Gold's Gym GGTL78609.0 manual Top, Problem The walking belt slows when walked on

Page 26
Idler
Roller Bolts
b 2–3 in.

Remove the three #8 x 3/4" Screws (1) and care- fully pivot the Motor Hood (63) off.

63

1

 

Locate the Reed Switch (77) and the Magnet (51)

 

 

on the left side of the Pulley (52). Turn the Pulley

 

 

until the Magnet is aligned with the Reed Switch.

 

 

Make sure that the gap between the Magnet and

1/8 in.

 

the Reed Switch is about 1/8 in. (3 mm). If neces-

 

sary, loosen the #8 x 3/4" Clamp Screw (15), move

 

51

the Reed Switch slightly, and then retighten the

77

Screw. Reattach the Motor Hood (not shown). If

52

necessary, reattach the #12 x 2" Screws (not

Top

 

shown). Run the treadmill for a few minutes to

View

 

check for a correct speed reading.

 

PROBLEM: The incline of the treadmill does not change correctly

 

 

SOLUTION: a. With the key in the console, press one of the Incline buttons. While the incline is changing, re- move the key. After a few seconds, re-insert the key. The treadmill will automatically rise to the maximum incline level and then return to the minimum level. This will recalibrate the incline system.

PROBLEM: The walking belt slows when walked on

SOLUTION: a. Use only a single-outlet surge suppressor that meets all of the specifications described on page 13. b. If the walking belt is overtightened, treadmill per-

formance may decrease and the walking belt may become damaged. Remove the key and UNPLUG THE POWER CORD. Using the hex key, turn both idler roller bolts counterclockwise, 1/4 of a turn.

When the walking belt is properly tightened, you should be able to lift each edge of the walking belt 2 to 3 in. (5 to 7 cm) off the walking platform. Be careful to keep the walking belt centered. Then, plug in the power cord, insert the key, and run the treadmill for a few minutes. Repeat until the walk- ing belt is properly tightened.

c. If the walking belt still slows when walked on, see the front cover of this manual.

26

Page 25 Page 27
Image 26
Page 25 Page 27
Contents Mon.-Fri a.m.-6 p.m. MT Sat a.m.-4 p.m. MT QUESTIONS?Model No. GGTL78609.0 Serial No On the WEBTable of Contents Important Precautions Pulse sensor is not a medical devicePage Before YOU Begin Assembly Do not fully fold the Frame yetTighten the Nut the Wheel must turn freely Ful not to pinch the Upright WireSpacer 92. Be careful not to pinch Upright Wire Not fully tighten the Bolts yetWheel must turn freely Console assembly. See the inset drawing Bar. See the inset drawing. The connectorsNo wires are pinched. Do not fully tighten Should slide together easily and snap intoUprights. Be careful not to pinch any wires 108 Next, hold the receiver so that the antenna is PRE-LUBRICATED Walking Belt Operation and AdjustmentHOW to Plug in the Power Cord Console Diagram Features of the ConsoleInsert the key into the console HOW to Turn on the PowerHOW to USE the Manual Mode Turn on the fans if desired Follow your progress with the displays. The matrix-When youDistance Start the workout HOW to USE a Preset WorkoutSelect a preset workout HOW to Create a Custom Workout Select a custom workoutHOW to USE a Custom Workout HOW to USE AN Ifit Workout Insert an iFit card and select a workoutMake sure that the audio wire is fully plugged Information ModeHOW to USE the Stereo Sound System Optional Chest Pulse Sensor HOW to Fold and Move the Treadmill HOW to Move the TreadmillHOW to Lower the Treadmill for USE Troubleshooting Problem The power turns off during useProblem The walking belt slows when walked on TopProblem Solution Workout Guidelines Exercise GuidelinesExercise Intensity Exercise FrequencyPart LIST-Model No. GGTL78609.0 Key No. Qty DescriptionQty Exploded Drawing A-Model No. GGTL78609.0 R0709A Exploded Drawing B-Model No. GGTL78609.0 R0709A Exploded Drawing C-Model No. GGTL78609.0 R0709A 10 101 100 104 124 102 103 105 106 107 108 122 Icon Health & Fitness, Inc., 1500 S W., Logan, UT Ordering Replacement PartsLimited Warranty
Top Page Image Contents