Gold's Gym GGSY69530 manual Locknut the Leg Lever must be able to pivot easily

Page 13

20.Lubricate an M12 x 102mm Bolt (81) with grease. Attach the Press Frame (14) to the Right Base (1) with the Bolt and an M12 Locknut (95). Make sure the hole is closer to the indicated side of the Press Frame. Do not overtighten the Locknut; the Press Frame must be able to pivot easily.

21.Press a 50mm Square Inner Cap (43) into a Press Arm (15). Press two 25mm Round Inner Caps (65) into the Press Arm.

Wet the handles on the Press Arm (15) with soapy water. Slide two Grips (68) onto the han- dles.

Attach the Press Arm (15) to the Press Frame

(14)with two M10 x 70mm Bolts (87) and two

M10 Nylon Locknuts (75).

Attach the other Press Arm (15) to the Press Frame (14) in the same manner.

22.Press two 50mm Square Inner Caps (43) into the Leg Lever (18).

Lubricate an M10 x 78mm Bolt (85) with grease. Orient the Leg Lever (18) as shown and attach it to the Left Leg (8) with the Bolt and an M10 Nylon Locknut (75). Do not overtighten the

Locknut; the Leg Lever must be able to pivot easily.

23.Lubricate both axles on the Left Top Frame (11) with grease.

Slide the Left Fly Pivot (21) onto the indicated axle on the Left Top Frame (11). Set two 25mm Retainer Rings (53) on a 25mm Round Outer Cap (47). Make sure the teeth on the Rings are toward the Cap, as shown in the inset draw- ing. Tap the Retainer Rings and Outer Cap onto the axle. Repeat with the Right Fly Pivot (22).

20

 

 

 

14

 

 

Hole

 

 

95

 

 

81

 

 

1

 

 

 

Lubricate

21

 

 

15

68

43

 

 

 

 

 

65

 

75

15

 

 

87

14

 

 

 

22

75

43

 

 

85

 

 

 

 

18

Lubricate

8

Small

 

 

 

 

Slot

 

 

43

23

 

11

 

 

 

 

Axle

 

22

 

Axle

 

21

53

 

53

 

 

47

 

47

 

 

13

Image 13
Contents Model No. GGSY69530 Serial No QUESTIONS?Customer HOT Line Mon.-Fri., 6 a.m.-6 p.mTable of Contents Important Precautions Right Side Before YOU BeginLeft Side Make Assembly Easier for Yourself AssemblyTighten the Locknuts yet Frame AssemblyPage Do not tighten the Locknuts yet Lubricate Pin Groove Slot Locknuts yet Page Open the part bag labeled ARM Assembly Arm AssemblyTighten the M10 Nylon Locknuts 75 used in steps Locknut the Leg Lever must be able to pivot easily Cable Assembly Page Page Bracket Large Ball Locate the Long Cable 62. Attach the eyelet Cable Trap is turned to hold the Cable Groove of the PulleyLocknut yet Page Cable Trap is turned to hold the Cable Place Locate and open the parts bag labeled Seat Assembly Seat AssemblySeat Frame not shown in the same manner Page Adjusting the Backrests AdjustmentsAdjusting the Curl PAD Store the Curl Pad out of the way of the weight systemChanging the Weight Setting Weight High Press LEG Butter LOW Pulley ARM FLY ARM Lever Weight Resistance ChartLbs Tightening the Cables TroubleshootingHigh Cable Cable DiagramsLong Cable Low Cable Butterfly CableExercise Guidelines Cooling Down Muscle ChartStaying Motivated Date Exercise Weight Sets RepsAerobic Exercise Thursday Aerobic Exercise DatePart Identification CHART- Model No. GGSY69530 Page Page R0903A Part LIST-Model No. GGSY69530Qty Description Exploded DRAWING-Model No Limited Warranty Ordering Replacement PartsIcon Health & FITNESS, INC., 1500 S W., LOGAN, UT