Gold's Gym GGTL78609.0 manual 108

Page 11

14.Attach the Right Bottom Handrail Cover (108) and the Left Bottom Handrail Cover (104) to the console assembly with four #8 x 3/4" Screws

(1).

15.Raise the Frame (57) to the position shown.

Have a second person hold the Frame until this step is completed.

Orient the Storage Latch (54) so that the large barrel and the Latch Knob (55) are in the posi- tions shown.

Attach the Latch Bracket (36) and the Storage Latch (54) to the Base (95) with two 3/8" x 2" Bolts (5) and two 3/8" Nuts (9).

Attach the upper end of the Storage Latch (54) to the bracket on the Frame (57) with a 3/8" x 2" Bolt (5) and a 3/8" Nut (9). Note: It may be nec- essary to move the Frame back and forth to align the Storage Latch with the bracket.

Lower the Frame (57) (see HOW TO LOWER THE TREADMILL FOR USE on page 24).

	14
	104	Console
	1	Assembly
	1	108
		108
		1
	15	57
		57
	9	5

55	54
55	Large
	Barrel
95	36

9 5

16.Make sure that all parts are properly tightened before you use the treadmill. If there are sheets of clear plastic on the treadmill decals, remove the plastic. To protect the floor or carpet, place a mat under the tread- mill. Note: Extra hardware may be included. Keep the included hex keys in a secure place; one of the hex keys is used to adjust the walking belt (see pages 26 and 27).

11

Image 11

Contents On the WEB QUESTIONS?Model No. GGTL78609.0 Serial No Mon.-Fri a.m.-6 p.m. MT Sat a.m.-4 p.m. MTTable of Contents Pulse sensor is not a medical device Important PrecautionsPage Before YOU Begin Do not fully fold the Frame yet AssemblyNot fully tighten the Bolts yet Ful not to pinch the Upright WireSpacer 92. Be careful not to pinch Upright Wire Tighten the Nut the Wheel must turn freelyWheel must turn freely Should slide together easily and snap into Bar. See the inset drawing. The connectorsNo wires are pinched. Do not fully tighten Console assembly. See the inset drawingUprights. Be careful not to pinch any wires 108 Next, hold the receiver so that the antenna is PRE-LUBRICATED Walking Belt Operation and AdjustmentHOW to Plug in the Power Cord Features of the Console Console DiagramInsert the key into the console HOW to Turn on the PowerHOW to USE the Manual Mode Turn on the fans if desired Follow your progress with the displays. The matrix-When youDistance Start the workout HOW to USE a Preset WorkoutSelect a preset workout Select a custom workout HOW to Create a Custom WorkoutHOW to USE a Custom Workout Insert an iFit card and select a workout HOW to USE AN Ifit WorkoutMake sure that the audio wire is fully plugged Information ModeHOW to USE the Stereo Sound System Optional Chest Pulse Sensor HOW to Move the Treadmill HOW to Fold and Move the TreadmillHOW to Lower the Treadmill for USE Problem The power turns off during use TroubleshootingTop Problem The walking belt slows when walked onProblem Solution Exercise Frequency Exercise GuidelinesExercise Intensity Workout GuidelinesKey No. Qty Description Part LIST-Model No. GGTL78609.0Qty Exploded Drawing A-Model No. GGTL78609.0 R0709A Exploded Drawing B-Model No. GGTL78609.0 R0709A Exploded Drawing C-Model No. GGTL78609.0 R0709A 10 101 100 104 124 102 103 105 106 107 108 122 Icon Health & Fitness, Inc., 1500 S W., Logan, UT Ordering Replacement PartsLimited Warranty