Gold's Gym GGTL78609.0 Bar. See the inset drawing. The connectors, Screws or Patch Bolts yet

Page 9

8.

Locate the speed wire in the end of the Pulse

8

 

 

 

 

 

 

 

Bar (103). Connect the speed wire in the Right

 

 

 

 

 

 

 

Handrail (105) to the speed wire in the Pulse

 

 

 

 

 

105

 

Bar. See the inset drawing. The connectors

 

 

 

Speed Wires

 

 

should slide together easily and snap into

 

Incline

 

 

 

 

place. If they do not, turn one connector and try

 

103

 

 

 

 

again.

 

Wires

 

 

 

 

Locate the the incline wire in the end of the

 

 

 

101

 

 

 

 

Pulse Bar (103). Hold the Left Handrail (101)

 

 

 

 

 

 

 

 

near the console assembly. Connect the incline

 

 

 

 

 

 

 

 

wire in the Left Handrail to the incline wire in the

 

 

 

 

 

 

 

 

Pulse Bar as described above.

 

 

 

 

 

Console

 

 

 

 

 

 

 

 

 

 

 

 

 

Assembly

9.

Insert the speed wires and the incline wires into

9

 

 

105

 

8

 

 

the area at the ends of the Pulse Bar (103).

 

 

 

 

 

Attach the Left Handrail (101) and the Right

 

 

 

 

 

10

2

 

Handrail (105) to the console assembly with four

 

 

 

 

 

 

#8 x 1/2" Screws (2), two 3/8" x 3/4" Patch Bolts

 

 

 

103

 

 

 

 

(8), and two 3/8" Star Washers (10). Make sure

 

 

8

 

 

 

 

no wires are pinched. Do not fully tighten the

101

10

 

 

 

 

 

Screws or Patch Bolts yet.

 

2

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Console

 

 

 

 

 

 

 

Assembly

 

10.

Press the Left Handrail Cover (100) against the

10

 

 

2

 

3

 

 

console assembly. See the inset drawing.

 

 

2

 

 

Align the lip on the Left Handrail Cover with the

 

 

 

 

 

105

 

lip on the console assembly. Make sure no

 

 

 

107

 

 

 

wires are pinched. Then, fully tighten the four

 

 

 

 

 

 

 

#8 x 1/2" Screws (2) in the Left Handrail (101).

 

 

 

 

 

 

 

 

Note: The Screws are preattached.

 

2 1002

3

 

 

 

 

Repeat this step with the Right Handrail

 

 

 

 

 

Cover (107).

 

 

 

 

 

 

 

 

Tighten two 1/4" x 1/2" Bolts (3) into the

 

 

 

 

 

 

 

 

Handrails (101, 105) and the console assembly.

 

 

 

 

 

 

 

 

See step 9. Fully tighten the four #8 x 1/2"

 

 

 

101

 

Console

 

Screws (2) and the two 3/8" x 3/4" Patch Bolts

 

 

 

 

 

(8).

Lips

 

 

 

Assembly

 

 

 

 

 

 

 

 

 

9

 

 

 

 

 

 

Image 9
Contents Model No. GGTL78609.0 Serial No QUESTIONS?Mon.-Fri a.m.-6 p.m. MT Sat a.m.-4 p.m. MT On the WEBTable of Contents Pulse sensor is not a medical device Important PrecautionsPage Before YOU Begin Do not fully fold the Frame yet AssemblySpacer 92. Be careful not to pinch Upright Wire Ful not to pinch the Upright WireTighten the Nut the Wheel must turn freely Not fully tighten the Bolts yetWheel must turn freely No wires are pinched. Do not fully tighten Bar. See the inset drawing. The connectorsConsole assembly. See the inset drawing Should slide together easily and snap intoUprights. Be careful not to pinch any wires 108 Next, hold the receiver so that the antenna is Operation and Adjustment HOW to Plug in the Power CordPRE-LUBRICATED Walking Belt Features of the Console Console DiagramHOW to Turn on the Power HOW to USE the Manual ModeInsert the key into the console Follow your progress with the displays. The matrix-When you DistanceTurn on the fans if desired HOW to USE a Preset Workout Select a preset workoutStart the workout Select a custom workout HOW to Create a Custom WorkoutHOW to USE a Custom Workout Insert an iFit card and select a workout HOW to USE AN Ifit WorkoutInformation Mode HOW to USE the Stereo Sound SystemMake sure that the audio wire is fully plugged Optional Chest Pulse Sensor HOW to Move the Treadmill HOW to Fold and Move the TreadmillHOW to Lower the Treadmill for USE Problem The power turns off during use TroubleshootingTop Problem The walking belt slows when walked onProblem Solution Exercise Intensity Exercise GuidelinesWorkout Guidelines Exercise FrequencyKey No. Qty Description Part LIST-Model No. GGTL78609.0Qty Exploded Drawing A-Model No. GGTL78609.0 R0709A Exploded Drawing B-Model No. GGTL78609.0 R0709A Exploded Drawing C-Model No. GGTL78609.0 R0709A 10 101 100 104 124 102 103 105 106 107 108 122 Ordering Replacement Parts Limited WarrantyIcon Health & Fitness, Inc., 1500 S W., Logan, UT