Healthrider HRTL19913 manual Troubleshooting and Maintenance, Problemsolution, Unplug Power Cord

Page 25

TROUBLESHOOTING AND MAINTENANCE

Most treadmill problems can be solved by following the instructions below. If further assistance is needed, please call our Customer Service Department toll-free at 1-800-999-3756, Monday through Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays).

PROBLEMSOLUTION

1.The power does not turn on

a. Make sure that the power cord is plugged into a surge suppressor, and that the surge suppressor is plugged into a properly grounded outlet (see page 8). Use only a single-outlet surge suppressor that meets all of the specifications described on page 8. Important: The treadmill is not compatible with GFCI-equipped outlets.

b. Make sure that the key is fully inserted into the console.

 

 

 

 

 

 

 

 

 

 

c. Check the circuit breaker located on the frame near

 

 

 

 

 

 

 

 

 

 

 

c

 

 

 

 

 

 

 

the power cord. If the switch protrudes as shown, the

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

circuit breaker has tripped. To reset the circuit

 

 

 

 

 

 

 

 

 

 

breaker, wait for five minutes and then press the

 

 

 

 

 

 

 

 

 

 

switch back in.

 

 

 

 

Tripped

 

 

 

 

 

 

 

 

 

 

Reset

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

d. Check the on/off switch located on the frame near

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

d

 

 

 

 

 

the power cord. The switch must be in the on posi-

 

 

On

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

tion.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Position

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

2. The power turns off

a. Check the circuit breaker located on the treadmill frame near the power cord (see

 

during use

1. c. above). If the circuit breaker has tripped, wait for five minutes and then press

 

 

the switch back in.

 

 

 

 

 

 

b. Make sure that the power cord is plugged in.

 

 

 

 

c. Remove the key from the console and then reinsert it.

 

 

 

d. Make sure that the on/off switch is in the on position (see 1. d. above).

 

3. The walking belt

a. Use only a single-outlet surge suppressor that meets all of the specifications de-

 

slows when walked

scribed on page 8.

 

 

 

 

 

on

 

 

 

 

 

 

 

b. If the walking belt is overtightened, tread-

b

3–4”

 

mill performance may decrease and the

 

 

 

 

 

walking belt may be permanently dam-

 

 

 

 

aged. Remove the key and

UNPLUG THE

 

 

 

POWER CORD

. Using the included allen

 

 

 

wrench, turn both rear roller adjustment

 

 

 

 

bolts counterclockwise 1/4 of a turn. When

 

 

 

 

the walking belt is properly tightened, you

 

 

 

 

should be able to lift

 

the edges

of the

Rear Roller Adjustment Bolts

 

walking belt 3 to 4 inches off the walking

 

 

 

 

platform. Be careful to keep the walking

 

 

 

 

belt centered. Plug in the power cord, insert the key and run the treadmill for a few

 

 

minutes. Repeat until the walking belt is properly tightened.

 

 

25

Page 24 Page 26
Image 25
Page 24 Page 26
Contents Model No. HRTL19913 Serial No QUESTIONS?Customer HOT Line Mon.-Fri., 6 a.m.- 6 p.m. MSTTable of Contents Never move the walking belt while the power Important PrecautionsUse the treadmill only as described in this manual A fall and serious injuryNever drop or insert any object into any open- ing To the next settings of the CD or video programBefore YOU Begin Using the treadmillBack Assembly requires two people AssemblyWith the help of a second person,carefully raise Chest Pulse Sensor Care and Maintenance HOW to PUT on the Chest Pulse SensorChest Pulse Sensor Troubleshooting Self near the center of the walking beltTreadmill Operation HOW to Plug in the Power CordPerformant Lube Right. To purchase a surge suppressor, seeSheet of clear plastic On the face Console, remove it Features of the ConsoleWith the treadmill connected to your computer, you Follow Steps beginning onSection refer to miles HOW to Turn on the Power HOW to USE the Manual ModeDisplays Refer to page 23 and turn off the demo modePulse display Moving your HandsSelect one of the six preset programs HOW to USE the Preset ProgramsStart the program Program displayUsing hand 4Use the hand weights, if desiredFollow your progress with the displays If you have heart probWhen the program has ended, remove the key Enter a maximum heart rate settingSelect one of the two custom programs HOW to Create Custom ProgramsTo the left Column to the rightAll speed HOW to USE Custom ProgramsFlashing Current LeftHOW to Connect Your Portable Stereo HOW to Connect Your Portable CD PlayerVideocassettes HOW to Connect Your Computer HOW to Connect Your Home StereoPlug the adapter into the Line OUT jack on your stereo Adapter CablePrograms HOW to Connect Your VCRWhen the CD or video program is completed, Next settings of the CD or video programMove at 1 mph + button on the consoleNext settings for the program HOW to USE Programs Directly from OUR WEB SiteFollow the on-line instructions to start Program Return to the treadmill and stand on the footStore. When the console is in the demo mode, Information MODE/DEMO ModeButton so the Pulse display is blank HOW to Fold the Treadmill for Storage HOW to Fold and Move the TreadmillHOW to Move the Treadmill HOW to Lower the Treadmill for USEProblemsolution Troubleshooting and MaintenanceUnplug Power Cord Console do not func CordTion properly Exercise Intensity Exercise GuidelinesWorkout Guidelines Exercise FrequencySuggested Stretches Page Key Qty Description HOW to Order Replacement Parts Part No R0402A Limited WarrantyR0402A Exploded DRAWING-Model No
Top Page Image Contents