upright (85) near the Base. Hold a Bolt Spacer

(25)inside the lower end of the Left Upright. Next, insert a 3/8" x 4 1/2" Bolt (6) with a 3/8" Star Washer (10) into the Left Upright and the Bolt Spacer. Repeat this step with a second

Bolt Spacer (25), 3/8" x 4 1/2" Bolt (6), and 3/8" Star Washer (10). Then, set the Left Upright in the Left Upright Spacer.

Partially tighten the 3/8" x 4 1/2" Bolts (6); do not fully tighten the Bolts yet.

With the help of a second person, tip the tread- mill so that the Base (95) is flat on the floor.

7.Set the console assembly face down on a soft surface to avoid scratching the console assem- bly. Identify the Right Handrail (105). Hold the Right Handrail near the console assembly. Next, insert the console wire through the indi- cated holes in the Right Handrail (105) as shown.

5	95
4 93
	57	5

11	93 96	9
4

6	85
6	85
10	87
10
	95
25
7	Console Wire
Console	Holes
Console	105
Assembly

8

Image 8

Contents QUESTIONS? Model No. GGTL78609.0 Serial NoMon.-Fri a.m.-6 p.m. MT Sat a.m.-4 p.m. MT On the WEBTable of Contents Important Precautions Pulse sensor is not a medical devicePage Before YOU Begin Assembly Do not fully fold the Frame yetFul not to pinch the Upright Wire Spacer 92. Be careful not to pinch Upright WireTighten the Nut the Wheel must turn freely Not fully tighten the Bolts yetWheel must turn freely Bar. See the inset drawing. The connectors No wires are pinched. Do not fully tightenConsole assembly. See the inset drawing Should slide together easily and snap intoUprights. Be careful not to pinch any wires 108 Next, hold the receiver so that the antenna is PRE-LUBRICATED Walking Belt Operation and AdjustmentHOW to Plug in the Power Cord Console Diagram Features of the ConsoleInsert the key into the console HOW to Turn on the PowerHOW to USE the Manual Mode Turn on the fans if desired Follow your progress with the displays. The matrix-When youDistance Start the workout HOW to USE a Preset WorkoutSelect a preset workout HOW to Create a Custom Workout Select a custom workoutHOW to USE a Custom Workout HOW to USE AN Ifit Workout Insert an iFit card and select a workoutMake sure that the audio wire is fully plugged Information ModeHOW to USE the Stereo Sound System Optional Chest Pulse Sensor HOW to Fold and Move the Treadmill HOW to Move the TreadmillHOW to Lower the Treadmill for USE Troubleshooting Problem The power turns off during useProblem The walking belt slows when walked on TopProblem Solution Exercise Guidelines Exercise IntensityWorkout Guidelines Exercise FrequencyPart LIST-Model No. GGTL78609.0 Key No. Qty DescriptionQty Exploded Drawing A-Model No. GGTL78609.0 R0709A Exploded Drawing B-Model No. GGTL78609.0 R0709A Exploded Drawing C-Model No. GGTL78609.0 R0709A 10 101 100 104 124 102 103 105 106 107 108 122 Icon Health & Fitness, Inc., 1500 S W., Logan, UT Ordering Replacement PartsLimited Warranty