Precor C932 owner manual Selecting the Language, Determining the Units of Measure

Page 22

C O M M E R C I A L P R O D U C T S D I V I S I O N

SELECTING THE LANGUAGE

Display prompts can appear in English, German, Spanish, French, Dutch, or Portuguese. Use the ▼▲ keys to display your preference and press SELECT.

DETERMINING THE UNITS OF MEASURE

The C932 can display units of measure in either U.S. Standard (miles, miles per hour) or Metric (kilometers, kilometers per hour). When the treadmill is shipped from the factory it is set to display U.S. Standard units of measure.You can easily change this setting by taking the following steps:

1.Check that the C932 is ON. If necessary, turn ON the treadmill using the power switch located at the front of the unit.

2.At the scrolling PRECOR banner, press the following keys in sequence:

RESET, SELECT, SPEED ▼, SELECT, INCLINE ▲, SELECT, SPEED ▼, SELECT

Numbers appear associated with the key that you pressed: 5,6,5,1,5,6,5

Important: If the second key (SELECT) is not pressed within 1/2 second after RESET, the display returns to the PRECOR banner and you need to begin again.

3.The prompt, SELECT UNITS scrolls across the display and then, the current unit of measure appears. The message scrolls continually until you press a key. Any ▼ or ▲ key lets you alternate between the prompts.

4.Once your selection is displayed, three options exist. You can,

a.press the SELECT to accept the unit of measure being displayed and continue with programming the treadmill. (Refer to Determining the Club Speed Limit.) The changes are saved in memory. The C932 will retain your selection even when it is turned OFF and unplugged.

b.press the red Stop button, which keeps the “current unit of measure”, unchanged and advances to the next section.

Note: The “current unit of measure” is not necessarily the one being dis- played. It refers to the unit of measure that was in existence prior to entering the SELECT UNITS program.

c.press RESET, which keeps the “current unit of measure”, unchanged, ends programming mode, and returns to the PRECOR banner.

Important: If you change the Unit of Measure display, be sure to check the speed limit setting to verify that it is correct. Refer to Determining the Club Speed Limit below.

page 22

Image 22

Contents C932 Important Safety Instructions Safety Approval Grounding InstructionsTable of Contents C932 Keypad Back coverRadio Frequency Interference RFI European ApplicationsObtaining Service About this ManualStandard Equipment Unpacking the TreadmillOther Equipment Acquire Additional Tools Hardware KITOr crescent wrench Assembly Instructions Setting Up the TreadmillInstallation Requirements To assemble the treadmill, take the following stepsM M E R C I a L P R O D U C T S D I V I S I O N M M E R C I a L O D U C T S V I S I O N Diagram 7 Install the display console Diagram Follow steps 9a. through 9d. on the opposite side M M E R C I a L O D U C T S V I S I O N Level the unit Turning the Unit on and OFF Checking the Alignment of the Running Belt If the running belt ThenClub Information Programming Tips Always start at the scrolling Precor bannerSelecting the Language Determining the Units of MeasureSetting a Pause Time Limit Setting a Workout Time LimitDetermining the Club Speed Limit Setting a Cool Down Time Limit RESET, Speed , SelectER33 AT 12,345,678 Miles 1,714 Hours Features on the Display Console C932 DisplaySetup Mode and Prompts To continue in Setup mode, press SelectSetup Mode and the Quickstarttm Feature If QuickStart is pressed at Following occursCenter Display During a Workout M M E R C I a L P R O D U C T S D I V I S I O N Keypad Tips C932 KeypadSpecial Keypad Functions AT the Precor Banner Keys on the Keypad Keypad keysRefer to Obtaining Service on Setup Prompts Default ValueSmartRate display will appear when a user wears Polar chest strap. If no Age entry occurs, thenChanging the Display Features Using the Select KEY Using the Handrails Safety FeaturesUsing the Security Clip Exercising on the C932Keypad Tips Using the Stop ButtonReviewing Keypad and Workout Tips Workout TipsQuick Steps to Working OUT Straddle beltCooling Down After Your Workout PAUSE, Workout SUMMARY, and Exit Features StopCourse where you left off Features remain, so you can review yourExits Pause mode and starts the running To a gradual stop. Note that you may alsoCourse Features C932 CoursesCourse Descriptions Manual ManlWeight Loss Wtls Using the Smartrate Feature Heart Rate CapabilitiesHeart Rate Target Zones Heart Rate Course Inspection MaintenanceCleaning the Equipment Aligning the Running BeltM M E R C I a L P R O D U C T S D I V I S I O N Storing the Polar Chest Strap Servicing the TreadmillLong Term Storage C932 View 1 of 8View 2 of 8 View 3 of 8 View 4 of 8 View 5 View 6 View 7 of 8 View 8 of 8 Thank You and Welcome to Precor Please indicate the type and number of products purchased Date of Purchase Purchased from Dealer nameProduct Serial Numbers How many members do you have?Conditions and Restrictions Limited WarrantyWarranty Periods and Coverage Complete this portion and keep for your recordsProduct Features Product SpecificationsElectronic Specifications