Gold's Gym GGSY69530 Cable Trap is turned to hold the Cable Groove of the Pulley, Locknut yet

Page 18

41. Wrap the High Cable (61) over a 90mm Pulley

41

 

 

 

 

 

(38). Attach the Pulley to the Right Top Frame

 

 

 

 

 

 

 

 

 

 

 

(10) with an M10 x 45mm Bolt (78) and an M10

 

 

 

 

 

10

Nylon Locknut (75).

 

 

 

 

 

38

 

 

 

 

 

 

 

 

75

 

 

 

78

 

 

 

 

 

 

61

42. Wrap the High Cable (61) under a 90mm Pulley

42

 

 

 

 

 

(38). Attach the Pulley and a Cable Trap (37) to

 

 

 

 

 

 

 

 

 

 

 

the second set of holes from the top of the

 

 

37

 

 

 

Double “U”-bracket (41) with an M10 x 48mm Bolt

 

 

 

61

(23) and an M10 Nylon Locknut (75). Make sure

 

 

 

 

 

38

the Cable Trap is turned to hold the Cable in

 

 

 

 

 

 

 

 

 

 

 

the groove of the Pulley.

 

 

75

 

 

41

 

 

 

 

 

 

 

 

 

 

23

 

 

 

 

 

 

43. Route the High Cable (61) up through the Right

43

85

 

61

 

 

Top Frame (10) and over a 90mm Pulley (38).

 

 

38

 

 

 

Attach the Pulley inside the Top Frame with an

 

74

 

 

 

 

 

 

 

 

 

 

M10 x 78mm Bolt (85), two M10 Washers (74),

 

 

 

 

 

 

two 17mm Spacers (58), and an M10 Nylon

 

58

 

 

 

 

Locknut (75).

 

 

 

 

 

 

 

 

 

 

 

 

 

10

 

 

 

74

 

 

 

 

 

 

 

 

 

 

 

 

58

 

 

 

 

 

 

75

44. Route the High Cable (61) over a 90mm Pulley

44

 

 

61

 

 

(38) and down through the Right Top Frame (10).

 

38

 

 

 

75

 

 

Attach the Pulley inside the Top Frame with an

 

 

 

 

 

 

74

 

10

 

 

M10 x 78mm Bolt (85), two M10 Washers (74),

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

two 17mm Spacers (58), and an M10 Nylon

 

58

 

 

 

 

Locknut (75).

 

 

 

74

 

 

 

 

 

58

 

 

 

 

 

 

 

85

 

45. Locate the Long Cable (62). Attach the eyelet

45

 

 

 

 

 

on the Cable to the Right Upright (5) with an M10

 

 

 

 

 

 

 

 

 

 

 

x 110mm Bolt (88), an M10 Small Washer (33),

 

 

 

 

 

 

and an M10 Nylon Locknut (75). Do not tighten

 

75

 

 

 

 

the Locknut yet.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

5

 

33

 

 

 

 

 

 

 

 

 

 

 

62

88

18

Image 18
Contents Customer HOT Line QUESTIONS?Model No. GGSY69530 Serial No Mon.-Fri., 6 a.m.-6 p.mTable of Contents Important Precautions Before YOU Begin Right SideLeft Side Assembly Make Assembly Easier for YourselfFrame Assembly Tighten the Locknuts yetPage Do not tighten the Locknuts yet Lubricate Pin Groove Slot Locknuts yet Page Arm Assembly Open the part bag labeled ARM AssemblyTighten the M10 Nylon Locknuts 75 used in steps Locknut the Leg Lever must be able to pivot easily Cable Assembly Page Page Bracket Large Ball Cable Trap is turned to hold the Cable Groove of the Pulley Locate the Long Cable 62. Attach the eyeletLocknut yet Page Cable Trap is turned to hold the Cable Place Seat Assembly Locate and open the parts bag labeled Seat AssemblySeat Frame not shown in the same manner Page Adjusting the Curl PAD AdjustmentsAdjusting the Backrests Store the Curl Pad out of the way of the weight systemChanging the Weight Setting Weight Resistance Chart Weight High Press LEG Butter LOW Pulley ARM FLY ARM LeverLbs Troubleshooting Tightening the CablesCable Diagrams High CableLong Cable Butterfly Cable Low CableExercise Guidelines Muscle Chart Cooling DownStaying Motivated Aerobic Exercise Exercise Weight Sets RepsDate Thursday Aerobic Exercise DatePart Identification CHART- Model No. GGSY69530 Page Page Part LIST-Model No. GGSY69530 R0903AQty Description Exploded DRAWING-Model No Ordering Replacement Parts Limited WarrantyIcon Health & FITNESS, INC., 1500 S W., LOGAN, UT