Precor C932 Setup Prompts Default Value, SmartRate display will appear when a user wears

Page 33

C O M M E R C I A L P R O D U C T S D I V I S I O N

When a user presses QuickStart at the PRECOR banner, the default values shown below apply.

QUICKSTART Default Values

Setup Prompts

Default Value

Course

Manual (MANL)

Workout time

Club limit

Weight

150 lbs. (68 kg.)

AGE 0 :

A valid AGE must be entered to use the SmartRate® dis-

 

play. If QuickStart is pressed after an age is entered, then

 

the SmartRate display will appear when a user wears the

 

POLAR® chest strap. If no “Age” entry occurs, then

 

SmartRate LED’s light but are not activated. Note that the

 

POLAR® chest strap is available through your Precor dealer.

 

Refer to Obtaining Service on page 7.

SELECT key: While the PRECOR banner is displayed, the SELECT key accesses the Setup mode. Refer to Setup Mode and Prompts on page 27. During a course, the SELECT key changes what features appear on the display. To learn about which features appear on the display or setting up an automatic scan of the work- out data, refer to Changing the Display Features Using the SELECT Key.

SPEED ▼▲: During a workout, the SPEED keys let a user decease or increase the running belt’s speed. The display can show a range from 0.5 to 11.0 miles per hour (1.0 to 18.0 kilometers per hour) and changes can be made in 0.1 increments.

When a user changes the speed by pressing the SPEED ▲ or ▼ key, the num- ber that appears on the display shows the target speed (not necessarily, the present speed of the running belt) because the changes to the display can occur much faster than the belt speed.

Any time during a workout, a user can view the actual speed by lightly tapping either SPEED ▲ or ▼ key.The “pace” (minutes per mile) appears in the left-most display. A user can opt to change the speed, if they hold the key down for more than one second.

During Setup mode, the SPEED ▲ ▼ keys are used for data selection. Pressing either ▼ or ▲ key does not affect the running belt. However the ▲ or ▼ keys do affect what appears on the display. Refer to Setup Mode and Prompts on page 27.

Stop button: The red Stop button is not part of the keypad, but it is an integral part of the display console. Anytime during a workout, a firm tap on the red Stop button slows the running belt to a stop. The treadmill retains a user’s workout statistics and enters Pause mode. The club has the ability to limit the amount of time a user can remain in pause mode. Refer to Club Information on page 20.

For a user to resume working out within the time frame allotted, he or she can press the SPEED ▲ until the desired speed of the running belt is reached.

page 33

Page 32 Page 34
Image 33
Page 32 Page 34
Contents C932 Important Safety Instructions Grounding Instructions Safety ApprovalTable of Contents Back cover C932 KeypadEuropean Applications Radio Frequency Interference RFIAbout this Manual Obtaining ServiceUnpacking the Treadmill Standard EquipmentOther Equipment Hardware KIT Acquire Additional ToolsOr crescent wrench Installation Requirements Setting Up the TreadmillAssembly Instructions To assemble the treadmill, take the following stepsM M E R C I a L P R O D U C T S D I V I S I O N M M E R C I a L O D U C T S V I S I O N Diagram 7 Install the display console Diagram Follow steps 9a. through 9d. on the opposite side M M E R C I a L O D U C T S V I S I O N Level the unit Turning the Unit on and OFF If the running belt Then Checking the Alignment of the Running BeltClub Information Always start at the scrolling Precor banner Programming TipsDetermining the Units of Measure Selecting the LanguageSetting a Workout Time Limit Setting a Pause Time LimitDetermining the Club Speed Limit RESET, Speed , Select Setting a Cool Down Time LimitER33 AT 12,345,678 Miles 1,714 Hours C932 Display Features on the Display ConsoleTo continue in Setup mode, press Select Setup Mode and PromptsIf QuickStart is pressed at Following occurs Setup Mode and the Quickstarttm FeatureCenter Display During a Workout M M E R C I a L P R O D U C T S D I V I S I O N C932 Keypad Keypad TipsSpecial Keypad Functions AT the Precor Banner Keypad keys Keys on the KeypadSmartRate display will appear when a user wears Setup Prompts Default ValueRefer to Obtaining Service on Polar chest strap. If no Age entry occurs, thenChanging the Display Features Using the Select KEY Using the Security Clip Safety FeaturesUsing the Handrails Exercising on the C932Reviewing Keypad and Workout Tips Using the Stop ButtonKeypad Tips Workout TipsStraddle belt Quick Steps to Working OUTCooling Down After Your Workout Stop PAUSE, Workout SUMMARY, and Exit FeaturesExits Pause mode and starts the running Features remain, so you can review yourCourse where you left off To a gradual stop. Note that you may alsoC932 Courses Course FeaturesManual Manl Course DescriptionsWeight Loss Wtls Heart Rate Capabilities Using the Smartrate FeatureHeart Rate Target Zones Heart Rate Course Cleaning the Equipment MaintenanceInspection Aligning the Running BeltM M E R C I a L P R O D U C T S D I V I S I O N Servicing the Treadmill Storing the Polar Chest StrapLong Term Storage View 1 of 8 C932View 2 of 8 View 3 of 8 View 4 of 8 View 5 View 6 View 7 of 8 View 8 of 8 Thank You and Welcome to Precor Product Serial Numbers Date of Purchase Purchased from Dealer namePlease indicate the type and number of products purchased How many members do you have?Warranty Periods and Coverage Limited WarrantyConditions and Restrictions Complete this portion and keep for your recordsProduct Specifications Product FeaturesElectronic Specifications
Top Page Image Contents